Automatic Transaxle/Transmission - 6F35 DTCS

DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC	Grouping	Component	Description	Condition	Symptom	Action
P0657	-	Transaxle solenoid power control	Actuator supply voltage A circuit/open	Transaxle solenoid power control provides power to all the solenoids. This DTC sets if the transaxle solenoid power control relay circuit is open.	Harsh engagements. No voltage to solenoids. Maximum line pressure. Only PARK, REVERSE, NEUTRAL and 5th gear available. No Torque Converter Clutch (TCC). Poor launch due to 5th gear drive away. Will turn on Malfunction Indicator Lamp (MIL).	GO to PINPOINT TEST E .
P0701	P2700 (Forward Clutch), P2701 (Direct Clutch), P2702 (Intermediate Clutch), P2703 (Low/ Reverse Clutch) and P2704 (Overdrive Clutch)	Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)).	Transmission control system range/ performance	The PCM has detected an intermittent clutch on fault and the control system keeps getting stuck on ratio changes but when it turns off the suspected clutch it releases. No stuck on DTCs set.	Vehicle decelerates during upshifts or hangs in gear Will turn on wrench lamp.	Non-electrical failure. REPAIR the more specific DTC first. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0706	P1702, P1921	TR sensor	TR sensor A circuit range/ performance.	TR sensor frequency out of range. PCM receives a duty cycle at 125 Hz. If the frequency is out of range (75 to 175 Hz is the acceptable range) this DTC will set. Possible wiring, connector or TR sensor issue.	Possible no crank. Only PARK, REVERSE, NEUTRAL and 5th gear available. Harsh engagements. Extremely delayed engagements (until a DTC is set). After a DTC is set and the high side opened. Harsh engagements. Poor performance (due to a 5th gear drive away). No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST D .
P0707	P1702, P1921	TR sensor	TR sensor A circuit low.	TR sensor circuit duty cycle out of range, low. TR sensor duty cycle below the minimum value for park (possible open circuit, short to ground, wiring, connector or TR sensor issue).	Possible no crank. Only PARK, REVERSE, NEUTRAL and 5th gear available. Harsh engagements. Extremely delayed engagements (until a DTC is set). After a DTC is set and the high side opened. Harsh engagements. Poor performance (due to a 5th gear drive away). No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST D .
P0708	P1702, P1921	TR sensor	TR sensor A circuit high.	TR sensor duty cycle duty cycle out of range, high. Duty cycle above the maximum value for LOW (possible short to power, wiring, connector or TR sensor issue).	Possible no crank. Only PARK, REVERSE, NEUTRAL and 5th gear available. Harsh engagements. Extremely delayed engagements (until a DTC is set). After a DTC is set and the high side opened. Harsh engagements. Poor performance (due to a 5th gear drive away). No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST D .
P0710	P0711, P0712, P0713	Transmission Fluid Temperature (TFT) sensor	TFT sensor A circuit	TFT sensor voltage input too low or too high. TFT input indicates a short to ground or an open circuit (could be a wiring, connector or sensor issue). Also see P0711, P0712 and P0713.	TCC and stabilized shift schedule may be enabled sooner after cold start. Harsh or soft shifts. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST B .
P0711	-	TFT sensor	TFT sensor A circuit range/ performance.	PCM has detected no TFT sensor change during operation.	TCC and stabilized shift schedule may be enabled sooner after a cold start. Harsh or soft shifts. Will turn on wrench lamp.	GO to PINPOINT TEST B .
P0712	P0710, P0712	TFT sensor	TFT sensor A circuit low.	The PCM has detected a voltage drop across the TFT sensor exceeds a temperature greater than 171°C (340°F) for more then 2.5 seconds (grounded circuit).	TCC and stabilized shift schedule may be enabled sooner after cold start. Harsh or soft shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST B .
P0713	P0710, P0713	TFT sensor	TFT sensor A circuit high.	The PCM has detected a voltage drop across the TFT sensor exceeds a temperature less than -45°C (-50°F) for more then 2.5 seconds (open circuit).	TCC and stabilized shift schedule may be enabled sooner after cold start. Harsh or soft shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST B .
P0715	P0717	Turbine Shaft Speed (TSS) sensor	TSS sensor A circuit.	PCM has detected TSS sensor signal failed to 0 speed when vehicle conditions (mainly output speed) indicate TSS sensor output should be present. Electrical failures (open, short) of the TSS sensor wiring, connector or a failure of the sensor itself will cause this failure.	Failure Mode Effect Management action opens transaxle solenoid power control (removes power from all solenoids). Provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever). Harsh engagements (due to maximum line pressure). Poor launch performance (due to 5th gear drive away). Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST F .
