Vehicle Dynamic Suspension DTCS
VDM DTC CHART
| DTCs | Description | Action |
|---|---|---|
| C110C:11 | Left Front Damper Solenoid: Circuit Shorted to Ground | GO to PINPOINT TEST D . |
| C110C:12 | Left Front Damper Solenoid: Circuit Shorted to Battery | GO to PINPOINT TEST D . |
| C110C:13 | Left Front Damper Solenoid: Circuit Open | GO to PINPOINT TEST D . |
| C110D:11 | Right Front Damper Solenoid: Circuit Shorted to Ground | GO to PINPOINT TEST D . |
| C110D:12 | Right Front Damper Solenoid: Circuit Shorted to Battery | GO to PINPOINT TEST D . |
| C110D:13 | Right Front Damper Solenoid: Circuit Open | GO to PINPOINT TEST D . |
| C110E:11 | Left Rear Damper Solenoid: Circuit Shorted to Ground | GO to PINPOINT TEST D . |
| C110E:12 | Left Rear Damper Solenoid: Circuit Shorted to Battery | GO to PINPOINT TEST D . |
| C110E:13 | Left Rear Damper Solenoid: Circuit Open | GO to PINPOINT TEST D . |
| C110F:11 | Right Rear Damper Solenoid: Circuit Shorted to Ground | GO to PINPOINT TEST D . |
| C110F:12 | Right Rear Damper Solenoid: Circuit Shorted to Battery | GO to PINPOINT TEST D . |
| C110F:13 | Right Rear Damper Solenoid: Circuit Open | GO to PINPOINT TEST D . |
| U0001:88 | High Speed CAN Communications Bus: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |
| U0100:87 | Lost Communication with ECM /PCM A: Missing Message | GO to PINPOINT TEST E . |
| U0121:87 | Lost Communication with ABS Control Module: Missing Message | GO to PINPOINT TEST F . |
| U0155:87 | Lost Communication with IPC : Missing Message | GO to PINPOINT TEST G . |
| U0401:00 | Invalid Data Received from ECM /PCM A: No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM. REFER to ELECTRONIC ENGINE CONTROLS . |
| U0415:00 | Invalid Data Received from ABS Control Module: No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the ABS module. RETRIEVE and REPAIR all non-network DTCs in the ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL . |
| U0423:00 | Invalid Data Received from IPC : No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the IPC . RETRIEVE and REPAIR all non-network DTCs in the IPC . REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the service history for recent service actions related to the VDM
module. This DTC sets due to incomplete or improper module configuration. If there have been recent service actions with this module, REPEAT the PMI using as-built data. If there have been no recent service actions INSTALL a new VDM module. REFER to VEHICLE DYNAMICS MODULE (VDM) . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the DTC. CARRY OUT the VDM
module self-test. RETRIEVE and RECORD all DTCs. If the DTC returns, INSTALL a new VDM module. REFER to VEHICLE DYNAMICS MODULE (VDM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST A . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST B . |