LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2011 >> Fiesta S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 13 (Module Communications Network) >> Diagnosis And Testing >> Communications Network >> Inspection and Verification
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection and Verification

WARNING: This page is about a different car, the 2012 Ford Fiesta. However, it is still accessible from the selected car via links, so may be relevant.
  1. Verify the customer concern.
  2. Visually inspect for obvious signs of electrical damage.
    • If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
    VISUAL INSPECTION CHART

    Electrical
    • Battery Junction Box (BJB) fuse(s):
      • 1 (40A) (ABS module)
      • 2 (50A) (Transmission Control Module (TCM))
      • 9 (20A) (ABS module)
      • 22 (15A) (PCM)
      • 32 (7.5A) (PCM, TCM)
    • Central Junction Box (CJB) fuse(s):
      • 1 (15A) (Remote Function Actuator (RFA) module)
      • 3 (7.5A) (Instrument Panel Cluster (IPC))
      • 4 (7.5A) (Occupant Classification System Module (OCSM))
      • 5 (15A) (no power to scan tool)
      • 7 (7.5A) (Front Control/Display Interface Module (FCDIM))
      • 9 (20A) (RFA module)
      • 10 (15A) (Audio Front Control Module (ACM), Accessory Protocol Interface Module (APIM), Global Positioning System Module (GPSM))
      • 12 (20A) (Tire Pressure Monitor (TPM) /Vehicle Security Module (VSM))
      • 14 (20A) (RFA module)
      • 19 (7.5A) (ACM, IPC)
      • 20 (10A) (Restraints Control Module (RCM))
      • 21 (10A) (Body Control Module (BCM), IPC, Power Steering Control Module (PSCM))
      • 22 (7.5A) (ABS module, PCM)
      • 23 (10A) (TCM, TPM/VSM)
      • 26 (7.5A) (TPM/VSM)
    • Data Link Connector (DLC)
    • Wiring, terminals or connectors
  3. Connect the scan tool to the DLC.
      NOTE: Make sure to use the latest scan tool software release.
      NOTE: The Vehicle Communication Module (VCM) LED prove-out confirms power and ground from the DLC are provided to the VCM.
    • If the Integrated Diagnostic System (IDS) does not communicate with the VCM :
      • Check the VCM connection to the vehicle.
      • Check the scan tool connection to the VCM.
      • GO to Pinpoint Test R , to diagnose No Power To The Scan Tool.
  4. Establish a scan tool session.
      NOTE: The scan tool first attempts to communicate with the PCM, after establishing communication with the PCM, the scan tool then attempts to communicate with all other modules on the vehicle.
    • If an IDS session cannot be established with the vehicle, (IDS may state "No communication can be established with the PCM"):
      • Choose "NO" when the scan tool prompts whether or not to retry communication.
      • Enter either a PCM part number, tear tag or calibration number to identify the vehicle and start a session (the PCM part number and 4-character tear tag are printed on the PCM label).
      • GO to Pinpoint Test A , to diagnose The PCM Does Not Respond To The Scan Tool.
  5. Carry out the network test.
    • If the network test passes, retrieve and record the continuous memory DTCs and proceed to Step 6.
    • If the network test fails, GO to Symptom Chart  to diagnose the failed communication network.
    • If a module fails to communicate during the network test, GO to Symptom Chart .
  6. Retrieve and review the DTCs.
    • If the DTCs retrieved are related to the concern, go to DTC Charts . Follow the non-network DTC diagnostics (B-codes, C-codes, P-codes) prior to the network DTC diagnostics (U-codes).
    • If no DTCs related to the concern are retrieved, GO to Symptom Chart .
scientia non olet · About LEMON Manuals