P0717	P0715	TSS sensor	TSS sensor A circuit no signal.	Non-MIL sister code to P0715. Used to illuminate the wrench light.	Failure Mode Effect Management action opens transaxle solenoid power control (removes power from all solenoids). Provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever). Harsh engagements (due to maximum line pressure). Poor launch performance (due to 5th gear drive away).	REPAIR the more specific DTC first. GO to PINPOINT TEST F .
P0718	-	TSS sensor	TSS sensor A circuit intermittent.	PCM has detected an erratic or noisy TSS sensor signal.	Will turn on wrench lamp.	GO to PINPOINT TEST F .
P0720	P0722	Output Shaft Speed (OSS) sensor	OSS sensor circuit.	PCM has detected OSS sensor signal failed to 0 speed when vehicle conditions (mainly turbine speed) indicate OSS sensor output should be present. Electrical failures (open, short) of the OSS sensor wiring, connector or a failure of the OSS sensor itself will cause this failure.	Failure Mode Effect Management action opens transaxle solenoid power control (removes power from all solenoids). provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever). Harsh engagements (due to maximum line pressure). Poor launch performance (due to 5th drive away). Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST C .
P0721	-	OSS sensor	OSS sensor circuit range/ performance.	PCM has detected an erratic or noisy OSS sensor signal.	Will turn on wrench lamp.	GO to PINPOINT TEST C .
P0722	P0720	OSS sensor	OSS sensor circuit no signal.	Non-MIL sister code to P0720. Used to illuminate the wrench light.	Failure Mode Effect Management action opens transaxle solenoid power control (removes power from all solenoids). Provides PARK, REVERSE, NEUTRAL and 5th gear with maximum line pressure and open TCC available (controlled by the manual lever). Harsh engagements (due to maximum line pressure). Poor launch performance (due to 5th gear drive away).	REPAIR the more specific DTC first. GO to PINPOINT TEST C .
P0729	-	Transaxle	Gear 6 incorrect ratio	The PCM did not detect a 6th gear ratio. Shift Solenoid C (SSC) and/or Shift Solenoid D (SSD) stuck off non-electrical fault (no pressure). Low/reverse clutch and/or overdrive clutch regulator valve stuck in default position. Low/reverse clutch and/or overdrive clutch boost valve stuck in default position.	Customer may notice flares or neutral conditions on shifts. Erratic shifting, flares, neutral conditions while the code is being set. 6th gear disabled. Will turn on MIL. TCIL flashing Will turn on wrench lamp.	Intermediate (2,6) clutch or overdrive (4,5,6) clutch slip or failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0731	-	Transaxle	Gear 1 incorrect ratio	Forward clutch, low/reverse clutch or One- Way Clutch (OWC) failed to apply. Shift Solenoid A (SSA) and/or SSD stuck off non-electrical fault (no pressure). Forward clutch and/or low/ reverse clutch regulator valve stuck in default position. Forward clutch and/or low/ reverse clutch boost valve stuck in default position.	Customer might notice flares or neutral conditions, hangs in gear. Disable 1st gear. No engine braking. Will turn on wrench lamp.	Forward (1,2,3,4) clutch, low/reverse (L,R) clutch or OWC slip or failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0732	-	Transaxle	Gear 2 incorrect ratio	Forward clutch or intermediate clutch failed to apply. SSA and/or SSC stuck off non-electrical fault (no pressure). Forward clutch and/or intermediate clutch regulator valve stuck in default position. Forward clutch and/or intermediate clutch boost valve stuck in default position.	Customer might notice flares or neutral conditions, hangs in gear. Disable 2nd gear. Will turn on wrench lamp.	Forward (1,2,3,4) clutch, or intermediate (2,6) clutch failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0733	-	Transaxle	Gear 3 incorrect ratio	Forward clutch or direct clutch failed to apply. SSA and/or Shift Solenoid B (SSB) stuck off non-electrical fault (no pressure). Forward clutch and/or direct clutch regulator valve stuck in default position. Forward clutch and/or direct clutch boost valve stuck in default position.	Customer might notice flares or neutral conditions, hangs in gear. Disable 3rd gear. Will turn on wrench lamp.	Forward (1,2,3,4) clutch, or direct (3,5,R) clutch failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0734	-	Transaxle	Gear 4 incorrect ratio	Forward clutch or overdrive clutch failed to apply. SSA and/or SSD stuck off non-electrical fault (no pressure). Forward clutch and/or overdrive clutch regulator valve stuck in default position. Forward clutch and/or overdrive clutch boost valve stuck in default position.	Customer might notice flares or neutral conditions, hangs in gear. Disable 4th gear. Will turn on wrench lamp.	Forward (1,2,3,4) clutch, or overdrive (4,5,6) clutch failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0735	-	Transaxle	Gear 5 incorrect ratio	Direct clutch or overdrive clutch failed to apply. SSB and/or SSD stuck off non-electrical fault (no pressure). Direct clutch, low/reverse clutch and/or overdrive regulator valve stuck in default position. Low/reverse clutch and/or overdrive clutch boost valve stuck in default position.	Customer might notice flares or neutral conditions, hangs in gear. Disable 5th gear. Will turn on wrench lamp.	Direct (3,5,R) clutch, or overdrive (4,5,6) clutch failed to apply. REFER to the CLUTCH APPLICATION CHART located in Specifications in this service information. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0740	P0743	TCC	TCC solenoid circuit open	Open circuit.	TCC failed off. Will turn on MIL. TCIL flashing	GO to PINPOINT TEST A .
