LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2011 >> Fiesta SES, Automatic DCT >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Automatic Transaxle/Transmission DTCS
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Automatic Transaxle/Transmission DTCS

AUTOMATIC SHIFTING MANUAL TRANSMISSION/TRANSAXLE DIAGNOSTIC TROUBLE CODE (DTC) LIST

Five Digit DTC Description Action
C0044:28 Brake pressure sensor A: signal bias level out of range/zero adjustment failure For additional information, refer to VEHICLE DYNAMIC SYSTEMS .
P06A6 Sensor reference voltage A circuit range/performance Go to PINPOINT TEST C .
P06A7 Sensor reference voltage B circuit range/performance Go to PINPOINT TEST C .
P06A8 Sensor reference voltage C circuit range/performance Go to PINPOINT TEST C .
P0701 Wrong engine control fault - monitors the torque up and engine speed requests from the Transmission Control Module (TCM), if it finds a fault it turns off these requests See more specific DTC. If no other DTCs are set, clear code and re-test.
P0702 Transmission control system electrical Adjust selector lever cable. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS . If concern still present, replace TR  sensor.
P0706 TR  sensor A circuit range/performance Go to PINPOINT TEST D .
P0707 TR  sensor A circuit low Adjust selector lever cable. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS . If concern still present, replace TR sensor.
P0708 TR  sensor A circuit high Go to PINPOINT TEST D .
P0709 TR  sensor A circuit intermittent Go to PINPOINT TEST D .
P0715 Insufficient input from input shaft speed sensor Go to PINPOINT TEST C .
P0716 Input shaft speed sensor A circuit Go to PINPOINT TEST C .
P0717 Input shaft speed sensor A circuit no signal Go to PINPOINT TEST C .
P0718 Input shaft speed sensor A signal intermittent Go to PINPOINT TEST C .
P0720 Insufficient input from OSS  sensor circuit Go to PINPOINT TEST C .
P0721 OSS  sensor signal error Go to PINPOINT TEST C .
P0722 OSS  sensor no signal Go to PINPOINT TEST C .
P0723 OSS  sensor circuit intermittent Go to PINPOINT TEST C .
P072B Stuck in reverse
  • REPAIR all speed sensor, clutch motor 2, and clutch 2 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM Shift Motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P072C Stuck in gear 1
  • REPAIR all speed sensor, clutch motor 1, and clutch 1 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P072D Stuck in gear 2
  • REPAIR all speed sensor, clutch motor 2, and clutch 2 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P072E Stuck in gear 3
  • REPAIR all speed sensor, clutch motor 1, and clutch 1 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P072F Stuck in gear 4
  • REPAIR all speed sensor, clutch motor 2, and clutch 2 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P073A Stuck in gear 5
  • REPAIR all speed sensor, clutch motor 1, and clutch 1 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P073B Stuck in gear 6
  • REPAIR all speed sensor, clutch motor 2, and clutch 2 performance DTCs first.
  • Go to PINPOINT TEST B .
  • INSPECT shift drum, shift fork, synchronizer and TCM  shift motors for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P073E Unable to engage reverse INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P073F Unable to engage gear 1 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P074A Unable to engage gear 2 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P074B Unable to engage gear 3 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P074C Unable to engage gear 4 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P074D Unable to engage gear 5 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P074E Unable to engage gear 6 INSPECT shift fork and synchronizer for wear or damage. REPLACE as needed. Refer to TRANSAXLE in this information.
P07A2 Transmission friction element A performance/stuck off Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P07A3 Transmission friction element A stuck on Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P07A4 Transmission friction element B performance/stuck off Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P07A5 Transmission friction element B stuck on Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P0805 Clutch position sensor A circuit Go to PINPOINT TEST A .
P0806 Clutch position sensor A circuit range/performance Go to PINPOINT TEST A .
P0809 Clutch position sensor A circuit intermittent Go to PINPOINT TEST A .
P087A Clutch position sensor B circuit Go to PINPOINT TEST A .
P087B Clutch position sensor B circuit range/performance Go to PINPOINT TEST A .
P087E Clutch position sensor B circuit intermittent Go to PINPOINT TEST A .
P0882 TCM  power input signal low Go to PINPOINT TEST A .
P0883 TCM  power input signal high CHARGING SYSTEM .
P0900 Clutch A actuator control circuit/open Go to PINPOINT TEST A .
P0901 Clutch A actuator control circuit range/performance Go to PINPOINT TEST A .
