Audio Control Module (ACM) - With Navigation DTC Chart
AUDIO CONTROL MODULE (ACM) - WITH NAVIGATION DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST I . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST I . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST L . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST L . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A56:21 | Antenna: Signal Amplitude □ Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST P . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST P . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D78:13 | Auxiliary Input: Circuit Open | GO to PINPOINT TEST H . |
| B1D79:01 | Microphone Input Circuit: General Electrical Failure | GO to PINPOINT TEST N . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to PARKING AID -- E-SERIES . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST X . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | GO to PINPOINT TEST Z . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST K . |
| U197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AD . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| U2014:09 | Control Module Hardware: Component Failure | GO to PINPOINT TEST J . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST R . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | PROGRAM the ACM . REFER to PMI in MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the ACM . REFER to PMI in MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the ACM . REFER to PMI in MODULE CONFIGURATION . |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new ACM . REFER to AUDIO CONTROL MODULE (ACM) . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AE . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AF . |