Information System And Entertainment System (W/ Touchscreen) DTCS: APIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B108E:01 | Display: General Electrical Failure | GO to Pinpoint Test AC |
| B116A:01 | Handset Microphone: General Electrical Failure | GO to Pinpoint Test T |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out Of Range | GO to Pinpoint Test Z |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to Pinpoint Test Z |
| B1215:00 | External Memory Card: No Sub Type Information | GO to Pinpoint Test AD |
| B1252:11 | USB Port: Circuit Short To Ground | For an inoperative USB port, GO to Pinpoint Test V For an inoperative Secure Digital (SD) card slot, GO to Pinpoint Test W |
| B1252:13 | USB Port: Circuit Open | For an inoperative USB port, GO to Pinpoint Test V For an inoperative Secure Digital (SD) card slot, GO to Pinpoint Test W |
| B12B8:11 | USB Port #2: Circuit Short To Ground |
NOTE:
This DTC refers to USB port #2 on the APIM itself, which is not used. INSPECT the APIM USB port #2 for damage and REMOVE any debris.CLEAR the Diagnostic Trouble Codes (DTCs).WAIT at least 10 seconds.REPEAT the self-test.If DTC B12B8:11 is retrieved again, Refer to APIM HARDWARE TESTING
. |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . See The Rear Video Is Inoperative. |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AJ |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AK |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to Pinpoint Test AC |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test AO |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AP |
| U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AT |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. REFER to: Instrumentation, Message Center and Warning Chimes . |
| U1A00:87 | Private Communication Network: Missing Message | GO to Pinpoint Test C |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U2017:45 is retrieved again, Refer to APIM HARDWARE TESTING . |
| U2017:51 | Control Module Software #2: Not Programmed | CHECK vehicle service history for recent service actions related to the APIM. This DTC sets due to incomplete or incorrect PMI (Programmable Module Installation) procedures. If there have been recent service actions with the APIM, REPEAT/PERFORM the APIM programming as directed by the diagnostic scan tool. REFER to: Information and Entertainment System - System Operation and Component Description . See APIM Programming. If there have been no recent service actions, Refer to APIM HARDWARE TESTING . |
| U2017:52 | Control Module Software #2: Not Activated | CHECK vehicle service history for recent service actions related to the APIM. This DTC sets due to incomplete or incorrect PMI (Programmable Module Installation) procedures. If there have been recent service actions with the APIM, REPEAT/PERFORM the APIM programming as directed by the diagnostic scan tool. REFER to: Information and Entertainment System - System Operation and Component Description . See APIM Programming. If there have been no recent service actions, Refer to APIM HARDWARE TESTING . |
| U2017:54 | Control Module Software #2: Missing Calibration | CHECK vehicle service history for recent service actions related to the APIM. This DTC sets due to incomplete or incorrect PMI (Programmable Module Installation) procedures. If there have been recent service actions with the APIM, REPEAT/PERFORM the APIM programming as directed by the diagnostic scan tool. REFER to: Information and Entertainment System - System Operation and Component Description . See APIM Programming. If there have been no recent service actions, Refer to APIM HARDWARE TESTING . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to the APIM. This DTC sets due to incomplete or incorrect PMI (Programmable Module Installation) procedures. If there have been recent service actions with the APIM, REPEAT/PERFORM the APIM programming as directed by the diagnostic scan tool. REFER to: Information and Entertainment System - System Operation and Component Description . See APIM Programming. If there have been no recent service actions, Refer to APIM HARDWARE TESTING . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to the APIM. This DTC sets due to incomplete or incorrect PMI (Programmable Module Installation) procedures. If there have been recent service actions with the APIM, REPEAT/PERFORM the APIM programming as directed by the diagnostic scan tool. REFER to: Information and Entertainment System - System Operation and Component Description . See APIM Programming. If there have been no recent service actions, Refer to APIM HARDWARE TESTING . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:04 is retrieved again, Refer to APIM HARDWARE TESTING . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again Refer to APIM HARDWARE TESTING . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, Refer to APIM HARDWARE TESTING . |
| U3000:88 | Control Module: Bus Off |
NOTE:
Network communication/message Diagnostic Trouble Codes (DTCs) can result from intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often set these Diagnostic Trouble Codes (DTCs). Replacing a module to resolve a network DTC is unlikely to resolve the concern. The module was unable to communicate on the network at a point in time. The fault is not currently present. To avoid repeat network concerns: INSPECT for damaged or corroded wiring at the APIM.TEST the vehicle battery. REFER to: Battery
.CLEAR the DTC.REPEAT the network test with the diagnostic scan tool. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AW |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AX |