Smart Junction Box (SJB) DTC Chart
SMART JUNCTION BOX (SJB) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B106E | Solid State Driver Disabled Due to Short Circuit | The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Smart Junction Box (SJB) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test. |
| B106F | Module Disabled Due to External Fault | The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the SJB can withstand. The cause of the excessive current draw MUST be corrected before a new SJB is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new SJB . REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |
| B1472 | Lamp Headlamp Input Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1485 | Brake Pedal Input Short to Battery | GO to PINPOINT TEST I . |
| B1510 | Flash To Pass Switch Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1578 | Lamp Park Input Circuit Short to Ground | GO to PINPOINT TEST O . |
| B2044 | Left Rear Stop Lamp Circuit Short to Ground | GO to PINPOINT TEST H . |
| B2045 | Left Rear Stop Lamp Circuit Open | If the lamp is inoperative, VERIFY the bulb is OK. If OK, GO to PINPOINT TEST H
. If the lamp is always on, GO to PINPOINT TEST I . |
| B2046 | Right Rear Stop Lamp Circuit Short to Ground | GO to PINPOINT TEST H . |
| B2047 | Right Rear Stop Lamp Circuit Open | If the lamp is inoperative, VERIFY the bulb is OK. If OK, GO to PINPOINT TEST H
. If the lamp is always on, GO to PINPOINT TEST I . |
| B2048 | Left Rear Turn Lamp Circuit Short to Ground | GO to PINPOINT TEST L . |
| B2049 | Left Rear Turn Lamp Circuit Open | VERIFY the bulb is OK. If OK, GO to PINPOINT TEST L . |
| B2050 | Right Rear Turn Lamp Circuit Short to Ground | GO to PINPOINT TEST L . |
| B2051 | Right Rear Turn Lamp Circuit Open | VERIFY the bulb is OK. If OK, GO to PINPOINT TEST L . |
| B2071 | Hazard Switch Signal Short to Ground | GO to PINPOINT TEST M . |
| B2281 | Right Turn Switch Short to Ground | GO to PINPOINT TEST K . |
| B2282 | Left Turn Switch Short to Ground | GO to PINPOINT TEST K . |
| B2498 | Headlamp Switch Multiple Signals Input Active | ADDRESS any other DTCs first. GO to PINPOINT TEST D . |
| B2A22 | Headlamp Off Circuit Open | GO to PINPOINT TEST D . |
| B2A23 | High Beam Input Circuit Short to Ground | GO to PINPOINT TEST E . |
| B2A24 | Turn Signal Input Circuit Failure | ADDRESS any other DTCs first. If no other DTCs are present, GO to SYMPTOM CHART . |
| B2A27 | Right Front Turn Lamp Circuit Open | VERIFY the bulb is OK. If OK, GO to PINPOINT TEST L . |
| B2A28 | Right Front Turn Lamp Circuit Short to Ground | GO to PINPOINT TEST L . |
| B2A29 | Left Front Turn Lamp Circuit Open | VERIFY the bulb is OK. If OK, GO to PINPOINT TEST L . |
| B2A2A | Left Front Turn Lamp Circuit Short to Ground | GO to PINPOINT TEST L . |
| B2A2B | Left Corner Lamp Output Circuit Short to Ground | DIAGNOSE all other DTCs and symptoms first. If no other DTCs or symptoms are present, INSPECT the SJB and C2280f for bent pins, loose or corroded connections. If no concerns are found, INSTALL a new SJB . REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |
| B2A2C | Right Corner Lamp Output Circuit Short to Ground | DIAGNOSE all other DTCs and symptoms first. If no other DTCs or symptoms are present, INSPECT the SJB and C2280f for bent pins, loose or corroded connections. If no concerns are found, INSTALL a new SJB . REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |
| B2A2E | Right Front Lamp Low Beam Circuit Open | If the low beam is inoperative, VERIFY the bulb is OK. If OK, GO to PINPOINT TEST B
. If the low beam is always on, GO to PINPOINT TEST D . |
| B2A2F | Right Front Lamp Low Beam Circuit Short to Ground | GO to PINPOINT TEST B . |
| B2A30 | Left Front Lamp Low Beam Circuit Open | If the low beam is inoperative, VERIFY the bulb is OK. If OK, GO to PINPOINT TEST B
. If the low beam is always on, GO to PINPOINT TEST D . |
| B2A31 | Left Front Lamp Low Beam Circuit Short to Ground | GO to PINPOINT TEST B . |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |