MULTIFUNCTION Electronic Modules DTCS: RFA
RFA DTC CHART
| DTC | Description | Action |
|---|---|---|
| B108A:12 | Start Button: Circuit Short To Battery | GO to PINPOINT TEST K . |
| B10AB:06 | Remote Keyless Entry Synchronization: Algorithm Based Failure | GO to PINPOINT TEST J . |
| B10C6:01 | Exterior Trunk Antenna: General Electrical Failure | GO to PINPOINT TEST I . |
| B10C7:01 | Interior Trunk Antenna: General Electrical Failure | GO to PINPOINT TEST D . |
| B10C8:01 | Interior Centre Antenna: General Electrical Failure | GO to PINPOINT TEST D . |
| B10C9:01 | Interior Front Antenna: General Electrical Failure | GO to PINPOINT TEST D . |
| B10D7:05 | PATS Key: System Programming Failure | GO to PINPOINT TEST A . |
| B10D7:31 | PATS Key: No Signal | This DTC sets during an RFA module self-test if 2 programmed Intelligent Access (IA) keys are not detected inside the vehicle. CHECK each IA key individually to see if it operates the vehicle. If 2 programmed IA keys are not present inside the vehicle, DISREGARD this DTC . |
| B10D8:51 | PATS Key Less Than Minimum Programmed: Not Programmed | If other PATS DTCs are present, address them first. If DTC B10D8:51 is the only DTC present, PROGRAM additional keys (minimum of 2 keys must be programmed). REFER to KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT . |
| B10D9:11 | PATS Transponder: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B10D9:12 | PATS Transponder: Circuit Short To Battery | GO to PINPOINT TEST B . |
| B10D9:31 | PATS Transponder: No Signal | GO to PINPOINT TEST B . |
| B10D9:87 | PATS Transponder: Missing Message | GO to PINPOINT TEST B . |
| B10DA:51 | PATS Target Identifier: Not Programmed | There is no PCM identification stored in the RFA module. CARRY OUT a parameter reset, then CYCLE the ignition and make an attempt to start the vehicle. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET . |
| B10DA:61 | PATS Target Identifier: Signal Calculation Failure | There is an incorrect PCM ID stored in the RFA module. CARRY OUT a parameter reset, then CYCLE the ignition and make an attempt to start the vehicle. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET . |
| B113E:11 | External Boot/Trunk Release Switch: Circuit Short To Ground | GO to PINPOINT TEST I . |
| B11C6:01 | Passenger Door External Antenna: General Electrical Failure | GO to PINPOINT TEST H . |
| B11CA:01 | Driver Door External Antenna: General Electrical Failure | GO to PINPOINT TEST H . |
| B121A:11 | Keypad Illumination Output: Circuit Short To Ground | GO to PINPOINT TEST G . |
| B121A:15 | Keypad Illumination Output: Circuit Short To Battery or Open | GO to PINPOINT TEST G . |
| B121B:11 | Keypad Input Switch: Circuit Short To Ground | GO to PINPOINT TEST F . |
| B1381:11 | Left Front Door Handle Proximity Sensor: Circuit Short To Ground | GO to PINPOINT TEST H . |
| B1381:15 | Left Front Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to PINPOINT TEST H . |
| B1381:29 | Left Front Door Handle Proximity Sensor: Signal Invalid | CLEAR the DTCs . REPEAT the self-test. If DTC B1381:29 returns, INSTALL a new LF exterior door handle. REFER to EXTERIOR DOOR HANDLE . |
| B1382:11 | Right Front Door Handle Proximity Sensor: Circuit Short To Ground | GO to PINPOINT TEST H . |
| B1382:15 | Right Front Door Handle Proximity Sensor: Circuit Short To Battery or Open | GO to PINPOINT TEST H . |
| B1382:29 | Right Front Door Handle Proximity Sensor: Signal Invalid | CLEAR the DTCs . REPEAT the self-test. If DTC B1382:29 returns, INSTALL a new LF exterior door handle. REFER to EXTERIOR DOOR HANDLE . |
| P1571:12 | Brake Switch: Circuit Short To Battery | GO to PINPOINT TEST O . |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST D . |
| U1000:00 | Solid State Driver Protection Active - Driver Disabled: No Sub Type Information | GO to PINPOINT TEST AL . |
| U201F:31 | External Receiver: No Signal | GO to PINPOINT TEST C . |
| U201F:56 | External Receiver: Invalid/Incompatible Configuration | CARRY OUT the PMI procedure as directed by the scan tool (REFER to MODULE CONFIGURATION , PMI for further information). CLEAR the DTCs . REPEAT the self-test. If DTC U201F:56 is retrieved again, INSTALL a new RFA . REFER to REMOTE FUNCTION ACTUATOR (RFA) MODULE . |
| U2100:55 | Initial Configuration Not Complete: Not Configured | CARRY OUT the PMI procedure as directed by the scan tool (REFER to MODULE CONFIGURATION , PMI for further information). CLEAR the DTCs . REPEAT the self-test. If DTC U2100:55 is retrieved again, INSTALL a new RFA . REFER to REMOTE FUNCTION ACTUATOR (RFA) MODULE . |
| U3000:49 | Control Module: Internal Electronic Failure | DIAGNOSE all other DTCs first. If no other DTCs are present, INSTALL a new RFA module. REFER to REMOTE FUNCTION ACTUATOR (RFA) MODULE . |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to PINPOINT TEST J . |