P0741	P0748	TCC	TCC solenoid circuit performance/stuck off.	TCC mechanically stuck off.	Non-electrical TCC solenoid stuck off. TCC mechanical failure. TCC regulator apply valve stuck in release position. TCC control valve stuck in release position. TCC failed to apply (less than 80 rpm slip error lasting at least 3 seconds when TCC is commanded on) 3 consecutive times. Will turn on MIL. TCIL flashing	DTC P0741 is a non-electrical DTC. CLEAR the DTCs. TEST the system for normal operation. If the DTC returns, REFER to TORQUE CONVERTER OPERATION CONCERNS: NO APPLY in Diagnosis By Symptom in this service information.
P0742	P0743	TCC	TCC solenoid circuit stuck on.	Circuit shorted to ground, TCC failed on.	Failure Mode Effect Management action opens the transaxle solenoid power control, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open). Harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL. TCIL flashing	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0743	P0740, P0742 or P0744	TCC	TCC solenoid circuit electrical.	Sister code to P0740, P0742 or P0744 used to illuminate the wrench light.	Will turn on wrench lamp. TCIL flashing	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0744	P0743	TCC	TCC solenoid circuit intermittent.	Circuit short to power.	TCC failed off. Will turn on MIL. TCIL flashing	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0748	P0960, P0962 and P0963	Pressure Control Solenoid A (PCA)	PCA electrical.	PCA circuit failure non-MIL. Sister code to P0960, P0962 and P0963 used to illuminate the wrench light. Additional common fault DTCs, P0750, P0751, P0752.	Failure Mode Effect Management action, see DTCs P0960, P0962 and P0963. Will turn on wrench lamp. TCIL flashing	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0750	P0751	Shift Solenoid A (SSA)	SSA	Open circuit.	Customer might notice a neutral condition, or a single erratic or unexpected shift. 5th and 6th gears only. Poor launch due to 5th gear drive away. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0751	P2700	Forward clutch	SSA performance/ stuck off.	Forward (1,2,3,4) clutch failed to apply when commanded. SSA non-electrical failed stuck off (no pressure). Forward clutch stuck off due to mechanical failure. Forward clutch regulator valve stuck in the default position. Forward clutch boost valve stuck in the default position.	Customer may notice neutral conditions or flares on downshifts from 5th or 6th gear. Once the DTC is stored, gears 1 through 4 are disabled - leaving 5th and 6th gears as the only forward gears. Erratic shifting, harsh engagements, neutral conditions, flares, poor launch performance, harsh reverse engagements. Will turn on MIL.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0752	-	SSA	SSA stuck on.	Forward (1,2,3,4) clutch failed to release when commanded. SSA non-electrical failed stuck on (pressure). Forward clutch stuck on due to mechanical failure. Forward clutch regulator valve stuck in the spring compressed position.	Customer may notice a vehicle deceleration on a shift into 5th or 6th gear (forward clutch failing to release will cause a tie-up in 5th or 6th gear). Customer might notice erratic shifting or being stuck in 4th gear. Once the DTC is stored, 5th and 6th gears are disabled. Will turn on MIL.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0753	P0750, P0973 and P0974	SSA	SSA electrical.	Sister code to P0750, P0973 and P0974 used to illuminate the wrench light. Additional common fault DTCs, P0752, P0754, P0755.	Failure Mode Effect Management action, see DTCs P0750, P0973 and P0974. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0754	-	SSA	SSA intermittent.	Intermittent SSA circuit faults but not lasting long enough to trip DTC, P0750, P0973 or P0974.	Customer might notice unexpected upshifts, downshifts, flairs or neutral conditions. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0755	P0756	SSB	SSB.	Open circuit or short to power.	Customer might notice unexpected upshift. 3rd and 5th gears available. Harsh engagements. Poor launch performance. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0756	P2701	Direct clutch	SSB performance/ stuck off.	Direct (3,5,R) clutch failed off Non-electrical failures where SSB direct clutch is stuck off (no pressure). Direct clutch regulator valve stuck in default position. Direct clutch mechanical failure.	Customer may notice flares or neutral conditions on shifts into 3rd or 5th gear. PCM will command 3 shifts into 3rd or 5th gear, and if direct clutch is failed off the customer will notice flares or neutral conditions that last one second or so. 3rd and 5th gears are disabled, customer might notice transmission hangs in 2nd on acceleration until customer tips out to closed pedal (done to protect overdrive clutch). Will turn on MIL.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0757	P2701	SSB	SSB stuck on.	