ABS Module
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B10DF:46 | Master Cylinder Isolation Valve: Calibration / Parameter Memory Failure | This DTC sets due to an internal failure of the ABS module or a calibration failure between the HCU and the ABS module. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration and then the Master Cylinder Isolation Calibration. CLEAR the DTC and REPEAT the self-test. If the DTC returns, REPEAT the 2 calibration routines making sure to FOLLOW the diagnostic scan tool directions. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| B1111:44 | Electric Park Brake Enable: Data Memory Failure | REFER to: Parking Brake . |
| B1111:46 | Electric Park Brake Enable: Calibration / Parameter Memory Failure | REFER to: Parking Brake . |
| B1111:49 | Electric Park Brake Enable: Internal Electronic Failure | REFER to: Parking Brake . |
| B1111:4B | Electric Park Brake Enable: Over Temperature | REFER to: Parking Brake . |
| B1111:53 | Electric Park Brake Enable: Deactivated | REFER to: Parking Brake . |
| B1111:54 | Electric Park Brake Enable: Missing Calibration | REFER to: Parking Brake . |
| C0001:01 | TCS Control Channel "A" Valve 1: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0002:01 | TCS Control Channel "A" Valve 2: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0003:01 | TCS Control Channel "B" Valve 1: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0004:01 | TCS Control Channel "B" Valve 2: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0010:01 | Left Front Inlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0011:01 | Left Front Outlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0014:01 | Right Front Inlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0015:01 | Right Front Outlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0018:01 | Left Rear Inlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0019:01 | Left Rear Outlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C001C:01 | Right Rear Inlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C001D:01 | Right Rear Outlet Control: General Electrical Failure | This DTC indicates part of the ABS module has failed internally. CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0020:11 | ABS Pump Motor Control: Circuit Short To Ground | GO to Pinpoint Test H |
| C0020:12 | ABS Pump Motor Control: Circuit Short To Battery | GO to Pinpoint Test H |
| C0020:13 | ABS Pump Motor Control: Circuit Open | GO to Pinpoint Test H |
| C0020:71 | ABS Pump Motor Control: Actuator Stuck | GO to Pinpoint Test H |
| C0030:07 | Left Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0031:07 | Left Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0031:11 | Left Front Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test K |
| C0031:15 | Left Front Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test K |
| C0031:29 | Left Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0031:4A | Left Front Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any
"Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Front Wheel Speed Sensor . |
| C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0033:07 | Right Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0034:07 | Right Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0034:11 | Right Front Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test K |
| C0034:15 | Right Front Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test K |
| C0034:29 | Right Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0034:4A | Right Front Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing any
"Incorrect Component Installed" wheel speed sensor Diagnostic Trouble Codes (DTCs). This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Front Wheel Speed Sensor . |
| C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0036:07 | Left Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C0037:07 | Left Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C0037:11 | Left Rear Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test L |
| C0037:15 | Left Rear Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test L |
| C0037:29 | Left Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C0037:4A | Left Rear Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE DTC U2100:00 and all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing DTC C0037:4A. This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Rear Wheel Speed Sensor . |
| C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0039:07 | Right Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test B |
| C003A:07 | Right Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test B |
| C003A:11 | Right Rear Wheel Speed Sensor: Circuit Short to Ground | GO to Pinpoint Test L |
| C003A:15 | Right Rear Wheel Speed Sensor: Circuit Short to Battery or Open | GO to Pinpoint Test L |
| C003A:29 | Right Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test B |
| C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test B |
| C003A:4A | Right Rear Wheel Speed Sensor: Incorrect Component Installed | DIAGNOSE DTC U2100:00 and all other wheel speed sensor Diagnostic Trouble Codes (DTCs) before diagnosing DTC C0037:4A. This DTC sets when the incorrect type of wheel speed sensor has been installed, bi-directional versus non-bi-directional. For information on wheel speed sensor types, REFER to: Anti-Lock Brake System (ABS) and Stability Control - System Operation and Component Description . INSTALL a new wheel speed sensor. REFER to: Rear Wheel Speed Sensor . |
| C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test B |
| C0040:64 | Brake Pedal Switch "A": Signal Plausibility Failure | GO to Pinpoint Test C |
| C0044:28 | Brake Pressure Sensor "A": Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test C |
