Supplemental Restraint System DTCS: OCSM
DTC DESCRIPTION - OCSM
| DTC | Description | Action |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short To Ground | GO to PINPOINT TEST Z . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short To Battery | GO to PINPOINT TEST Z . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to PINPOINT TEST Z . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range | GO to PINPOINT TEST Z . |
| B0061:49 | Passenger Seatbelt Tension Sensor: Internal Electronic Failure | GO to PINPOINT TEST Z . |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:1A | Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:11 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Ground | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:12 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Battery | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:49 | Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to PINPOINT TEST AA . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to PINPOINT TEST AA . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | This DTC indicates the vehicle has been in a crash. CLEAR the OCSM DTCs and REPEAT the self-test. If DTC B1193:00 returns, INSTALL a new OCS sensor. Refer to INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT . |
| U0100:00 | Lost Communication with ECM/PCM A: No Sub Type Information | GO to PINPOINT TEST AO . |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AP . |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | CARRY OUT the PCM self-test. REFER to the ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) (SECTION 0) and ENGINE CONTROLS - POWERTRAIN DTC CHARTS & DESCRIPTIONS (EXCEPT DIESEL & HYBRID) (SECTION 4) . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:54 | Control Module: Missing Calibration | Using a scan tool, CARRY OUT the OCS
Reset. FOLLOW all instructions on the scan tool. If the OCS Reset was not successful, VERIFY correct installation of the OCS . VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the self-test. If DTC U3000:54 is still present, INSTALL a new OCS sensor. Refer to OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST Y . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST Y . |