LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2007 >> Edge SE, AWD >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Automatic Transaxle/Transmission DTCS
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Automatic Transaxle/Transmission DTCS

AUTOMATIC TRANSAXLE/TRANSMISSION DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC Grouping Component Description Condition Symptom Perform Test
P0657 - Transaxle Solenoid Power Control (TSPC) TSPC electrical circuit failure. TSPC provides power to all the solenoids. This DTC sets if the TSPC circuit is open.
  • No voltage to solenoids.
  • Defaults to 5th gear.
  • Only REVERSE and NEUTRAL available.
  • Will turn on multi-function indicator lamp (MIL).
 Go to Pinpoint Test E .
P0705 P0705, P1702 Transmission Range (TR) Sensor TR sensor circuit failure. PCM is received an invalid combination of the 4-bit signal from the TR sensor.
  • Possible no crank.
  • Only PARK, REVERSE, NEUTRAL and 5th gear available.
  • Harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened.
    • Harsh engagements.
    • Poor performance (due to a 5th gear drive away).
    • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test D .
P0706 P0706, P0709 TR Sensor TR sensor range failure. TR sensor A circuit range/performance. TR sensor stuck in transition zone (possible wiring, connector or TR sensor issue).
  • Possible no crank.
  • Only PARK, REVERSE, NEUTRAL and 5th gear available.
  • Harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened.
    • Harsh engagements.
    • Poor performance (due to a 5th gear drive away).
    • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test D .
P0708 P0708, P1702 TR Sensor TR sensor circuit failure. PCM is received all 4 TR sensor bits open (potential sensor disconnected, wiring, connector or TR sensor issue).
  • Possible no crank.
  • Only PARK, REVERSE, NEUTRAL and 5th gear available.
  • Harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened.
    • Harsh engagements.
    • Poor performance (due to a 5th gear drive away).
    • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test D .
P0709 P0709
or
P0706, P0709		 TR Sensor TR sensor range failure. TR sensor A circuit range/performance. TR sensor stuck in transition zone (possible wiring, connector or TR sensor issue).
  • Possible no crank.
  • Only PARK, REVERSE, NEUTRAL and 5th gear available.
  • Harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened.
    • Harsh engagements.
    • Poor performance (due to a 5th gear drive away).
    • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test D .
P0710 - Transmission Fluid Temperature (TFT) TFT sensor circuit voltage input too low or too high.
  • TFT sensor input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue).
  • Also see P0712 and P0713.
  • Torque converter clutch (TCC) and stabilized shift schedule may be enabled sooner after cold start.
  • Harsh or soft shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test B .
P0710 P0710, P0712 TFT TFT sensor circuit voltage input too low. TFT sensor input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue).
  • TCC and stabilized shift schedule may be enabled sooner after cold start.
  • Harsh or soft shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test B .
P0710 P0710, P0713 TFT TFT sensor circuit voltage too high. TFT sensor input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue).
  • TCC and stabilized shift schedule may be enabled sooner after cold start.
  • Harsh or soft shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test B .
P0711 - TFT No change in TFT sensor input. PCM has detected no TFT change at low-range or high-range during operation.
  • TCC and stabilized shift schedule may be enabled sooner after a cold start.
  • Harsh or soft shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test B .
P0712 P0710, P0712 TFT TFT sensor circuit voltage input too low. TFT sensor input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue).
  • TCC and stabilized shift schedule may be enabled sooner after cold start.
  • Harsh or soft shifts.
  • Will turn on MIL.
 Go to Pinpoint Test B .
P0713 P0710, P0713 TFT TFT sensor circuit voltage too high. TFT sensor input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue).
  • TCC and stabilized shift schedule may be enabled sooner after cold start.
  • Harsh or soft shifts.
  • Will turn on MIL.
 Go to Pinpoint Test B .
P0715 P0715, P0717 Turbine Shaft Speed (TSS) Sensor Insufficient input from TSS sensor.
  • PCM has detected TSS sensor signal failed to 0 speed when vehicle conditions (mainly output speed) indicate TSS sensor output should be present.
  • Electrical failures (open, short) of the TSS sensor wiring, connector or a failure of the sensor itself will cause this failure.
  • Failure Mode Effect Management (FMEM) action opens TSPC (removes power from all solenoids).
    • Provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever).
  • Harsh engagements (due to maximum line pressure).
  • Poor launch performance (due to 5th gear drive away).
  • Will turn on MIL.
 Go to Pinpoint Test C .
P0717 P0717
or
P0715, P0717		 TSS Insufficient input from TSS sensor.
  • PCM has detected TSS sensor signal failed to 0 speed when vehicle conditions (mainly output speed) indicate TSS sensor output should be present.