SSB (direct clutch) failed on, causing direct clutch failed on. Since the hydraulic controls prevent direct clutch and low/reverse clutch on together in the forward ranges we can isolate the solenoid from the clutch. This code sets if: Non-electrical failures where SSB (direct clutch) is stuck on (pressure). Direct clutch regulator valve stuck in spring compress position.	Customer may notice a vehicle deceleration on a shift into 2nd, 4th or 6th gear. Harsh 1-3 shift. Poor launch performance lack of shifts. Will turn on MIL.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0758	P0755, P0976 and P0977	SSB	SSB electrical.	Sister code to P0755, P0976 and P0977 used to illuminate the wrench light. Additional common fault DTCs, P0755, P0976, P0977.	Failure Mode Effect Management action see P0755, P0976 and P0977. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0759	-	SSB	SSB intermittent.	Intermittent SSB circuit faults but not lasting long enough to trip DTC, P0755, P0758, P0976 or P0977.	Customer might notice unexpected upshifts, downshifts, flairs or neutral conditions. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0760	P0761	SSC	SSC.	Open circuit.	Customer might notice erratic, delayed or harsh shifts. Disable 2nd and 6th gears. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0761	P2702	Intermediate clutch	SSC performance/ stuck off.	Intermediate clutch failed off Non-electrical failures where SSC intermediate clutch is stuck off (no pressure). Intermediate clutch stuck off due to mechanical failure. Intermediate clutch regulator valve stuck in the default position.	Customer may notice neutral conditions or flares on shifts to 2nd or 6th gear. Disabled 2nd and 6th gears. Erratic shifting, neutral conditions, flares, higher engine speeds on highway due to 6th gear being disabled. Will turn on MIL.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0762	P0763	SSC	SSC stuck on.	Intermediate clutch failed on, could be due to: Intermediate clutch SSC non-electrical failed stuck on (pressure). Intermediate clutch stuck on due to mechanical failure. Intermediate clutch regulator valve stuck in the spring compressed position.	Customer may notice a vehicle deceleration on a shift into 3rd or 5th gear (intermediate clutch failing to release will cause a tie-up in 3rd or 5th gear). Erratic shifting or being stuck in 6th gear. 3rd, 4th and 5th gears are disabled. Hangs in 2nd gear on acceleration since 2nd-6th upshifts only occur at closed pedal (due to energy limitations of overdrive clutch), harsh reverse engagements (since low/reverse clutch is not on in 2nd gear). Will turn on MIL.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0763	P0760, P0979 and P0980	SSC	SSC electrical.	Sister code to P0760, P0979 and P0980 used to illuminate the wrench light. Additional common fault DTCs, P0755, P0976, P0977.	Failure Mode Effect Management action see P0760, P0979 and P0980. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0764	-	SSC	SSC intermittent.	Intermittent SSC circuit faults but not lasting long enough to trip DTC, P0760, P0979 and P0980.	Customer might notice unexpected upshifts, downshifts, flairs or neutral conditions. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0765	P0766	SSD	SSD.	Open circuit.	Overdrive clutch failed on, only 4th, 5th and 6th gears available. Harsh engagements. Poor launch due to 4th gear drive away. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0766	P2704	Overdrive clutch system fault includes non-electrical SSD fault, main control valve body and clutch	SSD performance stuck off.	Overdrive clutch failed off. Non-electrical failure where SSD, low/ reverse and overdrive clutch is stuck off (no pressure). Low/reverse clutch/ overdrive clutch regulator valve stuck in default position. Low/reverse clutch/ overdrive clutch boost valve stuck in default position.	Customer may notice flares or neutral conditions on shifts into 4th, 5th or 6th gear. Erratic shifting, flares, neutral conditions while the code is being set. 1st, 4th, 5th and 6th gears are disabled - may notice high engine rpm since 3rd is highest available gear. May get delayed or no reverse engagement (need low/reverse clutch on to achieve reverse). Will turn on MIL.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0767	P07A9, P2704	Overdrive or low/reverse clutch	SSD stuck on.	Overdrive clutch failed on, could be due to: Low/reverse or overdrive clutch SSD non-electrical failed stuck on (pressure). Overdrive clutch stuck on due to mechanical failure. Low/reverse, overdrive clutch regulator valve stuck in the spring-compressed position.	Customer may notice vehicle deceleration on shifts into 2nd or 3rd gear (overdrive clutch failing to release will cause a tie-up in 2nd or 3rd gear). 1st, 2nd and 3rd gears are disabled. Poor launch due to 4th gear drive away. Harsh engagements. Will turn on MIL.