| - |
The Air Bag Indicator is Illuminated Continuously - RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground |
GO to PINPOINT TEST A
. |
| B1231 |
Crash Data Memory Full |
Install a new RCM and impact sensors. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT
. |
| B1317 |
Battery Voltage High |
CHECK battery voltage; to be below 16 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION
. |
| B1318 |
Battery Voltage Low |
CHECK battery voltage; to be above 9.0 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION
. |
| B1342 |
RCM Is Faulted |
GO to PINPOINT TEST B |
| B1869 |
Lamp Air Bag Warning Indicator Circuit Open or Short to Ground |
GO to PINPOINT TEST C
. |
| B1870 |
Lamp Air Bag Warning Indicator Circuit Short to Battery |
GO to PINPOINT TEST D
. |
| B1884 |
PAD Warning Lamp Circuit Failure |
GO to PINPOINT TEST E
. |
| B1890 |
PAD Warning Lamp Circuit Short to Battery |
GO to PINPOINT TEST F
. |
| B1891 |
Air Bag Tone Warning Indicator Circuit Short to Battery |
GO to PINPOINT TEST G
. |
| B1892 |
Air Bag Tone Warning Indicator Circuit Open or Short to Ground |
GO to PINPOINT TEST H
. |
| B1921 |
Air Bag Diagnostic Monitor Ground Circuit Open |
GO to PINPOINT TEST I
. |
| B2290 |
Occupant Classification Sensor (OCS) System Fault |
GO to PINPOINT TEST J
. |
| B2292 |
Restraint System - Safety Belt Pretensioner Fault |
GO to PINPOINT TEST K
. |
| B2293 |
Restraint System - Air Bag Fault |
GO to PINPOINT TEST L
. |
| B2294 |
Restraint System - Safety Canopy Fault |
GO to PINPOINT TEST M
. |
| B2295 |
Restraint System - Side Air Bag Fault |
GO to PINPOINT TEST N
. |
| B2296 |
Restraint System - Impact Sensor Fault |
GO to PINPOINT TEST O
. |
| B2432 |
Driver Safety Belt Buckle Switch Circuit Open |
GO to PINPOINT TEST P
. |
| B2433 |
Driver Safety Belt Buckle Switch Circuit Short to Battery |
GO to PINPOINT TEST Q
. |
| B2434 |
Driver Safety Belt Buckle Switch Circuit Short to Ground |
GO to PINPOINT TEST R
. |
| B2435 |
Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range |
GO to PINPOINT TEST S
. |
| B2436 |
Passenger Safety Belt Buckle Switch Circuit Open |
GO to PINPOINT TEST T
. |
| B2437 |
Passenger Safety Belt Buckle Switch Circuit Short to Battery |
GO to PINPOINT TEST U
. |
| B2438 |
Passenger Safety Belt Buckle Switch Circuit Short to Ground |
GO to PINPOINT TEST V
. |
| B2439 |
Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range |
GO to PINPOINT TEST W
. |
| B2477 |
Module Configuration Error |
INSTALL a new RCM. |
| B2909 |
Belt Tension Sensor Fault |
GO to PINPOINT TEST X
. |
| C1414 |
Incorrect Module Design Level |
GO to PINPOINT TEST Y
. |
| C1946 |
Driver Seat Track Position Sensor Circuit Open |
GO to PINPOINT TEST Z
. |
| C1947 |
Driver Seat Track Position Sensor Circuit Short to Ground |
GO to PINPOINT TEST AA
. |
| C1948 |
Driver Seat Track Position Sensor Circuit Resistance Out Of Range |
GO to PINPOINT TEST AB
. |
| C1982 |
Driver Seat Track Position Sensor Short to Battery Fault |
GO to PINPOINT TEST AC
. |
| - |
No Communication with the Restraints Control Module |
GO to PINPOINT TEST AD
. |