P0902 Clutch A actuator control circuit low Go to PINPOINT TEST A .
P0903 Clutch A actuator control circuit high Go to PINPOINT TEST A .
P090A Clutch B actuator control circuit/open Go to PINPOINT TEST A .
P090B Clutch B actuator control circuit performance Go to PINPOINT TEST A .
P090C Clutch B actuator control circuit low Go to PINPOINT TEST A .
P090D Clutch B Actuator Control Circuit High Go to PINPOINT TEST A .
P163E TCM  programming error Refer to TRANSMISSION CONTROL MODULE (TCM) ADAPTIVE LEARNING in this information.
P2700 Transmission friction element A apply time range/performance Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P2701 Transmission friction element B apply time range/performance Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P2765 Input speed sensor 2 circuit Go to PINPOINT TEST C .
P2766 Input speed sensor 2 circuit range/performance Go to PINPOINT TEST C .
P2767 Input speed sensor 2 circuit no signal Go to PINPOINT TEST C .
P2768 Input speed sensor 2 circuit intermittent Go to PINPOINT TEST C .
P2801 TR  sensor B circuit range/performance Go to PINPOINT TEST D .
P2802 TR  sensor B circuit low Go to PINPOINT TEST D .
P2803 TR  sensor B circuit high Go to PINPOINT TEST D .
P2804 TR  sensor B circuit intermittent Go to PINPOINT TEST D .
P2805 TR  sensor A/B correlation Go to PINPOINT TEST D .
P2831 Shift fork A position circuit intermittent Go to PINPOINT TEST B .
P2832 Shift fork A position circuit range/performance Go to PINPOINT TEST B .
P2835 Shift fork A position circuit intermittent Go to PINPOINT TEST B .
P2836 Shift fork B position circuit Go to PINPOINT TEST B .
P2837 Shift fork B position circuit range/performance Go to PINPOINT TEST B .
P283A Shift fork B position circuit intermittent Go to PINPOINT TEST B .
P285B Shift fork A actuator circuit/open Go to PINPOINT TEST B .
P285C Shift fork A actuator circuit performance Go to PINPOINT TEST B .
P285D Shift fork A actuator circuit low Go to PINPOINT TEST B .
P285E Shift fork A actuator circuit high Go to PINPOINT TEST B .
P285F Shift fork B actuator circuit/open Go to PINPOINT TEST B .
P2860 Shift fork B actuator circuit performance Go to PINPOINT TEST B .
P2861 Shift fork B actuator circuit low Go to PINPOINT TEST B .
P2862 Shift fork B actuator circuit high Go to PINPOINT TEST B .
P286F Clutch A disengagement time performance/too slow Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P2872 Clutch A stuck engaged
  • Go to PINPOINT TEST B .
  • Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P2877 Clutch B disengagement time performance/too slow Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P287A Clutch B stuck engaged
  • Go to PINPOINT TEST B .
  • Check the clutch for wear or damage. For additional information, refer to CLUTCH in this information.
P287B Shift fork calibration not learned Refer to TRANSMISSION CONTROL MODULE (TCM) ADAPTIVE LEARNING in this information.
U0028 Vehicle communication bus A Refer to MODULE COMMUNICATIONS NETWORK .
U0073 Control module communication bus A off Refer to MODULE COMMUNICATIONS NETWORK .
U0100 Lost communication with Engine Control Module (ECM)/PCM  A Refer to MODULE COMMUNICATIONS NETWORK .
U0115 Lost Communication With ECM  /PCM  B Refer to MODULE COMMUNICATIONS NETWORK .
U0121 Lost communication with ABS  control module Refer to MODULE COMMUNICATIONS NETWORK .
U0129 Lost communication with ABS  control module Refer to MODULE COMMUNICATIONS NETWORK .
U0140 Lost communication with Body Control Module (BCM) Refer to MODULE COMMUNICATIONS NETWORK .
U0141 Lost communication with BCM  A Refer to MODULE COMMUNICATIONS NETWORK .
U0155 Lost communication with Instrument Panel Cluster (IPC) control module Refer to MODULE COMMUNICATIONS NETWORK .
U0294 Lost communication with PCM  Refer to the ELECTRONIC ENGINE CONTROLS .
U0401 Invalid data received from ECM  /PCM  A Refer to the ENGINE EMISSION CONTROL .
U0415 Invalid data received from ABS  control module Refer to VEHICLE DYNAMIC SYSTEMS .
scientia non olet · About LEMON Manuals