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0768	P0765, P0982 and P0983	SSD	SSD electrical	Sister code to P0765, P0982 and P0983 used to illuminate the wrench light. Additional common fault DTCs, P0767, P0769, P0770.	Failure Mode Effect Management action see P0765, P0982 and P0983. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0769	-	SSD	SSD intermittent.	Intermittent SSD circuit faults but not lasting long enough to trip DTC, P0765, P0768, P0982 and P0983.	Customer might notice unexpected upshifts, downshifts, flairs or neutral conditions. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0770	P0773	Shift Solenoid E (SSE)	SSE.	Open, short to ground or short to power.	SSE failed off (no pressure): Customer might notice 4th gear drive away when 1st gear is commanded. Failed off (no pressure) then 1st gear with engine braking is disabled. May or may not notice 2nd gear provided when 1st gear selected in low manual range. Harsh reverse engagements since low/reverse clutch does not apply in neutral or drive in this failure mode. SSE failed on (pressure): High side is turned off. Poor launch performance due to 5th gear drive away. Harsh engagements. No TCC apply. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0771	P0984	SSE failed off	SSE performance/stuck off.	SSE controls the multiplexing of SSD low/ reverse and overdrive clutch. If solenoid fails off (no pressure) then 1st gear is failed to 4th gear. If clutch select valve 2 sticks in the default position then 1st gear with engine braking is failed to 4th gear and reverse is failed to neutral. The diagnostic does not distinguish SSE stuck off from valve 2 stuck in default. This code means either: SSE short to power, failed off (no pressure). Valve 2 stuck in default position.	If SSE is failed on or valve 2 is stuck in default position, then the customer will get 4th gear when 1st gears is selected Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0772	P0984	SSE failed on	SSE stuck on.	SSE controls the multiplexing of SSD low/ reverse and overdrive clutch. If the solenoid fails on (pressure) then, 1st and 2nd gear are the only available gears. 3rd gear is failed to 1st gear, 4th gear is failed to 1st gear, 5th gear is failed to neutral, and 6th gear is a tie-up. If clutch select valve 2 sticks in the spring-compressed position, the same ratio pattern will occur. This code means either: SSE short to ground, failed on (pressure). Valve 2 stuck in spring compressed position.	If SSE is failed on or valve 2 is stuck in spring compressed position, then 1st and 2nd gears are the only available gears. Customer might notice flares on shifts into 3rd gear. Deceleration on shifts into 4th gear since you get 1st gear or a neutral condition on shifts into 5th gear. High engine rpm since 2nd gear is top available gear. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0773	P0770	SSE	SSE electrical.	Open, short to ground or short to power in solenoid or wiring.	Sister code to P0770 used to illuminate the wrench light. Failure Mode Effect Management action see P0770. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0774	-	SSE	SSE intermittent.	Intermittent SSD circuit faults but not lasting long enough to trip DTC, P0770.	Failure Mode Effect Management action see P0770. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P07A5	-	Direct clutch	Transmission direct clutch stuck on.	Ratio based test. The clutch control bypass valve (multiplex valve) exhausts the direct clutch when the valve is in the compressed position, where SSD points in the low/reverse position, the diagnostic can isolate the direct clutch stuck on from SSB stuck on because getting 3rd gear in 1st when the clutch control bypass valve is in the spring compressed position indicates that SSB cannot be the cause.	Customer may notice slow acceleration from stop. May be in 3rd gear when 1st gear is commanded. Once the DTC is stored, 3rd and 5th gears are only available. Erratic shifting, harsh engagements, poor launch performance. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P07A8	-	Low/reverse clutch	Transmission low/reverse clutch performance/stuck off.	SSD is multiplexed through the clutch control bypass valve (multiplex valve) to the low/reverse and overdrive clutch, the diagnostic can isolate the low/reverse clutch failed off from SSD stuck off when the overdrive clutch applies normally and the low/reverse clutch did not.	Customer may notice no reverse. Disable 1st gear. Delayed engagement into drive. Poor launch performance due to 2nd gear launch. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P07A9	P0767	Low/reverse clutch	Transmission low/reverse clutch stuck on.	