  • Electrical failures (open, short) of the TSS sensor wiring, connector or a failure of the TSS sensor itself will cause this failure.
  • FMEM action opens TSPC (removes power from all solenoids).
    • Provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever).
  • Harsh engagements (due to maximum line pressure).
  • Poor launch performance (due to 5th gear drive away).
  • Will turn on wrench lamp.
 Go to Pinpoint Test C .
P0718 - TSS TSS signal intermittent. PCM has detected an erratic or no TSS signal. Will turn on wrench lamp. Go to Pinpoint Test C .
P0720 P0720, P0722 Output Shaft Speed (OSS) Sensor Insufficient input from OSS sensor.
  • PCM has detected OSS sensor signal failed to 0 speed when vehicle conditions (mainly turbine speed) indicate OSS sensor output should be present.
  • Electrical failures (open, short) of the OSS sensor wiring, connector or a failure of the OSS sensor itself will cause this failure.
  • FMEM action opens TSPC (removes power from all solenoids).
    • provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever).
  • Harsh engagements (due to maximum line pressure).
  • Poor launch performance (due to 5th drive away).
  • Will turn on MIL.
 Go to Pinpoint Test C .
P0721 - OSS OSS sensor signal noisy. PCM has detected an erratic or no OSS sensor signal. Will turn on wrench lamp. Go to Pinpoint Test C .
P0740 P0740, P0743 TCC Solenoid Electrical Faults TCC circuit is open. Open circuit in solenoid or wiring.
  • TCC failed off - vehicle might run hotter, lose fuel economy.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0742 P0742, P0743 TCC Solenoid Electrical Faults TCC circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL, and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0743 - TCC Solenoid Electrical Faults TCC is open, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0740, P0742 or P0744.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0743 P0740, P0743 TCC Solenoid Electrical Faults TCC circuit is open. Open circuit in solenoid or wiring.
  • TCC failed off - vehicle might run hotter, lose fuel economy.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0743 P0742, P0743 TCC Solenoid Electrical Faults TCC circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL, and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0743 P0743, P0744 TCC Solenoid Electrical Faults TCC is shorted to voltage. Short to power in the wiring or solenoid.
  • TCC failed off - vehicle might run hotter, lose fuel economy.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0744 P0743, P0744 TCC Solenoid Electrical Faults TCC is shorted to voltage. Short to power in the wiring or solenoid.
  • TCC failed off - vehicle might run hotter, lose fuel economy.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0748 - Line Pressure Control (LPC) Solenoid Electrical Faults SSD is open circuit, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0960, P0962 and P0963.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0748 P0748, P0960 LPC Solenoid Electrical Faults SSD circuit is open. Open circuit in solenoid or wiring.
  • Failed to maximum line pressure - harsh engagements.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0748 P0748, P0962 LPC Solenoid Electrical Faults SSD circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • Failed to minimum line pressure.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL, and 5th as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0748 P0748, P0963 LPC Solenoid Electrical Faults SSD is shorted to voltage. Short to power in the wiring or solenoid.
  • Failed to maximum line pressure - harsh engagements.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0750 P0750, P0753 SSA Electrical Faults SSA circuit is open. Open circuit in solenoid or wiring.
  • Forward clutch is failed off - 5th and 6th gears only available forward gears.
  • Neutral condition or flare when fault occurs.
  • Poor launch due to 5th gear drive away.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0753 - SSA Electrical Faults SSA is open, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0750, P0973, P0974.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0753 P0750, P0753 SSA Electrical Faults SSA circuit is open. Open circuit in solenoid or wiring.
  • Forward clutch is failed off - 5th and 6th only available Forward gears.
  • Neutral condition or flare when fault occurs.
  • Poor launch due to 5th gear drive away.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0753 P0750, P0973 SSA Electrical Faults SSA circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL, and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0753 P0750, P0974 SSA Electrical Faults SSA is shorted to voltage. Short to power in the wiring or solenoid.
  • Forward clutch is failed off - 5th and 6th gear only available forward gears.
  • Neutral condition or flare when fault occurs.
  • Poor launch performance (due to 5th gear drive away).
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0755 P0755, P0758 SSB Electrical Faults Open circuit in solenoid or wiring. SSB circuit is open.
  • Direct clutch failed on - only 3rd and 5th gear available.
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0758 - SSB Electrical Faults SSB is open, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0755, P0976, P0977.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0758 P0755, P0758 SSB Electrical Faults Open circuit in solenoid or wiring. SSB circuit is open.
  • Direct clutch failed on - only 3rd and 5th gears available.
  • Harsh engagements.
