Instrumentation, Message Center, And Warning Chimes DTCS: IPC
DTC CHART - IPC
| DTC | Description | Action |
|---|---|---|
| B1A14:11 | RCM Warning Lamp: Circuit Short To Ground | INSTALL a new IPC. REFER to INSTRUMENT PANEL CLUSTER (IPC) . DIAGNOSE all RCM DTCs. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| B1A14:13 | RCM Warning Lamp: Circuit Open | INSTALL a new IPC. REFER to INSTRUMENT PANEL CLUSTER (IPC) . DIAGNOSE all RCM DTCs. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| B1A84:41 | Car Configuration Data: General Checksum Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| B1A84:51 | Car Configuration Data: Not Programmed | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| C1D00:00 | Park Brake Apply Switch: No Sub Type Information | GO to PINPOINT TEST M . |
| C1D22:11 | Steering Wheel Switch Right Module: Circuit Short To Ground | Refer to the appropriate Information And Entertainment System for the procedure. |
| C1D22:23 | Steering Wheel Switch Right Module: Signal Stuck Low | Refer to the appropriate Information And Entertainment System for the procedure. |
| C2003:11 | Steering Wheel Switch Left Module: Circuit Short To Ground | GO to PINPOINT TEST AC . |
| C2003:23 | Steering Wheel Switch Left Module: Signal Stuck Low | GO to PINPOINT TEST AC . |
| P1607:81 | MIL Output Circuit: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data for powertrain data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM, BCM and other modules on the network. REFER to SECTION 3: SYMPTOM CHARTS or MULTIFUNCTION ELECTRONIC MODULES . |
| P1607:82 | MIL Output Circuit: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC does not receive an updated MIL request for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to PINPOINT TEST AT . If the DTC returns without DTC U0100:00, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . |
| P1607:87 | MIL Output Circuit: Missing Message | This DTC sets when the IPC does not receive the MIL request for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to PINPOINT TEST AT . If the DTC returns without DTC U0100:00, INSTALL a new PCM. REFER to ELECTRONIC ENGINE CONTROLS . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to PINPOINT TEST AA . |
| P1933:68 | Fuel Level Signal: Event Information | GO to PINPOINT TEST B . |
| U0073:00 | Control Module Communication Bus "A" Off: No Sub Type Information | REFER to MODULE COMMUNICATIONS NETWORK , No Medium Speed Controller Area Network (MS-CAN) - All Modules Not Responding. |
| U0074:00 | Control Module Communication Bus "B" Off: Bus Off: No Sub Type Information | REFER to MODULE COMMUNICATIONS NETWORK , No Infotainment Controller Area Network (I-CAN) - All Modules Not Responding. |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST AT . |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to PINPOINT TEST AU . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to PINPOINT TEST AV . |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to PINPOINT TEST AW . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AX . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AY . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub-Type Information | GO to PINPOINT TEST AZ . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST BA . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST BB . |
| U0208:00 | Lost Communication With "Seat Control Module B": No Sub Type Information | GO to PINPOINT TEST BC . |
| U0214:00 | Lost Communication With Remote Function Actuator: No Sub Type Information | GO to PINPOINT TEST BD . |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module-Left: No Sub Type Information | GO to PINPOINT TEST BE . |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module-Right: No Sub Type Information | GO to PINPOINT TEST BE . |
| U0252:00 | Lost Communication With Lighting Control Module-Rear "B": No Sub Type Information | GO to PINPOINT TEST BF . |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: Not Sub Type Information | GO to PINPOINT TEST BG . |
| U0264:00 | Lost Communication With Camera Module-Rear: No Sub Type Information | GO to PINPOINT TEST BH . |
| U0401:64 | Invalid Data Received from ECM/PCM A: Signal Plausibility Failure | This DTC sets when a message is temporarily undefined for longer than 2 seconds from the PCM for the ambient temperature, fuel economy, engine coolant temperature or engine rpm data. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the PCM. REFER to ELECTRONIC ENGINE CONTROLS . |
| U0415:64 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Plausibility Failure | This DTC sets when the wheel rotation count message is temporarily undefined for longer than 2 seconds from the ABS module for the odometer. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL . |
| U0420:68 | Invalid Data Received From Power Steering Control Module: Event Information | This DTC sets when data is invalid from the PSCM. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the PSCM. REFER to POWER STEERING . |
| U0422:00 | Invalid Data or Missing Data Received From Body Control Module: No Sub Type Information | This DTC sets when the fuel level, power mode or vehicle speed message are temporarily undefined for longer than 2 seconds or if the TPMS status message is missing for longer than 1, 250 milliseconds from the BCM. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U0422:68 | Invalid Data or Missing Data Received From Body Control Module: Event Information | This DTC sets when data is invalid from the BCM. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information This DTC sets when the temperature range data is invalid for longer than 2 seconds from the HVAC module through the BCM. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the HVAC module. | REFER to CLIMATE CONTROL SYSTEM - DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC sets when data is invalid from the RCM. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the RCM. REFER to SUPPLEMENTAL RESTRAINT SYSTEM . |
| U0558:00 | Invalid Data Received From Front Controls/Display Inteface Module: No Sub Type Information | This DTC sets when data is invalid from the FCDIM for longer than 2 seconds. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the FCDIM. Refer to the appropriate Information And Entertainment System for the procedure. |
| U0564:00 | Invalid Data Received From Speech Recognition Module: No Sub Type Information | This DTC sets when data is invalid from the APIM for longer than 2 seconds. CLEAR the DTC. REPEAT the self-test. If the DTC returns, RETRIEVE and REPAIR all DTCs set in the APIM. REFER to INFORMATION AND ENTERTAINMENT SYSTEMS - MONOCHROMATIC DISPLAY, 6 SPEAKERS or INFORMATION AND ENTERTAINMENT SYSTEMS - 4.2-INCH (107MM) SCREEN, 6 SPEAKERS . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2101:01 | Control Module Configuration Incompatible: General Electrical Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new IPC. REFER to INSTRUMENT PANEL CLUSTER (IPC) . |
| U3006:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to PINPOINT TEST BI . |
| U3006:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to PINPOINT TEST BJ . |