SSD is multiplexed through the clutch control bypass valve (multiplex valve) to the low/reverse and overdrive clutch, the diagnostic can isolate the low/reverse stuck on by turning off SSE. If the transaxle shifts into 4th when the clutch control bypass valve moves SSD is stuck on, but if the transaxle stays in 1st then the low/ reverse is stuck on.	Low/reverse clutch failed on. One-Way Clutch (OWC) transmits torque in both directions. Stuck in 1st gear. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P07AA	-	Overdrive clutch	Transmission overdrive clutch performance/stuck off.	SSD is multiplexed through the clutch control bypass valve (multiplex valve) between the low/ reverse and overdrive clutch, the diagnostic can isolate the overdrive clutch failed off from SSD stuck off when the low/reverse clutch applies normally but the overdrive clutch is stuck off.	Overdrive clutch failed off. Disable 4th, 5th and 6th gears. Reverse may be delayed or disabled. High engine rpm. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0815	-	Upshift switch circuit	SelectSwtch ™ upshift switch output circuit failure	The associated circuitry to and from the SelectSwtch™ switch, fuse or the SelectSwtch™ switch itself may have an open or is shorted to ground.	SelectSwtch™ upshift inoperative. Will turn on wrench lamp.	REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS - AISIN AW21/6F35 -- FUSION, MILAN & MKZ (EXCEPT HYBRID) article.
P0816	-	Downshift switch circuit	SelectSwtch ™ downshift switch output circuit failure	The associated circuitry to and from the SelectSwtch™ switch, fuse or the SelectSwtch™ switch itself may have an open or is shorted to ground.	SelectSwtch™ downshift inoperative. Will turn on wrench lamp.	REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS - AISIN AW21/6F35 -- FUSION, MILAN & MKZ (EXCEPT HYBRID) article.
P0867	-	Transmission hydraulic and clutch systems	Transmission fluid pressure.	The control valve test raises line pressure to insure that the clutch control bypass valve (multiplex valve) is latched, then turns on SSE to test for a stuck TCC control valve under steady state operation in 4th, 5th and 6th gear. If the ratio breaks away the test is aborted. If enough ratio break away occur, the DTC is set.	Multiplex latch pressure inadequate (valve moves when SSE turns on). Overdrive clutch pressure issue. Line pressure issues. Solenoid regulator valve issues. Customer may notice flairs during test. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P0960	P0748	PCA	PCA control circuit/open.	PCA circuit has failed to 0 current.	Failed to maximum line pressure. Harsh engagements. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0961	P0748	PCA	PCA control circuit range/ performance.	Intermittent PCA short to ground. Fault present long enough to notice a neutral condition (minimum pressure) but not present long enough to store a DTC.	Harsh engagement and harsh shifts. Will turn on wrench lamp.	GO to PINPOINT TEST A .
P0962	P0748	PCA	PCA control circuit low.	PCA short to ground circuit failure.	Failed to 0 current, minimum line pressure: Failure Mode Effect Management action opens the transaxle solenoid power control relay, removing power from all solenoids which provides maximum line pressure. Harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0963	P0748	PCA	PCA control circuit high.	PCA short to power circuit fault.	Failed to 0 current, maximum line pressure: Harsh engagements. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0973	P0753	SSA	SSA control circuit low.	Short to ground.	Failure Mode Effect Management action opens the transaxle solenoid power control relay, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open). Harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0974	P0753	SSA	SSA control circuit high.	Short to power.	Forward clutch is failed off - 5th and 6th gears only available forward gears. Neutral condition or flare when fault occurs. Poor launch due to 5th gear drive away Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0976	P0758	SSB	SSB control circuit low.	Short to ground.	Failure Mode Effect Management action opens the transaxle solenoid power control relay, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open). Harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0977	P0758	SSB	SSB control circuit high.	Short to power.	Direct clutch failed on - only 3rd and 5th gears available. Harsh 1-3 shift if failure occurs while in 1st. Poor launch due to 3rd gear drive away. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0979	P0763	SSC	SSC control circuit low.	Short to ground.	Failure Mode Effect Management action opens the transaxle solenoid power control relay, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th gear as the only forward gear with TCC open). Harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0980	P0763	SSC	SSC control circuit high.	Open circuit.	