Common Specifications & Procedures
FLEX COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Refer to SPECIFICATIONS | ||
| Torque | Refer to SPECIFICATIONS | ||
| Auxiliary Air Conditioning | |||
| Service | Refer to SPECIFICATIONS | ||
| Torque | Refer to SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 258 Ft. Lbs. (350 N.m) | ||
| Rear | 258 Ft. Lbs. (350 N.m) | ||
| Battery | Refer to SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | R/R, L/R, R/F, L/F BRAKE SYSTEM BLEEDING | ||
| Front Disc Brakes w/Torque | SPECIFICATIONS | ||
| Rear Disk Brakes w/Torque | SPECIFICATIONS | ||
| Charging | |||
| Generator w/Torque | SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | SPECIFICATIONS | ||
| Belt Routing | ACCESSORY DRIVE | ||
| Engine Cooling | |||
| General Service Specifications | Refer to SPECIFICATIONS | ||
| Radiator Cap Pressure | 14 psi (96 kPa) | ||
| Thermostat R & I | THERMOSTAT -- 3.5L TI-VCT or THERMOSTAT -- 3.5L GTDI | ||
| Water Pump R & I | COOLANT PUMP -- 3.5L TI-VCT or COOLANT PUMP -- 3.5L GTDI . | ||
| Engine Mechanical | |||
| 3.5L V6 Ti-VCT | |||
| Compression | SPECIFICATIONS | ||
| Oil Pressure @ 1, 500 RPM (engine at normal operating temperature) | Minium 30 psi (205 kPa) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | SPECIFICATIONS | ||
| 3.5L GTDI V6 | |||
| Compression | SPECIFICATIONS | ||
| Oil Pressure @1, 500 RPM (engine at normal operating temperature) | Minimum 30 psi (205 kPa) | ||
| Overhaul | Refer to SPECIFICATIONS | ||
| Torque | Refer to Torque SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | 59 Ft. Lbs. (80 N.m) | ||
| 3.5L V6 Ti-VCT | Refer to FLEXPLATE for sequence. | ||
| 3.5L GTDI V6 | Refer to FLEXPLATE for sequence. | ||
| Fuel System | |||
| Fuel Filter Location | Vehicle has a lifetime fuel filter which is serviced as part of the Fuel Pump (FP) module. | ||
| Fuel Filter R & I | FUEL PUMP MODULE | ||
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Pressure Specifications | |||
| 3.5L Ti-VCT | 55 psi (379 kPa) Key ON Engine Running (KOER) 55 psi (379 kPa) Key ON Engine OFF (KOEO) |
||
| 3.5L GTDI | 51-75 psi (350 kPa-520kPa) Key ON Engine Running (KOER) 55 psi (379 kPa) Key ON Engine OFF (KOEO) |
||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST . | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires | Engine has coil-on-plug ignition. | ||
| Spark Plugs | |||
| 3.5L V6 Ti-VCT | |||
| Type | CYFS 12F 5 | ||
| Gap | .051 In. (1.30 mm) | ||
| Torque | 133 In. Lbs. (15 N.m) | ||
| 3.5L GTDI V6 | |||
| Type | CYFS 12 YT3 | ||
| Gap | .032-.038 In. (0.81-0.97 mm) | ||
| Torque | 133 In. Lbs. (15 N.m) | ||
| Starting | |||
| Starter w/Torque | Refer to Torque SPECIFICATIONS . | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to SPECIFICATIONS . | ||
| Torque | Refer to Torque SPECIFICATIONS . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (135 N.m) | ||