Audio Front Control Module (ACM)
AUDIO FRONT CONTROL MODULE (ACM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure |
|
| B1A01:11 | Speaker #1: Circuit Short to Ground |
|
| B1A01:12 | Speaker #1: Circuit Short to Battery |
|
| B1A01:13 | Speaker #1: Circuit Open |
|
| B1A02:01 | Speaker #2: General Electrical Failure |
|
| B1A02:11 | Speaker #2: Circuit Short to Ground |
|
| B1A02:12 | Speaker #2: Circuit Short to Battery |
|
| B1A02:13 | Speaker #2: Circuit Open |
|
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST J . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST J . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST J . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST J . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST K . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST K . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST K . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST K . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. Therefore, tests ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure |
|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST AF . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AL . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to PINPOINT TEST AM . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2014:96 | Control Module Hardware: Component Internal Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:96 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to AUDIO CONTROL MODULE (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AN . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AO . |