Front Control Interface Module (FCIM)

FCIM DTC CHART

DTC	Description	Action
B00D5:01	Restraint System Passenger Disable Indicator: General Electrical Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B00D5:01 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
B113C:11	Hazard switch illumination: Circuit Short To Ground	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B113C:11 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
B1202:01	Restraint System Passenger Enable Indicator: General Electrical Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B1202:01 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
U0155:00	Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information	GO to PINPOINT TEST AF .
U0257:00	Lost Communication With Front Controls / Display Interface Module: No Sub Type Information	GO to PINPOINT TEST AL .
U0423:00	Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information	RETRIEVE and FOLLOW DTCs present in the IPC. REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES .
U2013:63	Switch Pack: Circuit / Component Protection Time-Out	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U2013:63 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
U3000:41	Control Module: General Checksum Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
U3000:42	Control Module: General Memory Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST AM .
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST AN .
U0100:00	Lost Communication with ECM/PCM "A": No Sub Type Information	GO to PINPOINT TEST AC .
U0140:00	Lost Communication With Body Control Module: No Sub Type Information: No Sub Type Information	GO to PINPOINT TEST AD .
U0155:00	Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information	GO to PINPOINT TEST AF .
U0401:00	Invalid Data Received from ECM/PCM A: No Sub Type Information	RETRIEVE and FOLLOW DTCs present in the PCM. REFER to ELECTRONIC ENGINE CONTROLS .
U0422:00	Invalid Data Received From Body Control Module: No Sub Type	Information RETRIEVE and FOLLOW DTCs present in the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES .
U0423:00	Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information	RETRIEVE and FOLLOW DTCs present in the IPC. REFER to INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. For more information, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION SYSTEM . If there have been no recent service actions, INSTALL a new Global Positioning System Module (GPSM) to correct the failure to retain configuration data. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:09	Control Module: Component Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, PERFORM a battery reset by disconnecting the battery for 5 minutes, then reconnecting it. CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:41	Control Module: General Checksum Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:42	Control Module: General Memory Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new Global Positioning System Module (GPSM). REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST AM .
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST AN .