Body Control Module (BCM)
BODY CONTROL MODULE (BCM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1115:11 | High Mounted Stop Lamp Control: Circuit Short To Ground | GO to Pinpoint Test Q . |
| B123A:11 | Left Front Turn Indicator: Circuit Short To Ground | GO to Pinpoint Test U . |
| B123A:15 | Left Front Turn Indicator: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B123B:11 | Right Front Turn Indicator: Circuit Short To Ground | GO to Pinpoint Test U . |
| B123B:15 | Right Front Turn Indicator: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B1247:11 | Left Rear Turn Indicator: Circuit Short To Ground | GO to Pinpoint Test U . |
| B1247:15 | Left Rear Turn Indicator: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B1248:11 | Right Rear Turn Indicator: Circuit Short To Ground | GO to Pinpoint Test U . |
| B1248:15 | Right Rear Turn Indicator: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B1277:11 | Reverse Lamp: Circuit Short To Ground | GO to Pinpoint Test AB . |
| B1277:15 | Reverse Lamp: Circuit Short To Battery or Open | If the reverse lamps are inoperative, GO to Pinpoint Test AB . If the reverse lamps are always on, GO to Pinpoint Test AD . |
| B132B:11 | Left Stop/Turn Lamp: Circuit Short To Ground | GO to Pinpoint Test Q . |
| B132B:15 | Left Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to Pinpoint Test Q . If the stoplamp is always on, GO to Pinpoint Test R . |
| B132C:11 | Right Stop/Turn Lamp: Circuit Short To Ground | GO to Pinpoint Test Q . |
| B132C:15 | Right Stop/Turn Lamp: Circuit Short To Battery or Open | If the stoplamp is inoperative, GO to Pinpoint Test Q . If the stoplamp is always on, GO to Pinpoint Test R . |
| B1A85:11 | Ambient Light Sensor: Circuit Short To Ground | GO to Pinpoint Test O . |
| B1A85:13 | Ambient Light Sensor: Circuit Open | GO to Pinpoint Test O . |
| B1C98:11 | Left Corner Lamp Circuit: Circuit Short To Ground | GO to Pinpoint Test U . |
| B1C98:15 | Left Corner Lamp Circuit: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B1C99:11 | Right Corner Lamp Circuit: Circuit Short To Ground | GO to Pinpoint Test U . |
| B1C99:15 | Right Corner Lamp Circuit: Circuit Short To Battery or Open | GO to Pinpoint Test U . |
| B1D00:11 | Left Low Beam: Circuit Short To Ground | GO to Pinpoint Test A . |
| B1D00:15 | Left Low Beam: Circuit Short To Battery or Open | If the headlamp is inoperative, GO to Pinpoint Test A . If the headlamp is always on, GO to Pinpoint Test C . |
| B1D01:11 | Right Low Beam: Circuit Short To Ground | GO to Pinpoint Test A . |
| B1D01:15 | Right Low Beam: Circuit Short To Battery or Open | If the headlamp is inoperative, GO to Pinpoint Test A . If the headlamp is always on, GO to Pinpoint Test C . |
| B1D02:11 | Left High Beam Circuit: Circuit Short To Ground | GO to Pinpoint Test B . |
| B1D02:15 | Left High Beam Circuit: Circuit Short To Battery or Open | If the headlamp is inoperative, GO to Pinpoint Test B . If the headlamp is always on, GO to Pinpoint Test D . |
| B1D03:11 | Right High Beam Circuit: Circuit Short To Ground | GO to Pinpoint Test B . |
| B1D03:15 | Right High Beam Circuit: Circuit Short To Battery or Open | If the headlamp is inoperative, GO to Pinpoint Test B . If the headlamp is always on, GO to Pinpoint Test D . |
| B1D35:11 | Hazard Switch: Circuit Short To Ground | GO to Pinpoint Test V . |
| C0040:12 | Brake Pedal Switch "A": Circuit Short To Battery | GO to Pinpoint Test R . |
| U1000:00 | Solid State Driver Protection Activated - Driver Disabled: No Sub Type Information | The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The Body Control Module (BCM) cannot enable the output until the cause of the short is corrected. ADDRESS all other DTCs first . After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the self-test. |
| U3000:49 | Control Module: Internal Electronic Failure | The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other DTCs first . After the cause of the concern is corrected, INSTALL a new BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES . TEST the system for normal operation. |