LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2001 >> Explorer Chassis >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window System >> System Tests >> Test G: Right Rear Power Window Inoperative
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test G: Right Rear Power Window Inoperative

NOTE: After all repairs, clear DTCs and recheck system operation. See WIRING DIAGRAMS  for circuit identification and repair.
  1. Turn ignition switch to LOCK position. Disconnect right rear window switch 7-pin harness connector C802. Ensure window lock-out switch on master window/door lock switch is in UNLOCK position. Turn ignition switch to RUN position. Measure voltage between ground and right rear window switch harness connector C802 terminal No. 4 (Red/Light Blue wire). See Figure . If more than 10 volts exist, go to next step. If 10 volts or less exist, go to step  3 .
  2. Turn ignition switch to LOCK position. Measure resistance between ground and right rear window switch harness connector C802 terminal No. 6 (Red/Black wire). Measure resistance between ground and right rear window switch harness connector C802 terminal No. 1 (Yellow/Black wire). If resistance is less than 5 ohms in both measurements, go to step  6 . If resistance is 5 ohms or more in either measurement, go to step  4 .
  3. Disconnect master window/door lock switch 20-pin connector. Measure resistance between master window/door lock switch terminals No. 19 and 20 (component side). See Figure . If resistance is 5 ohms or more, replace master window/door lock switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION. If resistance is less than 5 ohms, repair open in Red/Light Blue wire(s) between master window/door lock control switch and right rear window switch.
  4. Turn ignition switch to LOCK position. Disconnect master window/door lock switch 20-pin harness connector C501. Measure resistance of Yellow/Black wire between master window/door lock switch harness connector C501 terminal No. 16 and right rear window switch harness connector C802 terminal No. 1. See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open or high resistance in Yellow/Black wire.
  5. Measure resistance of Red/Black wire between master window/door lock switch harness connector C501 terminal No. 18 and right rear window switch harness connector C802 terminal No. 6. If resistance is less than 5 ohms, replace master window/door lock switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION. If resistance is 5 ohms or more, repair open or high resistance in Red/Black wire.
  6. Connect jumper wire between right rear window switch harness connector C802 terminals No. 1 (Yellow/Black wire) and No. 2 (Brown wire). See Figure . Connect second jumper wire between right rear window switch harness connector C802 terminals No. 4 (Red/Light Blue wire) and No. 5 (Brown/Yellow wire). If window does not operate in downward direction, remove jumper wires and go to next step. If window operates in downward direction, but did not operate from right rear window switch, replace right rear window switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION. If window operates in downward direction and operates from right rear window switch, but did not operate from master window/door lock switch, replace master window/door lock switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION.
  7. Turn ignition switch to LOCK position. Connect jumper wire between right rear window switch harness connector C802 terminals No. 5 (Brown/Yellow wire) and No. 6 (Red/Black wire). See Figure . Connect second jumper wire between right rear window switch harness connector C802 terminals No. 2 (Brown wire) and No. 4 (Red/Light Blue wire). If window does not operate in upward direction, remove jumper wires and go to next step. If window operates in upward direction, but did not operate with right rear window switch, replace right rear window switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION. If window operates in upward direction and operates with right rear window switch, but did not operate with master window/door lock switch, replace master window/door lock switch. See POWER WINDOW SWITCH  under REMOVAL & INSTALLATION.
  8. Turn ignition switch to LOCK position. Disconnect right rear window motor 2-pin harness connector C801. Measure resistance of Brown wire between right rear window switch harness connector C802 terminal No. 2 and right rear window motor harness connector C801. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open or high resistance in Brown wire.
  9. Measure resistance of Brown/Yellow wire between right rear window switch harness connector C802 terminal No. 5 and right rear window motor harness connector C801. If resistance is less than 5 ohms, replace right rear window motor. See POWER WINDOW MOTOR  under REMOVAL & INSTALLATION. If resistance is 5 ohms or more, repair open or high resistance in Brown/Yellow wire.
scientia non olet · About LEMON Manuals