| B00A0:54 |
Occupant Classification System: Missing Calibration |
GO to PINPOINT TEST Z
. |
| B00A0:67 |
Occupant Classification System: Signal Incorrect After Event |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| B00A0:76 |
Occupant Classification System: Wrong Mounting Position |
GO to PINPOINT TEST Z
. |
| B00A0:97 |
Occupant Classification System: Component or System Operation Obstructed or Blocked |
GO to PINPOINT TEST P
. |
| B00C0:12 |
Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery |
GO to PINPOINT TEST R
. |
| B00C0:13 |
Passenger Seat Occupant Classification Sensor "A": Circuit Open |
GO to PINPOINT TEST R
. |
| B00C0:1A |
Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold |
GO to PINPOINT TEST R
. |
| B00C0:49 |
Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure |
GO to PINPOINT TEST Z
. |
| B00C0:81 |
Passenger Seat Occupant Classification Sensor "A": Invalid Serial Data Received |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| B00C1:12 |
Passenger Seat Occupant Classification Sensor "B": Circuit Short To Battery |
GO to PINPOINT TEST S
. |
| B00C1:13 |
Passenger Seat Occupant Classification Sensor "B": Circuit Open |
GO to PINPOINT TEST S
. |
| B00C1:1A |
Passenger Seat Occupant Classification Sensor "B": Circuit Resistance Below Threshold |
GO to PINPOINT TEST S
. |
| B00C1:49 |
Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure |
GO to PINPOINT TEST Z
. |
| B00C1:81 |
Passenger Seat Occupant Classification Sensor "B": Invalid Serial Data Received |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| B00C2:12 |
Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery |
GO to PINPOINT TEST T
. |
| B00C2:13 |
Passenger Seat Occupant Classification Sensor "C": Circuit Open |
GO to PINPOINT TEST T
. |
| B00C2:1A |
Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Below Threshold |
GO to PINPOINT TEST T
. |
| B00C2:49 |
Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure |
GO to PINPOINT TEST Z
. |
| B00C2:81 |
Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data Received |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| B00C3:12 |
Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery |
GO to PINPOINT TEST U
. |
| B00C3:13 |
Passenger Seat Occupant Classification Sensor "D": Circuit Open |
GO to PINPOINT TEST U
. |
| B00C3:1A |
Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Below Threshold |
GO to PINPOINT TEST U
. |
| B00C3:49 |
Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure |
GO to PINPOINT TEST Z
. |
| B00C3:81 |
Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data Received |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| B1193:00 |
Crash Event Storage Full and Locked: No Sub Type Information |
INSTALL a new passenger seat track assembly with weight sensor bolts. REFER to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT
. |
| B1A59:01 |
Sensor 5 Volt Supply: General Electrical Failure |
GO to PINPOINT TEST AA
. |
| B1A59:11 |
Sensor 5 Volt Supply: Circuit Short to Ground |
GO to PINPOINT TEST AA
. |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
U0100:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new Occupant Classification System Module (OCSM) as part of repair for DTC U0100:00. REFER to MODULE COMMUNICATIONS NETWORK
to diagnose lost communication with the PCM. |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
U0151:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0151:00. REFER to MODULE COMMUNICATIONS NETWORK
to diagnose lost communication with the Restraints Control Module (RCM). |
| U0401:00 |
Invalid Data Received From ECM/PCM "A": No Sub Type Information |
U0401:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT PCM Self Test. REPAIR any speed-related DTCs. REFER to DIAGNOSTIC TROUBLE CODE (DTC) CHARTS AND DESCRIPTIONS
in Powertrain Control/Emissions Diagnosis (PC/ED) article. |
| U200D:12 |
Control Module Output Power A: Circuit Short To Battery |
GO to PINPOINT TEST AC
. |
| U3000:49 |
Control Module: Internal Electronic Failure |
INSTALL a new Occupant Classification System Module (OCSM). REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - MANUAL SEAT TRACK
or OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - POWER SEAT TRACK
. |
| U3000:53 |
Control Module: Deactivated |
INSTALL a new Occupant Classification System Module (OCSM). REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - MANUAL SEAT TRACK
or OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - POWER SEAT TRACK
. |
| U3000:54 |
Control Module: Missing Calibration |
CARRY OUT the OCS Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET
. |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to PINPOINT TEST AD
. |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to PINPOINT TEST AD
. |