If fault occurs while in 2nd or 6th gear, customer might notice a neutral condition before diagnostics disables 2nd and 6th gears. Erratic, delayed or harsh shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0982	P0768	SSD	SSD control circuit low.	Short to ground.	Failure Mode Effect Management action opens the transaxle solenoid power control relay, removing power from all solenoids (get PARK, REVERSE, NEUTRAL and 5th as the only forward gear with TCC open), harsh engagements. Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0983	P0768	SSD	SSD control circuit high.	Open circuit.	Only 4th, 5th and 6th gears available. Harsh engagements. Poor launch due to 4th gear drive away. Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P0984	P0771, P0772	SSE	SSE control circuit range/performance.	This DTC sets with either P0771 or P0772.	Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P1500	P0722	VSS sensor	OSS sensor circuit.	PCM has detected VSS sensor signal failed to 0 speed when vehicle conditions (mainly turbine speed) indicate OSS sensor output should be present. Electrical failures (open, short) of the OSS sensor wiring, connector or a failure of the OSS sensor itself will cause this failure.	Failure Mode Effect Management action opens transaxle solenoid power control (removes power from all solenoids). provides PARK, REVERSE, NEUTRAL AND 5th gear with maximum line pressure and open TCC available (controlled by the manual lever). Harsh engagements (due to maximum line pressure). Poor launch performance (due to 5th drive away). Will turn on MIL.	REPAIR the more specific DTC first. GO to PINPOINT TEST C .
P1636	-	PCM	Inductive signature chip communication error.	Lost communication with solenoid driver. The solenoid driver is an internal PCM chip that controls the solenoids. The main microchip communicates with the solenoid driver over a serial interface, sending out the desired solenoid state and receiving back a circuit fault status. If communication is lost with the solenoid driver, the solenoid states become unknown, so the control system forces the transaxle solenoid power control relay off.	Transaxle solenoid power control relay turned off, providing PARK, REVERSE, NEUTRAL and 5th gear with TCC open and maximum line pressure. Harsh engagements. Poor performance launch (due to 5th drive away). No TCC apply. No shifts. Will turn on MIL.	INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS - 2.5L -- FUSION & MILAN (EXCEPT HYBRID) article or ELECTRONIC ENGINE CONTROLS - 3.0L (4V) -- FUSION & MILAN article.
P163E	-	TRID block	Transmission control module programming error.	TRID version incorrect (TRID version does not match version in PCM Calibration). 7-digit service banding code checksum or total TRID block checksum invalid. Solenoid and Clutch characterization data unavailable. Failure Mode Effect Management will increase pressure and allow only PARK, REVERSE, NEUTRAL, 1st and 3rd gear only.	Costumer may notice, high engine rpm. 1st and 3rd gear only. No TCC apply. Will turn on MIL.	REFER to SOLENOID BODY STRATEGY in this service information.
P163F	-	TRID block	TRID ID block corrupted, not programmed.	TRID data not programmed. Solenoid and Clutch strategy data unavailable. Failure Mode Effect Management will increase pressure and allow only PARK, REVERSE, NEUTRAL, 1st and 3rd only.	Failure Mode Effect Management action of limits function to 1st and 3rd gear. High engine rpm, lack of shifts complaints. No TCC apply. Will turn on MIL.	REFER to SOLENOID BODY STRATEGY in this service information.
P1702	P0706, P0707 and P0708	TR sensor	TR sensor circuit intermittent.	Sister code to P0706 P0707 and P0708 used to illuminate the wrench light.	Possible no crank, only PARK, REVERSE, NEUTRAL and 5th gear available, harsh engagements. Extremely delayed engagements (until a DTC is set). After a DTC is set and the high side opened - harsh engagements, poor performance (due to a 5th gear drive away), no shifts. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST D .
P1705	-	TR sensor	TR circuit not indicating park/neutral during self-test.	TR sensor not indicating Park or Neutral during Key ON Engine OFF (KOEO) or Key ON Engine Running (KOER) self-test.	-	Rerun KOEO or KOER only.
P1711	-	TFT	TFT sensor out of self-test range.	TFT sensor out of self-test range equals less than -1°C (30°F) or greater than 105°C (220°F) during KOEO or KOER self-test.	-	RERUN KOEO or KOER only.
P1744	P0741	TCC	TCC solenoid circuit.	Sister code to P0741 used to illuminate the wrench light. Additional common DTC, P163F.	Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P1780	-	Transmission Control Switch (TCS)	TCS (Overdrive (O/D) Cancel) circuit out of self-test range.	TCS did not change states during KOER self-test.	Customer cannot enter or exit the overdrive feature.	REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS - AISIN AW21/6F35 -- FUSION, MILAN & MKZ (EXCEPT HYBRID) article.
P1783	-	Transmission overtemperature	Transmission over temperature condition.	Transmission over temperature condition (greater than 135°C [275°F] for at least 5 seconds).	Torque converter lockup happens earlier than expected. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P1910	-	Reverse lamp control	Reverse lamp control circuit/open.	Reverse lamp control circuit fault. 6F35 TR sensor does not have a high current reverse lamp control switch. This has moved to the PCM.	Reverse lamps do not function correctly. Will turn on wrench lamp.	REFER to EXTERIOR LIGHTING -- FUSION, MILAN & MKZ article.
P1921	P0706, P0707 and P0708	TR switch	Transmission range signal	The PCM sets this DTC when the ignition switch is turned to the crank position and before the PCM receives an engine run signal.	Engine may not crank.	REPAIR the more specific DTC first. GO to PINPOINT TEST D .
P2700	P0751 and P0752	Forward clutch system fault	Transmission forward clutch apply time range/ performance.	This code sets with either DTC P0751 or P0752.	Will turn on wrench lamp.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2701	P0756 and P0757	Direct clutch system fault	Transmission direct clutch apply time range/performance.	This code sets with either DTC P0756 or P0757.	Will turn on wrench lamp.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2702	P0761 and P0762	Intermediate clutch system faults	Transmission intermediate clutch apply time range/ performance.	This code sets with either DTC P0761 or P0762.	Will turn on wrench lamp.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2703	P0766 and P2704	Low/Reverse clutch and OWC faults (covers just the clutches)	Transmission low/reverse clutch apply time range/ performance.	Low/reverse clutch stuck off with overdrive clutch stuck off. Most likely cause is SSD non-electrical failure or low/reverse/ overdrive regulator valve stuck in default position.	Low/reverse clutch off is a ratio based test. Low/reverse clutch is only tested for failed off in the low manual lever position. The customer might notice no engine braking in 1st gear, and erratic shifting as the diagnostics isolates the fault to low/reverse clutch failed off. Delayed or no reverse engagement. Will turn on wrench lamp.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2704	P0766, P0767 and P2703	Overdrive clutch system faults	Transmission overdrive clutch apply time range/ performance.	Overdrive clutch stuck off with low/ reverse clutch stuck off. Most likely cause is SSD non-electrical failure or low/ reverse/overdrive regulator valve stuck in default position. Overdrive clutch stuck on. Possibly overdrive clutch, SSD, low/reverse/ overdrive regulator valve stuck in spring compressed position.	Overdrive clutch failed off. Will turn on wrench lamp.	REPAIR the more specific DTC first. REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2705	-	OWC failed	Transmission OWC apply time range/performance.	The OWC holds in 1st gear. If the OWC fails off, 1st gear is failed to neutral. 1st gear is disabled for this failure since low/reverse clutch is not intended to hold power on torque in 1st gear.	Customer might notice neutral conditions when 1st gear is commanded. Erratic shifting as the diagnostic isolates the cause of the neutral condition to the OWC being failed. Poor launch performance (due to 2nd gear drive away). Harsh engagements. Will turn on wrench lamp.	REFER to DIAGNOSIS BY SYMPTOM in this service information.
P2760	P0743 and P0744	TCC solenoid	TCC pressure control solenoid intermittent.	Intermittent TCC solenoid short to ground. A short to ground will cause the TCC to apply, which can stall the engine at low vehicle speeds. The PCM will disable the high side driver until vehicle speed is high enough that the engine won't stall. With the high side driver off the fault can not be detected. If the fault goes away while the high side is off the vehicle will have a 5th gear launch with no DTC. If this occurs 3 times with no DTC P0742 being set, then DTC P2760 will set.	Poor launch performance (due to 5th gear drive away). No TCC apply. No shifts. Will turn on wrench lamp.	REPAIR the more specific DTC first. GO to PINPOINT TEST A .
P2783	-	Torque converter	Torque converter temperature too high.	TCC control valve stuck in the apply position. When the TCC is commanded open there will be no flow through the TCC (both apply and release circuits will be exhausted). Test will run in 3rd gear or higher when valve 2 is in the latched position, pointing SSD at overdrive clutch when the TCC is commanded open. SSE is turned on, if the control valve is stuck, this will cause the TCC to apply even though the TCC solenoid is off.	Torque converter temperature too high. Erratic shifts, vehicle disengages at a stop while in drive or low, early TCC apply. Will turn on MIL.	REFER to DIAGNOSIS BY SYMPTOM in this service information.