Vehicles With Am/Fm/Cd/Sync/Touchscreen: ACM

DTC INDEX

DTC	Description	Action
B1A01:01	Speaker #1: General Electrical Failure	For a LHF door speaker concern, GO to PINPOINT TEST H For a LH instrument panel tweeter speaker concern, GO to PINPOINT TEST I
B1A01:11	Speaker #1: Circuit Short To Ground	For a LHF door speaker concern, GO to PINPOINT TEST H For a LH instrument panel tweeter speaker concern, GO to PINPOINT TEST I
B1A01:12	Speaker #1: Circuit Short To Battery	For a LHF door speaker concern, GO to PINPOINT TEST H For a LH instrument panel tweeter speaker concern, GO to PINPOINT TEST I
B1A01:13	Speaker #1: Circuit Open	For a LHF door speaker concern, GO to PINPOINT TEST H For a LH instrument panel tweeter speaker concern, GO to PINPOINT TEST I
B1A02:01	Speaker #2: General Electrical Failure	For a RHF door speaker concern, GO to PINPOINT TEST J For a RH instrument panel tweeter speaker concern, GO to PINPOINT TEST K
B1A02:11	Speaker #2: Circuit Short To Ground	For a RHF door speaker concern, GO to PINPOINT TEST J For a RH instrument panel tweeter speaker concern, GO to PINPOINT TEST K
B1A02:12	Speaker #2: Circuit Short To Battery	For a RHF door speaker concern, GO to PINPOINT TEST J For a RH instrument panel tweeter speaker concern, GO to PINPOINT TEST K
B1A02:13	Speaker #2: Circuit Open	For a RHF door speaker concern, GO to PINPOINT TEST J For a RH instrument panel tweeter speaker concern, GO to PINPOINT TEST K
B1A03:01	Speaker #3: General Electrical Failure	GO to PINPOINT TEST L
B1A03:11	Speaker #3: Circuit Short To Ground	GO to PINPOINT TEST L
B1A03:12	Speaker #3: Circuit Short To Battery	GO to PINPOINT TEST L
B1A03:13	Speaker #3: Circuit Open	GO to PINPOINT TEST L
B1A04:01	Speaker #4: General Electrical Failure	GO to PINPOINT TEST M
B1A04:11	Speaker #4: Circuit Short To Ground	GO to PINPOINT TEST M
B1A04:12	Speaker #4: Circuit Short To Battery	GO to PINPOINT TEST M
B1A04:13	Speaker #4: Circuit Open	GO to PINPOINT TEST M
B1A56:21	Antenna: Signal Amplitude < Minimum	If DTC B1A56:21 sets after running the bezel diagnostic tests, DISREGARD this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail.
B1A89:11	Satellite Antenna: Circuit Short To Ground	For a satellite radio concern, GO to PINPOINT TEST B For a SIRIUS Data Services concern, GO to PINPOINT TEST C
B1A89:13	Satellite Antenna: Circuit Open	For a satellite radio concern, GO to PINPOINT TEST B For a SIRIUS Data Services concern, GO to PINPOINT TEST C
B1D19:49	Compact Disc Unit: Internal Electronic Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to: AUDIO UNIT .
B1D19:4B	Compact Disc Unit: Over Temperature	The ACM was over temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTC. This is normal operation.
U0155:00	Lost Communication With IPC Control Module: No Sub Type Information	GO to PINPOINT TEST AF
U0253:00	Lost Communication With Accessory Protocol Interface Module: No Sub Type Information	GO to PINPOINT TEST AK
U0256:00	Lost Communication With Front Controls Interface Module "A": No Sub Type Information	GO to PINPOINT TEST AL
U0257:00	Lost Communication With Front Control/Display Interface Module: No Sub Type Information	NOTE: Despite the description, this DTC applies to the FDIM, not the FCDIM. GO to PINPOINT TEST AM
U201A:51	Control Module Main Calibration Data: Not Programmed	This DTC sets due to an incomplete or incorrect ACM PMI. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, REPEAT/PERFORM the ACM PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PMI . If there have been no recent service actions, the ACM has failed to retain configuration data. INSTALL a new ACM. REFER to: AUDIO UNIT .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	This DTC sets due to an incomplete or incorrect ACM PMI. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, REPEAT/PERFORM the ACM PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PMI . If there have been no recent service actions, the ACM has failed to retain configuration data. INSTALL a new ACM. REFER to: AUDIO UNIT .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	This DTC sets due to an incomplete or incorrect ACM PMI. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, REPEAT/PERFORM the ACM PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PMI . If there have been no recent service actions, the ACM has failed to retain configuration data. INSTALL a new ACM. REFER to: AUDIO UNIT .
U3000:41	Control Module: General Checksum Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. REFER to: AUDIO UNIT .
U3000:42	Control Module: General Memory Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. REFER to: AUDIO UNIT .
U3000:96	Control Module: Component Internal Failure	CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. REFER to: AUDIO UNIT .
U3003:16	Battery Voltage: Circuit Voltage Below Threshold	GO to PINPOINT TEST AO
U3003:17	Battery Voltage: Circuit Voltage Above Threshold	GO to PINPOINT TEST AP