| B1087:83 |
LIN Bus "A": Value of Signal Protection Calculation Incorrect |
GO to PINPOINT TEST W |
| B1087:86 |
LIN Bus "A": Signal Invalid |
GO to PINPOINT TEST W |
| B1087:88 |
LIN Bus "A": Bus Off |
GO to PINPOINT TEST W |
| B1109:11 |
Passenger Door Central Locking Motor: Circuit Short To Ground |
GO to PINPOINT TEST J |
| B1109:15 |
Passenger Door Central Locking Motor: Circuit Short To Battery or Open |
GO to PINPOINT TEST J |
| B110B:01 |
Rear Door Passenger Side Central Locking Motor: General Electrical Failure |
GO to PINPOINT TEST J |
| B1288:02 |
Rear Lock Motor Common Circuit: General Signal Failure |
GO to PINPOINT TEST J |
| B12AB:11 |
Front Window Position Sensor Power Supply: Circuit Short To Ground |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12B6:11 |
Front Lock Motor Common Circuit: Circuit Short To Ground |
GO to PINPOINT TEST J |
| B12B6:15 |
Front Lock Motor Common Circuit: Circuit Short To Battery or Open |
GO to PINPOINT TEST J |
| B12C2:11 |
Puddle Lamp: Circuit Short To Ground |
REFER to: INTERIOR LIGHTING
(417-02 Interior Lighting, Diagnosis and Testing). |
| B12C2:15 |
Puddle Lamp: Circuit Short To Battery or Open |
REFER to: INTERIOR LIGHTING
(417-02 Interior Lighting, Diagnosis and Testing). |
| B12C3:11 |
Rear Window Position Sensor Power Supply: Circuit Short To Ground |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12C4:11 |
Mirror Turn Indicator: Circuit Short To Ground |
REFER to: TURN SIGNAL AND HAZARD LAMPS
(417-01 Exterior Lighting, Diagnosis and Testing). |
| B12C4:15 |
Mirror Turn Indicator: Circuit Short To Battery or Open |
REFER to: TURN SIGNAL AND HAZARD LAMPS
(417-01 Exterior Lighting, Diagnosis and Testing). |
| B12C5:02 |
Front Window Lifter Motor Up Relay: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12C6:02 |
Rear Window Lifter Motor Up Relay: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12C7:02 |
Rear Window Lifter Motor Down Relay: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12C8:02 |
Front Window Lifter Motor Down Relay: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12D8:11 |
Mirror Heater Output: Circuit Short To Ground |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B12D8:15 |
Mirror Heater Output: Circuit Short To Battery or Open |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B12DC:02 |
Front Window Motion/Position Sensor: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12DC:54 |
Front Window Motion/Position Sensor: Missing Calibration |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12DD:02 |
Rear Window Motion/Position Sensor: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12DD:54 |
Rear Window Motion/Position Sensor: Missing Calibration |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12DE:01 |
Front Window Local Up Switch: General Electrical Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12DF:01 |
Front Window Local Down Switch: General Electrical Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12E9:02 |
Rear Window Local Up/Down Switch: General Signal Failure |
REFER to: GLASS, FRAMES AND MECHANISMS
(501-11 Glass, Frames and Mechanisms, Diagnosis and Testing). |
| B12FF:11 |
Rear Door Switch Illumination: Circuit Short To Ground |
REFER to: INSTRUMENT PANEL CLUSTER (IPC) AND PANEL ILLUMINATION
(413-00 Instrument Panel Cluster (IPC) and Panel Illumination, Diagnosis and Testing). |
| B12FF:15 |
Rear Door Switch Illumination: Circuit Short To Battery or Open |
REFER to: INSTRUMENT PANEL CLUSTER (IPC) AND PANEL ILLUMINATION
(413-00 Instrument Panel Cluster (IPC) and Panel Illumination, Diagnosis and Testing). |
| B1302:11 |
Mirror Motor Common: Circuit Short To Ground |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B1302:15 |
Mirror Motor Common: Circuit Short To Battery or Open |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B1C11:11 |
Passenger Left/Right Mirror Motor: Circuit Short To Ground |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B1C11:15 |
Passenger Left/Right Mirror Motor: Circuit Short To Battery or Open |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B1C12:11 |
Passenger Up/Down Mirror Motor: Circuit Short To Ground |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| B1C12:15 |
Passenger Up/Down Mirror Motor: Circuit Short To Battery or Open |
REFER to: REAR VIEW MIRRORS
(501-09 Rear View Mirrors, Diagnosis and Testing). |
| U0010:88 |
Medium Speed CAN Communication Bus: Bus Off |
The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). VERIFY the integrity of the connectors and wiring. Refer to SYSTEM WIRING DIAGRAMS
Wiring Diagrams Cell 14 for schematic and connector information. |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to PINPOINT TEST X |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to PINPOINT TEST Y |
| U0199:00 |
Lost Communication With "Door Control Module A": No Sub Type Information |
GO to PINPOINT TEST Z |
| U0202:87 |
Lost Communication With "Door Control Module D": Missing Message |
GO to PINPOINT TEST AB |
| U0300:00 |
Internal Control Module Software Incompatibility: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC
is retrieved again, INSTALL a new PDM
. REFER to: DOOR MODULE
(419-10 Multifunction Electronic Modules, Removal and Installation). |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) set in the ECM
. REFER to: ELECTRONIC ENGINE CONTROLS - PLUG-IN HYBRID ELECTRIC VEHICLE (PHEV)
(303-14 Electronic Engine Controls - 2.0L Duratec - Hybrid (96kW/130PS), Diagnosis and Testing). |
| U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) set in the TCM
. REFER to: AUTOMATIC TRANSMISSION - HYBRID ELECTRIC VEHICLE (HEV)
(307-01 Automatic Transmission - Vehicles With: Automatic Transmission - HF35, Diagnosis and Testing). |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) set in the BCM
. REFER to: BODY CONTROL MODULE (BCM)
(419-10 Multifunction Electronic Modules, Diagnosis and Testing). |
| U2010:11 |
Switch Illumination: Circuit Short To Ground |
REFER to: INSTRUMENT PANEL CLUSTER (IPC) AND PANEL ILLUMINATION
(413-00 Instrument Panel Cluster (IPC) and Panel Illumination, Diagnosis and Testing). |
| U2010:15 |
Switch Illumination: Circuit Short To Battery Or Open |
REFER to: INSTRUMENT PANEL CLUSTER (IPC) AND PANEL ILLUMINATION
(413-00 Instrument Panel Cluster (IPC) and Panel Illumination, Diagnosis and Testing). |
| U2014:44 |
Control Module Hardware: Data Memory Failure |
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC
is retrieved again, INSTALL a new PDM
. REFER to: DOOR MODULE
(419-10 Multifunction Electronic Modules, Removal and Installation). |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC
is retrieved again, INSTALL a new PDM
. REFER to: DOOR MODULE
(419-10 Multifunction Electronic Modules, Removal and Installation). |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC
is retrieved again, INSTALL a new PDM
. REFER to: DOOR MODULE
(419-10 Multifunction Electronic Modules, Removal and Installation). |
| U3003:62 |
Battery Voltage: Signal Compare Failure |
GO to PINPOINT TEST AC |