  • Poor launch performance (due to 3rd gear drive away).
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0758 P0758, P0976 SSB Electrical Faults SSB circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0758 P0758, P0977 SSB Electrical Faults SSB is shorted to voltage. Short to power in the wiring or solenoid.
  • Direct clutch failed on - only 3rd and 5th gear available.
  • Harsh engagements.
  • Poor launch performance (due to 3rd gear drive away).
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0760 P0760, P0763 SSC Electrical Faults SSC circuit is open. Open circuit in solenoid or wiring. Incorrect gear selection depending on condition mode and manual lever position. See solenoid operation LIST.
  • Intermediate clutch is failed off - if fault occurs while in 2nd or 6th gear customer might notice a neutral condition before diagnostics disables 2nd and 6th gear.
  • Customer might notice erratic, delayed or harsh shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0763 - SSC Electrical Faults SSC is open, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0760, P0979, P0980.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0763 P0760, P0763 SSC Electrical Faults SSC circuit is open. Open circuit in solenoid or wiring.
  • Intermediate clutch is failed off - if fault occurs while in 2nd or 6th gears, customer might notice a neutral condition before diagnostics disables 2nd and 6th gears.
  • Customer might notice erratic, delayed or harsh shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0763 P0760, P0797 SSC Electrical Faults SSC circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0763 P0760, P0980 SSC Electrical Faults SSC is shorted to voltage. Short to power in the wiring or solenoid.
  • Intermediate clutch is failed off - if fault occurs while in 2nd or 6th gear, customer might notice a neutral condition before diagnostics disables 2nd and 6th gear.
  • Customer might notice erratic, delayed or harsh shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0765 P0765, P0768 SSD Electrical Faults SSD circuit is open. Open circuit in solenoid or wiring.
  • Overdrive clutch failed on, only 4th, 5th and 6th gears available.
  • Harsh engagements.
  • Poor launch due to 4th gear drive away.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0767 P072F, P073A, P073B, P0767 Overdrive Clutch System Faults (includes non-electrical SSD faults, valve body and clutch) Overdrive clutch failed on (clutch, SSD or valve body). Overdrive clutch failed on, could be due to:
  • Low/reverse clutch/overdrive clutch VFS (SSD) non-electrical failed stuck on (pressure).
  • Overdrive clutch stuck on due to mechanical failure.
  • Low/reverse clutch/overdrive clutch regulator valve stuck in the spring compressed position.
  • Customer may notice a vehicle deceleration on a shift into 2nd or 3rd gears (overdrive clutch failing to release will cause a tie-up in 2nd or 3rd gears).
  • 1st gear with engine braking, 1st gear without engine braking, 2nd and 3rd gears are disabled.
  • Poor Launch due to 4th gear drive away.
  • Harsh engagements.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0768 - SSD Electrical Faults SSD is open, shorted to ground or shorted to voltage. Open, short to ground or short to power in solenoid or wiring.
  • See P0765, P0982, P0983.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0768 P0765, P0768 SSD Electrical Faults SSD circuit is open. Open circuit in solenoid or wiring.
  • Overdrive clutch failed on, only 4th, 5th and 6th gear available.
  • Harsh engagements.
  • Poor launch due to 4th gear drive away.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0768 P0765, P0982 SSD Electrical Faults SSD circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0768 P0765, P0983 SSD Electrical Faults SSD is shorted to voltage. Short to power in the wiring or solenoid.
  • Overdrive clutch failed on, only 4th, 5th and 6th gears available.
  • Harsh engagements, poor launch due to 4th gear drive away.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0770 P0770, P0773 SSE Electrical Faults SSE circuit failure. Open, short to ground or short to power in solenoid or wiring. SSE controls routing SSD pressure to low/reverse clutch or overdrive clutch.
For SSE failed off (no pressure):
  • Customer might notice 4th gear drive away (when 1st gear is commanded).
  • After it is determined on/off is failed to no pressure then 1st gear with engine braking is disabled.
  • Customer may notice nothing or may notice 2nd gear provided when 1st gear selected in low manual lever range.
  • Harsh reverse engagements since low/reverse clutch does not apply in neutral or drive in this failure mode.

For SSE failed on (pressure):
  • High side is turned off.
  • Poor launch performance (due to 5th gear drive away).
  • Harsh engagements.
  • No TCC apply.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0773 P0770, P0773 SSE Electrical Faults SSE circuit failure. Open, short to ground or short to power in solenoid or wiring. SSE controls routing SSD pressure to low/reverse clutch or overdrive clutch.
For SSE failed off (no pressure):
  • Customer might notice 4th gear drive away (when 1st gear commanded).
