Restraints Control Module (RCM) DTC Chart

DTC	Description	Action To Take
Continuous lamp	The Air Bag Indicator is Illuminated Continuously	GO to PINPOINT TEST A .
B1085	Restraint System - Seatbelt Load Limiter Status	GO to PINPOINT TEST B .
B1118	Passenger Front Crash Sensor Mount/Communication Fault (RH front impact severity sensor)	GO to PINPOINT TEST C .
B1135	Passenger Front Crash Sensor Internal Fault (RH front impact severity sensor)	INSTALL a new passenger front crash sensor. REFER to FRONT IMPACT SEVERITY SENSOR .
B1231	Event Threshold Exceeded	INSTALL a new Restraints Control Module (RCM) and impact sensors. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT .
B1317	Battery Voltage High	GO to PINPOINT TEST AB .
B1318	Battery Voltage Low	GO to PINPOINT TEST AB .
B1342	ECU is Faulted	INSTALL a new RCM . REFER to RESTRAINTS CONTROL MODULE (RCM) .
B1884	PAD Warning Lamp Circuit Failure	GO to PINPOINT TEST D .
B1890	PAD Warning Lamp Circuit Short to Battery	GO to PINPOINT TEST E .
B2290	Occupant Classification System Fault	NOTE: If no on-demand or continuous DTC is present in the Occupant Classification System Module (OCSM) and DTC B2290 is only present in the RCM as a continuous DTC, CLEAR all RCM DTCs and PROVE OUT the Supplemental Restraint System (SRS). The OCSM reported a fault message to the RCM . CARRY OUT self test of the OCSM and RETRIEVE continuous DTCs.
B2292	Restraint System - Seatbelt Pretensioner Fault	GO to PINPOINT TEST G .
B2293	Restraint System - Air Bag Fault	GO to PINPOINT TEST H .
B2294	Restraint System - Curtain Fault	GO to PINPOINT TEST I .
B2295	Restraint System - Side Air Bag Fault	GO to PINPOINT TEST J .
B2296	Restraint System - Impact Sensor Fault	GO to PINPOINT TEST K .
B2434	Drivers Seat Belt Buckle Switch Circuit Short to Ground	GO to PINPOINT TEST L .
B2435	Drivers Seat Belt Buckle Switch Resistance Out of Range	GO to PINPOINT TEST M .
B2438	Passengers Seat Belt Buckle Switch Short to Ground	GO to PINPOINT TEST N .
B2439	Passengers Seat Belt Buckle Switch Resistance Out of Range	GO to PINPOINT TEST O .
B2477	Module Configuration Failure	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. CARRY OUT Programmable Module Installation (PMI). REFER to MODULE CONFIGURATION .
B2607	Harness/Configuration Mismatch	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. CARRY OUT Programmable Module Installation (PMI). REFER to MODULE CONFIGURATION .
B2691	Seat Belt Buckle Switch Circuit Fault, Front Driver's Side	GO to PINPOINT TEST P .
B2692	Front Passenger's Seat Belt Buckle Switch Circuit Fault	GO to PINPOINT TEST Q .
B2792	Cross Link Between Firing Loops	GO to PINPOINT TEST R .
B2984	Deployable Steering Column Circuit Open	GO to PINPOINT TEST S .
B2985	Deployable Steering Column Circuit Short to Battery	GO to PINPOINT TEST T .
B2986	Deployable Steering Column Circuit Short to Ground	GO to PINPOINT TEST U .
B2987	Deployable Steering Column Circuit Resistance Low on Squib	GO to PINPOINT TEST S .
C1414	Incorrect Module Design Level	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. CARRY OUT Programmable Module Installation (PMI). REFER to MODULE CONFIGURATION .
C1946	Front Driver's Seat Track Position Switch Circuit Open	GO to PINPOINT TEST X .
C1947	Front Driver's Seat Track Position Switch Circuit Short to Ground	GO to PINPOINT TEST Y .
C1948	Front Driver's Seat Track Position Switch Circuit Resistance Out of Range	GO to PINPOINT TEST Z .
C1981	Front Driver's Seat Track Position Switch Circuit Fault	GO to PINPOINT TEST AA .
U0300	Internal Control Module Software Incompatibility	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. CARRY OUT Programmable Module Installation (PMI). REFER to MODULE CONFIGURATION .
U1900	CAN Communication Bus Fault - Receive Error	NOTE: DTC U1900 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair for a RCM DTC U1900 fault. VIEW and RECORD IC_MSG_ RCM , PCM_MSG_ RCM and OCS _MSG_ RCM fault PIDs to determine the module with the concern. REFER to MODULE COMMUNICATIONS NETWORK to diagnose the High Speed Controller Area Network (HS-CAN)/module concern.
U2050	No Application Present	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. INSTALL a new RCM . REFER to RESTRAINTS CONTROL MODULE (RCM) .
U2051	One or More Calibration Files Missing/Corrupt	NOTE: When installing a new RCM , always make sure the correct RCM is being installed. If an incorrect RCM is installed, DTCs will result. CARRY OUT Programmable Module Installation (PMI). REFER to MODULE CONFIGURATION .