Automatic Transaxle/Transmission DTCS: 6F35
DTC CHART
| DTC | Description | Action |
|---|---|---|
| P0657 | Actuator Supply Voltage A Circuit Open | Power to all solenoids has been interrupted, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST F . |
| P0701 | Transmission Control System Range/Performance | DTCs P2700, P2701, P2702, P2703 and/or P2704 may set. CLEAR the DTCs. If the DTC returns, GO to SYMPTOM CHART . |
| P0702 | Transmission Control System Electrical | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If the DTC returns, REFER to CHARGING SYSTEM . |
| P0706 | TR Sensor A Circuit Range/Performance | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J . |
| P0707 | TR Sensor A Circuit Low | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J . |
| P0708 | TR Sensor A Circuit High | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J . |
| P0710 | TFT Sensor A Circuit | DTCs P0712 or P0713 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G . REPAIR the more specific DTC first. |
| P0711 | TFT Sensor A Circuit Range/Performance | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G . REPAIR the more specific DTC first. |
| P0712 | TFT Sensor A Circuit Low | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G . REPAIR the more specific DTC first. |
| P0713 | TFT Sensor A Circuit High | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G . REPAIR the more specific DTC first. |
| P0715 | Turbine/Input Shaft Speed Sensor A Circuit | DTC P0717 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K . REPAIR the more specific DTC first. |
| P0717 | Turbine/Input Shaft Speed Sensor A Circuit No Signal | DTC P0715 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K . REPAIR the more specific DTC first. |
| P0718 | Turbine/Input Shaft Speed Sensor A Circuit Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K . |
| P0720 | OSS Sensor Circuit | DTC P0722 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L . REPAIR the more specific DTC first. |
| P0721 | OSS Sensor Circuit Range/Performance | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L . |
| P0722 | OSS Sensor Circuit No Signal | DTC P0720 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L . REPAIR the more specific DTC first. |
| P0729 | Gear 6 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 5-6 shift/harsh/soft/slipping. |
| P0731 | Gear 1 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0732 | Gear 2 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART . |
| P0733 | Gear 3 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0734 | Gear 4 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0735 | Gear 5 Incorrect Ratio | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 4-5 shift/harsh/soft/slipping. |
| P0740 | TCC Clutch Solenoid Circuit/Open | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H . |
| P0741 | TCC Solenoid Circuit Performance/Stuck Off | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART . |
| P0742 | TCC Solenoid Circuit Stuck On | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H . |
| P0743 | TCC Solenoid Circuit Electrical | DTCs P0740, P0742 and/or P0744 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H . REPAIR the more specific DTC first. |
| P0744 | TCC Solenoid Circuit Intermittent | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H . REPAIR the more specific DTC first. |
| P0748 | LPC A Electrical | DTCs P0960, P0962 and/or P0963 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I . REPAIR the more specific DTC first. |
| P0750 | SSA | DTC P0751 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A . REPAIR the more specific DTC first. |
| P0751 | SSA Performance/Stuck Off | DTC P2700 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns/no forward. |
| P0752 | SSA Stuck On | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/only gears 1, 2, 3, 4 available. |
| P0753 | SSA Electrical | DTCs P0750, P0973 and/or P0974 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A . REPAIR the more specific DTC first. |
| P0754 | SSA Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A . |
| P0755 | SSB | DTC P0756 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B . REPAIR the more specific DTC first. |
| P0756 | SSB Performance/Stuck Off | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/only gears 3 and 5 available. |
| P0757 | SSB Stuck On | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0758 | SSB Electrical | DTCs P0755, P0976 and/or P0977 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B . REPAIR the more specific DTC first. |
| P0759 | SSB Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B . |
| P0760 | SSC | DTC P0761 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C . REPAIR the more specific DTC first. |
| P0761 | SSC Performance/Stuck Off | DTC P2702 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0762 | SSC Stuck On | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/only gears 2 and 6 available. |
| P0763 | SSC Electrical | DTCs P0760, P0979 and/or P0980 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C . REPAIR the more specific DTC first. |
| P0764 | SSC Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C . |
| P0765 | SSD | DTC P0766 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D . REPAIR the more specific DTC first. |
| P0766 | SSD Performance/Stuck Off | DTC P2704 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P0767 | SSD Stuck On | DTCs P07A9 and/or P2704 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0768 | SSD Electrical | DTCs P0765, P0982 and/or P0983 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D . REPAIR the more specific DTC first. |
| P0769 | SSD Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D . |
| P0770 | SSE | DTC P0773 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E . REPAIR the more specific DTC first. |
| P0771 | SSE Performance/Stuck Off | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns. |
| P0772 | SSE Stuck On | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0773 | SSE Electrical | DTC P0770 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E . REPAIR the more specific DTC first. |
| P0774 | SSE Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E . |
| P07A5 | Transmission Friction Element "B" Stuck On | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P07A8 | Transmission Friction Element "D" Performance/Stuck Off | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P07A9 | Transmission Friction Element "D" Stuck On | DTC P0767 may set, CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P07AA | Transmission Friction Element "E" Performance/Stuck Off | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns. |
