LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2007 >> Expedition RWD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission External Controls >> Removal And Installation >> Selector Lever Mechanism >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Selector Lever Mechanism: Installation

  1. Install the BSIA onto the selector lever mechanism.
    1. Pull the BSIA override button.
    2. Align the selector lever tab into the BSIA.
    3. Position and secure the BSIA with the clip.
    4. Install the screw.
    2. Fig 1: Brake Shift Interlock Actuator (BSIA), Button & Screw
    GF0022897Courtesy of FORD MOTOR CO.
  2. Install the selector lever mechanism into the vehicle, install the upper bolts and connect the BSIA electrical connector.
    • Tighten to 6 Nm (53 lb-in).
    3. Fig 2: Brake Shift Interlock Actuator (BSIA), Electrical Connector & Bolts
    GF0022895Courtesy of FORD MOTOR CO.
  3. Install the selector lever mechanism lower bolt.
    • Tighten to 6 Nm (53 lb-in).
    4. Fig 3: Selector Lever Mechanism Lower Bolt
    GF0022894Courtesy of FORD MOTOR CO.
  4. Install the selector lever.
    • Tighten to 18 Nm (13 lb-ft).
    5. Fig 4: Selector Lever Bolt
    GF0022881Courtesy of FORD MOTOR CO.
  5. Connect the TC switch electrical connector and the harness into the retaining clips.
    6. Fig 5: Electrical Connector & Retaining Clips
    GF0022880Courtesy of FORD MOTOR CO.
  6. Install the locking pin and the PLC.
    1. Connect the PLC.
    2. Install a new locking pin.
    7. Fig 6: Park Lock Cable (PLC) & Locking Pin
    GF0022898Courtesy of FORD MOTOR CO.
    CAUTION: To prevent cable damage, do not apply force to the selector lever cable assembly between the steering column selector lever arm and the steering column bracket.
  7. Connect the selector lever cable.
    8. Fig 7: Selector Lever Cable
    GF0022892Courtesy of FORD MOTOR CO.
  8. Position the IP cluster and install the LH lower IP cluster screw.
    9. Fig 8: Left Lower IP Cluster Screw
    GF0022891Courtesy of FORD MOTOR CO.
  9. Install the RH lower IP cluster screw.
    10. Fig 9: Right Lower IP Cluster Screw
    GF0022890Courtesy of FORD MOTOR CO.
  10. Install the upper IP cluster screws.
    11. Fig 10: Upper IP Cluster Screws
    GF0022889Courtesy of FORD MOTOR CO.
  11. Position the IP cluster trim and connect the dimmer switch electrical connector.
    12. Fig 11: Dimmer Switch Electrical Connector
    GF0022888Courtesy of FORD MOTOR CO.
  12. If equipped, connect the in-vehicle temperature sensor connector.
    13. Fig 12: In-Vehicle Temperature Sensor Connector
    GF0022887Courtesy of FORD MOTOR CO.
  13. Install the LH IP cluster trim screw.
    14. Fig 13: Left IP Cluster Trim Screw
    GF0022886Courtesy of FORD MOTOR CO.
  14. Install the RH IP cluster trim screw.
    15. Fig 14: Right IP Cluster Trim Screw
    GF0022885Courtesy of FORD MOTOR CO.
  15. Install the IP cluster-to-shroud trim.
    16. Fig 15: IP Cluster-To-Shroud Trim
    GF0022884Courtesy of FORD MOTOR CO.
  16. Install the steering column upper shroud.
  17. Install the steering column lower shroud.
    1. Install the screws and the lower shroud.
    18. Fig 16: Lower Steering Column Shroud
    GF0022861Courtesy of FORD MOTOR CO.
  18. Install the instrument panel lower finish panel.
    19. Fig 17: Lower Steering Column Opening Cover Screws
    GF0021867Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals