Instrumentation, Message Center And Warning Chimes DTCS: IPC

DTC DESCRIPTION - IPC

DTC	Description	Action
P0460:11	Fuel Level Sensor A Circuit: Circuit Short to Ground	GO to PINPOINT TEST B .
P0460:13	Fuel Level Sensor A Circuit: Circuit Open	GO to PINPOINT TEST B .
P1243:06	Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure	GO to PINPOINT TEST B .
P1346:11	Fuel Level Sensor B Circuit: Circuit Short to Ground	GO to PINPOINT TEST B .
P1346:13	Fuel Level Sensor B Circuit: Circuit Open	GO to PINPOINT TEST B .
P1534:01	Restraint Deployment Indicator Circuit: General Electrical Failure	INSTALL a new IPC . Refer to Instrument Panel Cluster (IPC) and diagnose all RCM DTCs. REFER to DTC CHART: RESTRAINT CONTROL MODULE (RCM) .
P1706:62	High Vehicle Speed Observed in Park: Signal Compare Failure	GO to PINPOINT TEST CK .
U0100:00	Lost Communication With ECM/PCM "A": No Sub-Type Information	GO to PINPOINT TEST AR .
U0101:00	Lost Communication With TCM: No Sub-Type Information	GO to PINPOINT TEST AS .
U0104:00	Lost Communication With Cruise Control Module: No Sub-Type Information	GO to PINPOINT TEST AT .
U0121:00	Lost Communication With ABS Control Module: No Sub-Type Information	GO to PINPOINT TEST AU .
U0131:00	Lost Communication With Power Steering Control Module: No Sub-Type Information	GO to PINPOINT TEST BX .
U0138:00	Lost Communication with All Terrain Control Module: No Sub-Type Information	GO to PINPOINT TEST BY .
U0140:00	Lost Communication With Body Control Module: No Sub-Type Information	GO to PINPOINT TEST AV .
U0151:00	Lost Communication With Restraints Control Module: No Sub-Type Information	GO to PINPOINT TEST AW .
U0154:00	Lost Communication With Occupant Classification Sensor (OCS): No Sub-Type Information	GO to PINPOINT TEST AX .
U0159:00	Lost Communication With Parking Assist Control Module "A": No Sub-Type Information	GO to PINPOINT TEST AY .
U0212:00	Lost Communication With Steering Column Control Module: No Sub-Type Information	GO to PINPOINT TEST AZ .
U023A:00	Lost Communication With Image Processing Module A: No Sub-Type Information	GO to PINPOINT TEST DK .
U0241:00	Lost Communication With Headlamp Control Module "A": No Sub-Type Information	GO to PINPOINT TEST BA .
U0253:00	Lost Communication With Accessory Protocol Interface Module: No Sub-Type Information	GO to PINPOINT TEST BB .
U0401:00	Invalid Data Received From ECM/PCM A: No Sub-Type Information	This DTC sets when the IPC receives invalid network data for the cruise control, odometer count, fuel alcohol percent, tachometer, temperature and AWD lock torque from the PCM . RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to ELECTRONIC ENGINE CONTROLS .
U0401:81	Invalid Data Received From ECM/PCM A: Invalid Serial Data Received	This DTC sets when the IPC receives invalid network data for temperature and vehicle speed from the PCM . RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to ELECTRONIC ENGINE CONTROLS .
U0402:00	Invalid Data Received from TCM: No Sub-Type Information	This DTC sets when the IPC receives invalid network data for the transmission range input from the PCM . RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to ELECTRONIC ENGINE CONTROLS .
U0405:56	Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid network data for adaptive cruise control from the PCM . CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0415:56	Invalid Data Received From ABS Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives invalid data for stability traction control configuration or trailer sway configuration from the ABS module. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0422:00	Invalid Data Received From	Body Control Module: No Sub-Type Information This DTC sets when the IPC receives invalid data for brake fluid level or tire pressure from the BCM . RETRIEVE and REPAIR all non-network DTCs in the BCM . REFER to MULTIFUNCTION ELECTRONIC MODULES .
U0422:56	Invalid Data Received From Body Control Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives BCM data for the autolamp function and IPC is not configured for autolamps. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0424:00	Invalid Data Received From HVAC Control Module: No Sub Type Information	This DTC sets when the IPC receives unknown outside air temperature data from the HVAC module. RETRIEVE and REPAIR all non-network DTCs in the PCM and the HVAC module. REFER to CLIMATE CONTROL SYSTEM - EMTC and ELECTRONIC ENGINE CONTROLS .
U0424:81	Invalid Data Received From HVAC Control Module: Invalid Serial Data Received	This DTC sets when the IPC receives invalid outside air temperature data from the HVAC module. RETRIEVE and REPAIR all non-network DTCs in the PCM and the HVAC module. REFER to CLIMATE CONTROL SYSTEM - EMTC and ELECTRONIC ENGINE CONTROLS .
U0424:82	Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated	GO to PINPOINT TEST BC .
U0452:00	Invalid Data Received From Restraints Control Module: No Sub Type Information	This DTC sets when the IPC receives invalid data for the Belt-Minder® from the Restraints Control Module (RCM) module. RETRIEVE and REPAIR all non-network DTCs in the RCM . REFER to SUPPLEMENTAL RESTRAINT SYSTEM .
U045A:00	Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information	This DTC sets when the IPC receives invalid data for parking aid and active park assist from the PAM . RETRIEVE and REPAIR all non-network DTCs in the PAM . REFER to PARKING AID SYSTEM .
U045A:56	Invalid Data Received From Parking Assist Control Module "A": Invalid/Incompatible Configuration	This DTC sets when the IPC configuration for parking aid does not match the data received. NOTE: The IPC does not display the parking aid settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U045A:81	Invalid Data Received From Parking Assist Control Module "A": Invalid Serial Data Received	This DTC sets when the IPC receives invalid rear parking aid data from the PAM . The IPC is not configured for parking aid. NOTE: The IPC does not display the check mark in the parking aid settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U046B:86	Invalid Data Received From Global Positioning System Module: Signal Invalid	This DTC sets when the IPC receives invalid compass data from the APIM . NOTE: The compass displays dashes (- -) or is blank depending on the display mode. RETRIEVE and REPAIR all non-network DTCs in the APIM . REFER to INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM - PREMIUM PLUS or INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM - SONY SOUND .
U0531:56	Invalid Data Received From Rear Gate Module: Invalid/Incompatible Configuration	This DTC sets when the IPC receives rear liftgate data from the LTM when the IPC is not configured for rear liftgate or if the IPC does not receive expected liftgate data when it is configured for rear liftgate. NOTE: The IPC does not display the power liftgate settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0533:56	Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration	This DTC sets when the IPC receives blind spot or side obstacle detection data when the IPC is not configured for BLIS® or if the IPC does not receive blind spot or side obstacle detection data when it is configured for BLIS® . NOTE: The IPC does not display the BLIS® or CTA settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0533:82	Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated	This DTC sets in the IPC when the side obstacle detection data remains unchanged from the SOD-L for more than 1.6 seconds. NOTE: The IPC displays a fault warning message and does not display the check mark in the BLIS® settings in the message center. RETRIEVE and REPAIR all non-network DTCs in the SOD-L. SIDE AND REAR VISION .
U0534:56	Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration	This DTC sets when the IPC receives blind spot or side obstacle detection data when the IPC is not configured for BLIS® or if the Instrument Panel Cluster (IPC) does not receive blind spot or side obstacle detection data when it is configured for BLIS® . NOTE: The IPC does not display the BLIS® or CTA settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U0534:82	Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated	This DTC sets in the IPC when the side obstacle detection data remains unchanged from the SOD-R for more than 1.6 seconds. NOTE: The IPC displays a fault warning message and does not display the check mark in the BLIS® settings in the message center. RETRIEVE and REPAIR all non-network DTCs in the SOD-R . SIDE AND REAR VISION .
U0554:00	Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information	This DTC sets when the IPC receives invalid clock data from the APIM for more than 5 seconds. NOTE: The IPC displays all dashes (- -) for the time of day. RETRIEVE and REPAIR all non-network DTCs in the APIM . REFER to INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM - PREMIUM PLUS or INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM - SONY SOUND .
U1018:00	Lost Communication With Generic Function Module: No Sub Type Information	GO to PINPOINT TEST DJ .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. REFER to MODULE CONFIGURATION SYSTEM , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U3000:41	Control Module: General Checksum Failure	CLEAR the DTCs . REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new IPC . Refer to Instrument Panel Cluster (IPC) .
U3000:43	Control Module: Special Memory Failure	CLEAR the DTCs . REPEAT the self-test. If DTC U3000:43 is retrieved again, INSTALL a new IPC . Refer to Instrument Panel Cluster (IPC) .
U3000:44	Control Module: Data Memory Failure	CLEAR the DTCs . REPEAT the self-test. If DTC U3000:44 is retrieved again, INSTALL a new IPC . Refer to Instrument Panel Cluster (IPC) .
U3000:45	Control Module: Program Memory Failure	CARRY OUT the PMI procedure as directed by the scan tool (refer to MODULE CONFIGURATION SYSTEM , PMI for further information). CLEAR the DTCs . REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new IPC . Refer to Instrument Panel Cluster (IPC) .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST BD .
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST BE .
U300A:64	Ignition Switch: Signal Plausibility Failure	DTC U300A:64 sets on-demand and in continuous memory when the IPC detects a messaged START input for 15 seconds or more. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. REFER to STEERING COLUMN SWITCHES to diagnose the ignition start circuit to the BCM .