| P0815 | Upshift Switch Circuit | REFER to AUTOMATIC TRANSAXLE EXTERNAL CONTROLS . |
| P0816 | Downshift Switch Circuit | REFER to AUTOMATIC TRANSAXLE EXTERNAL CONTROLS . |
| P0867 | Transmission Fluid Pressure | CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART . |
| P0882 | TCM Power Input Signal Low | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to CHARGING SYSTEM . |
| P0883 | TCM Power Input Signal High | CLEAR the DTC. If the DTC returns, REFER to CHARGING SYSTEM . |
| P0960 | LPC A Control Circuit/Open | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I . REPAIR the more specific DTC first. |
| P0961 | LPC A Control Circuit Range/Performance | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I . |
| P0962 | LPC A Control Circuit Low | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I . REPAIR the more specific DTC first. |
| P0963 | LPC A Control Circuit High | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I . REPAIR the more specific DTC first. |
| P0973 | SSA Control Circuit Low | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A . REPAIR the more specific DTC first. |
| P0974 | SSA Control Circuit High | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A . REPAIR the more specific DTC first. |
| P0976 | SSB Control Circuit Low | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B . REPAIR the more specific DTC first. |
| P0977 | SSB Control Circuit High | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B . REPAIR the more specific DTC first. |
| P0979 | SSC Control Circuit Low | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C . REPAIR the more specific DTC first. |
| P0980 | SSC Control Circuit High | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C . REPAIR the more specific DTC first. |
| P0982 | SSD Control Circuit Low | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D . REPAIR the more specific DTC first. |
| P0983 | SSD Control Circuit High | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D . REPAIR the more specific DTC first. |
| P0984 | SSE Control Circuit Range/Performance | DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTCs returns, GO to SYMPTOM CHART for engagement concerns. |
| P1001 | KOER Not Able to Complete, KOER Aborted | RETRIEVE and RECORD all DTCs. REPAIR any self-test or continuous DTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the PCM to the latest calibration. RERUN the KOER self-test. If the DTC returns, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . After installing the new PCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to SOLENOID BODY STRATEGY DOWNLOAD . Road test the vehicle and PERFORM the SOLENOID BODY STRATEGY DRIVE CYCLE . |
| P1397 | System Voltage Out Of Self Test Range | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If the DTC returns, REFER to CHARGING SYSTEM . |
| P1501 | VSS Out Of Self Test Range | CLEAR the DTC. If the DTC returns, PLACE selector lever in park and monitor the VSS PID. VERIFY the VSS input is at 0. RERUN self-test procedure. If the DTC returns, REFER to ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL . |
| P1636 | Inductive Signature Chip Communication Error | CLEAR the DTC. If the DTC returns, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . After installing the new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to SOLENOID BODY STRATEGY DOWNLOAD . ROAD TEST the vehicle and PERFORM the SOLENOID BODY STRATEGY DRIVE CYCLE . |
| P163E | TCM Programming Error | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . After installing a new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to SOLENOID BODY STRATEGY DOWNLOAD . ROAD TEST the vehicle and PERFORM the SOLENOID BODY STRATEGY DRIVE CYCLE . |
| P163F | Transmission ID Block Corrupted, Not Programmed | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . After installing a new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to SOLENOID BODY STRATEGY DOWNLOAD . ROAD TEST the vehicle and PERFORM the SOLENOID BODY STRATEGY DRIVE CYCLE . |
| P1702 | TR Sensor Circuit Intermittent | DTCs P0706, P0707 and/or P0708 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J . REPAIR the more specific DTC first. |
| P1705 | TR Circuit Not Indicating Park/Neutral During Self Test | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1711 | TFT Sensor Out Of Self Test Range | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1744 | TCC Solenoid Circuit | DTC P1744 is a non-electrical DTC. CLEAR the DTC. If the DTCs returns, GO to SYMPTOM CHART for torque converter operation concerns/no apply. |
| P1780 | TCS (O/D Cancel) Circuit Out Of Self Test Range | REFER to AUTOMATIC TRANSAXLE EXTERNAL CONTROLS . |
| P1783 | Transmission Over Temperature Condition | MONITOR the TFT sensor PID and TCC PID. Road test the vehicle and MONITOR the TFT sensor and TCC solenoid electrical operation. If DTC P0741 is set, REPAIR DTC P0741 first. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART . |
| P1910 | Reverse Lamp Control Circuit/Open | CLEAR the DTC. If the DTC returns, REFER to EXTERIOR LIGHTING . |
| P1921 | TR Signal | Engine may not crank. DTCs P0706, P0707 and/or P0708 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J . REPAIR the more specific DTC first. |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | DTC P2700 is a non-electrical DTC. DTCs P0751 and/or P0752 may set. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns, no forward or delayed/soft forward and/or shift concerns/only gears 1, 2, 3, 4 available. |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | DTC P2701 is a non-electrical DTC. DTCs P0756 and/or P0757 may set. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/only gears 3 and 5 available. |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | DTC P2702 is a non-electrical DTC. DTCs P0761 and/or P0762 may set. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns, no 1-2 shift/harsh/soft/slipping or no 5-6 shift/harsh/soft/slipping or only gears 2 and 6 available. |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | DTC P2703 is a non-electrical DTC. DTCs P0766 and/or P0768 may set. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for engagement concerns/no reverse. |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | DTC P2704 is a non-electrical DTC. DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART engagement concerns/neutral after launch. |
| P2760 | TCC Pressure Control Solenoid Intermittent | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H . |
| P2783 | Torque Converter Temperature Too High | TCC control valve stuck in the apply position. CLEAR the DTC. If the DTC returns, GO to SYMPTOM CHART for torque converter operation concerns/no apply. |