  • After it is determined on/off is failed to no pressure then 1st gear with engine braking is disabled.
  • Customer may notice nothing or may notice 2nd gear provided when 1st gear selected in low manual lever range.
  • Harsh reverse engagements since low/reverse clutch does not apply in neutral or drive in this failure mode.

For SSE failed on (pressure):
  • High side is turned off.
  • Poor launch performance (due to 5th gear drive away).
  • Harsh engagements.
  • No TCC apply.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0774 - SSE Electrical Faults SSE stuck on or off. See P0771 and P0772.
  • See P0771 and P0772.
  • Will turn on wrench lamp.
 Go to Pinpoint Test A .
P0960 P0960, P0748 LPC Solenoid Electrical Faults SSD circuit is open. Open circuit in solenoid or wiring.
  • Failed to maximum line pressure.
  • Harsh engagements.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0962 P0962, P0748 LPC Solenoid Electrical Faults SSD circuit is shorted to ground. Short to ground in the solenoid or wiring. Failed to minimum line pressure:
  • FMEM action opens the TSPC removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0963 P0963, P0748 LPC Solenoid Electrical Faults SSD is shorted to voltage. Short to power in the wiring or solenoid.
  • Failed to maximum line pressure.
  • Harsh engagements.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0973 P0973, P0753 SSA Electrical Faults SSA circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0974 P0974, P0753 SSA Electrical Faults SSA is shorted to voltage. Short to power in the wiring or solenoid.
  • Forward clutch is failed off - 5th and 6th gears only available forward gears.
  • Neutral condition or flare when fault occurs.
  • Poor launch due to 5th gear drive away
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0976 P0976, P0758 SSB Electrical Faults SSB circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0977 P0977, P0758 SSB Electrical Faults SSB is shorted to voltage. Short to power in the wiring or solenoid.
  • Direct clutch failed on - only 3rd and 5th gear available.
  • Harsh engagements.
  • Poor launch due to 3rd gear drive away.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0979 P0979, P0763 SSC Electrical Faults SSC circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open).
  • Harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0980 P0980, P0763 SSC Electrical Faults SSC is shorted to voltage. Short to power in the wiring or solenoid. Intermediate clutch is failed off:
  • If fault occurs while in 2nd or 6th gear, customer might notice a neutral condition before diagnostics disables 2nd and 6th gears.
  • Customer might notice erratic, delayed or harsh shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0982 P0982, P0768 SSD Electrical Faults SSD circuit is shorted to ground. Short to ground in the solenoid or wiring.
  • FMEM action opens the TSPC removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th as the only forward gear with TCC open), harsh engagements.
  • Poor launch performance (due to 5th gear drive away).
  • No TCC apply.
  • No shifts.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P0983 P0983, P0768 SSD Electrical Faults SSD is shorted to voltage. Short to power in the wiring or solenoid.
  • Overdrive clutch failed on, only 4th, 5th and 6th gears available.
  • Harsh engagements.
  • Poor launch due to 4th gear drive away.
  • Will turn on MIL.
 Go to Pinpoint Test A .
P1702 - TR Sensor Electrical Faults TR sensor circuit failure. P1702 - see P0705 and P0708.
  • Possible no crank, only PARK, REVERSE, NEUTRAL and 5th gear available, harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened - harsh engagements, poor performance (due to a 5th gear drive away), no shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test D .
P1702 P0705, P1702 TR Sensor TR sensor circuit failure. PCM is received an invalid combination of the 4-bit signal from the TR sensor (wiring, connector or TR sensor issue).
  • Possible no crank, only PARK, REVERSE, NEUTRAL and 5th gear available, harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened - harsh engagements, poor performance (due to a 5th gear drive away), no shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test D .
P1702 P0708, P1702 TR Sensor TR sensor circuit failure. PCM is received all 4 TR sensor bits open (potential sensor disconnected, wiring, connector or TR sensor issue).
  • Possible no crank, only PARK, REVERSE, NEUTRAL and 5th gear available, harsh engagements.
  • Extremely delayed engagements (until a DTC is set).
  • After a DTC is set and the high side opened - harsh engagements, poor performance (due to a 5th gear drive away), no shifts.
  • Will turn on wrench lamp.
 Go to Pinpoint Test D .
P1705 - TR Sensor TR sensor. TR sensor not indicating Park or Neutral during KOEO or KOER self-test. Carry out KOEO or KOER only. Go to Pinpoint Test D .
P1711 - TFT TFT sensor. TFT out of self-test range (less than -1°C [30°F] or greater than 105°C [220°F]). Carry out KOEO or KOER only. Go to Pinpoint Test B .
scientia non olet · About LEMON Manuals