Accessory Protocol Interface Module (APIM)
| DTC | Description | Action |
|---|---|---|
| C1001:01 | Video System Camera: General Electrical Failure | REFER to PARKING AID - VISUAL . |
| B108E:01 | Display: General Electrical Failure | GO to PINPOINT TEST H . |
| B116A:01 | Handset Microphone: General Electrical Failure | GO to PINPOINT TEST X . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to PINPOINT TEST D . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST D . |
| B1215:00 | External Memory Card: No Sub Type Information | GO to PINPOINT TEST AE . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1252:13 | USB Port: Circuit Open | GO to PINPOINT TEST E . |
| B12B8:11 | USB # 2 Port: Circuit Short to Ground |
NOTE:
This DTC refers to USB port #2 on the APIM itself, which is not used. INSPECT the APIM USB port #2 for damage and REMOVE any debris. CLEAR the DTCs. REPEAT the self-test. If DTC B12B8:11 is retrieved again, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM)
. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST Q . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information: No Sub Type Information | GO to PINPOINT TEST AF . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST R . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST H . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST S . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST T . |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES to retrieve and follow DTCs present in the IPC. |
| U1A00:87 | Private Communication Network: Missing Message | GO to PINPOINT TEST AK . |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2017:45 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2017:51 | Control Module Software #2: Not Programmed | PROGRAM the APIM. REFER to MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:51 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2017:52 | Control Module Software #2: Not Activated | PROGRAM the APIM. REFER to MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:52 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2017:54 | Control Module Software #2: Missing Calibration PROGRAM the APIM. | REFER to MODULE CONFIGURATION . CLEAR the DTC. REPEAT the self-test. If DTC U2017:54 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the APIM programming as directed by the scan tool. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - STANDARD , ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - MODULE REPLACEMENT or ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - CUSTOM . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the APIM programming as directed by the scan tool. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - STANDARD , ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - MODULE REPLACEMENT or ACCESSORY PROTOCOL INTERFACE MODULE (APIM) PROGRAMMING - CUSTOM . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST Y . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U3000:88 | Control Module: Bus Off | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:88 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST U . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST V . |
| B13DC:11 | Compact Disc Slot Illumination: Circuit Short To Ground | REFER to INSTRUMENT CLUSTER AND PANEL ILLUMINATION . |
| B13DC:12 | Compact Disc Slot Illumination: Circuit Short To Battery | REFER to INSTRUMENT CLUSTER AND PANEL ILLUMINATION . |
| B13DC:13 | Compact Disc Slot Illumination: Circuit Open | REFER to INSTRUMENT CLUSTER AND PANEL ILLUMINATION . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to PINPOINT TEST R . |
| U0257:87 | Lost Communication With Front Controls/Display Interface Module: Missing Message | GO to PINPOINT TEST W . |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES to retrieve and follow DTCs present in the IPC. |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST G . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. WAIT 10 seconds. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST U . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST V . |