LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2013 >> Fusion Energi Titanium >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Pinpoint Tests (Hybrid) >> Pinpoint Test QF: Electronic Throttle Control (Etc) System >> Test Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Procedure

  1. QF1 CHECK FOR DTCS 

    Are any DTCs present other than P0600, P060A, P060B, P060C, P060D, P061A, P061F, P1674, or U0300? 

    Yes No
    DISREGARD the current diagnostic trouble code (DTC) at this time. DIAGNOSE the next DTC. GO to DIAGNOSTIC TROUBLE CODE (DTC) CHARTS AND DESCRIPTIONS . For DTC P060B, GO to  QF4.
    For DTCs P061A or P061F, GO to  QF6.
    For all others, GO to QF2  .
  2. QF2 CHECK THE PCM VOLTAGE CIRCUITS FOR AN OPEN 
    • Ignition OFF.
    • PCM connector disconnected.
    • Connect a 5 amp fused jumper wire between the following:
      Point A PCM Connector, Harness Side Point B
      PCMRC - Pin B1 Ground
    • Ignition ON, engine OFF.
    • Measure the voltage between:
      (+) PCM Connector, Harness Side (-)
      VPWR - Pin B11, B12 Ground

    Is the voltage greater than 10.5 V? 

    Yes No
    GO to QF3  . REPAIR the open circuit. Clear the PCM DTCs.
    REPEAT the self-test.
  3. QF3 CHECK THE PCM FOR THE LATEST CALIBRATION 
    • Ignition OFF.
    • Remove the jumper wire(s).
    • PCM connector connected.
    • Program the PCM to the latest calibration.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Ignition OFF.
    • Ignition ON, engine running.
    • Use the customer information to recreate the concern.
    • Carry out the PCM self-test.

    Are DTCs P0600, P060A, P060C, P060D, P1674 or U0300 present? 

    Yes No
    GO to  QF7. The concern is not present at this time. If a driveabilty concern exists,
    RETURN to ENGINE CONTROLS - SYMPTOM CHARTS (HYBRID) , Symptom Charts for further direction.
  4. QF4 CHECK FOR REFERENCE VOLTAGE CONCERNS 
    • Inspect the PCM harness for damage.
    • Verify the correct operation of the sensors using ETCREF, VREF and related circuits. GO to PINPOINT TEST C  and follow the pinpoint test direction.

    Is a concern present? 

    Yes No
    REPAIR as necessary.
    Clear the PCM DTCs. REPEAT the self-test.    		 GO to QF5  .
  5. QF5 CHECK FOR AN INTERMITTENT CONCERN 
    • Clear the PCM DTCs.
    • Carry out the PCM self-test.

    Is DTC P060B present? 

    Yes No
    GO to  QF7. The concern is not present at this time.
  6. QF6 VERIFY THE CUSTOMER CONCERN 
    • Clear the PCM DTCs.
    • Use the customer information to recreate the concern.
    • Carry out the PCM self-test.

    Are DTCs P061A or P061F present? 

    Yes No
    RESET the keep alive memory (KAM). REFER to RESETTING THE KEEP ALIVE MEMORY (KAM) .
    GO to QF7  .    		 The concern is not present at this time.
  7. QF7 CHECK FOR CORRECT PCM OPERATION 
    • Disconnect all the PCM connectors.
    • Visually inspect for:
      • pushed out pins
      • corrosion
    • Connect all the PCM connectors and make sure they seat correctly.
    • Carry out the PCM self-test.
    • Verify the concern is still present.

    Is the concern still present? 

    Yes No
    INSTALL a new PCM. REFER to FLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM) , Programming the VID Block for a Replacement PCM. The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
scientia non olet · About LEMON Manuals