| C0044:47 | Brake Pressure Sensor "A": Watchdog / Safety Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:47 returns, VERIFY all ABS module-to- HCU fasteners are tightened to specifications. If all fasteners are tightened to their correct specifications, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0044:49 | Brake Pressure Sensor "A": Internal Electronic Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:49 returns, VERIFY all ABS module-to- HCU fasteners are tightened to specifications. If all fasteners are tightened to their correct specifications, INSTALL a new ABS module and HCU assembly. REFER to: Hydraulic Control Unit (HCU) . |
| C0044:51 | Brake Pressure Sensor "A": Not Programmed | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:51 returns, VERIFY all ABS module-to- HCU fasteners are tightened to specifications. If all fasteners are tightened to their correct specifications, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0044:64 | Brake Pressure Sensor "A": Signal Plausibility Failure | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:64 returns, VERIFY all ABS module-to- HCU fasteners are tightened to specifications. If all fasteners are tightened to their correct specifications, INSPECT the brake tubes and connections for damage and leaks. REPAIR or INSTALL new brake tubes as necessary. If the brake tubes and connections are OK and there are no brake fluid leaks, BLEED the brake system. REFER to: Brake System Pressure Bleeding . CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the ABS module self-test. If this DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0044:8F | Brake Pressure Sensor "A": Erratic | DIAGNOSE DTC C0040:64 before diagnosing this DTC. If DTC C0040:64 is not present, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. REPEAT the self-test. If DTC C0044:8F returns, VERIFY all ABS module-to- HCU fasteners are tightened to specifications. If all fasteners are tightened to their correct specifications, INSTALL a new ABS module and HCU assembly. REFER to: Hydraulic Control Unit (HCU) . |
| C0047:01 | Brake Booster Pressure Sensor: General Electric Failure | GO to Pinpoint Test M |
| C0047:1B | Brake Booster Pressure Sensor: Circuit Resistance Above Threshold | GO to Pinpoint Test M |
| C0047:26 | Brake Booster Pressure Sensor: Signal Rate of Change Below Threshold | GO to Pinpoint Test M |
| C0047:27 | Brake Booster Pressure Sensor: Signal Rate of Change Above Threshold | GO to Pinpoint Test M |
| C0051:28 | Steering Wheel Position Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test J |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test J |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test J |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test J |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test J |
| C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0061:2F | Lateral Acceleration Sensor: Signal Erratic | GO to Pinpoint Test G |
| C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0062:28 | Longitudinal Acceleration Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | This DTC sets if the stability sensors in the RCM have not been calibrated or the calibration has been lost. CARRY OUT the IVD Initialization routine, FOLLOW the diagnostic scan tool instructions. If the module fails the initialization routine, VERIFY the RCM is installed correctly and the fasteners are tightened to specifications. REINSTALL the RCM or INSTALL a new RCM as necessary. REFER to: Restraints Control Module (RCM) . If the RCM is OK, CARRY OUT the RCM self-test. RETRIEVE and RECORD any Diagnostic Trouble Codes (DTCs). REFER to: Airbag and Seatbelt Pretensioner Supplemental Restraint System (SRS) - System Operation and Component Description . If the module passes the calibration routine, CLEAR the DTC. CYCLE the ignition from ON to OFF and back to ON. CARRY OUT the ABS module self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0062:76 | Longitudinal Acceleration Sensor: Wrong Mounting Position | Due to the nature of the longitudinal acceleration sensor, the RCM must be installed in the correct orientation to the centerline of the vehicle. This DTC sets if the RCM has been installed in the wrong position. VERIFY the RCM is installed correctly and the fasteners are tightened to specifications. REINSTALL the RCM or INSTALL a new RCM as necessary. REFER to: Restraints Control Module (RCM) . If the RCM is OK, CARRY OUT the RCM self-test. RETRIEVE and RECORD any Diagnostic Trouble Codes (DTCs). REFER to: Airbag and Seatbelt Pretensioner Supplemental Restraint System (SRS) - System Operation and Component Description . |
| C0063:28 | Yaw Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0063:2F | Yaw Rate Sensor: Signal Erratic | GO to Pinpoint Test G |
| C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C0064:28 | Roll Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure | GO to Pinpoint Test G |
| C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test G |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | DIAGNOSE all other ABS module Diagnostic Trouble Codes (DTCs) before diagnosing DTC C006B:00 If no other ABS module Diagnostic Trouble Codes (DTCs) are present, GO to Pinpoint Test O |
| C0072:68 | Brake Temperature Too High: Event Information | This DTC is set due to HS-CAN concerns, CCM concerns or a hard reset of the ABS module (battery disconnected or ignition ON with ABS module electrical connector disconnected). When this DTC is set, the ABS module disables adaptive cruise control until the temperature is returned to normal. The DTC does not illuminate any warning indicators but the message center displays ADAPTIVE CRUISE CONTROL NOT AVAILABLE. RETRIEVE and DIAGNOSE all CAN Diagnostic Trouble Codes (DTCs) in the ABS module and the CCM. REFER to DTC Chart: ABS Module or REFER to: Cruise Control . If there are no CAN Diagnostic Trouble Codes (DTCs) present, RETRIEVE and DIAGNOSE all CCM Diagnostic Trouble Codes (DTCs) other than C0072:00. REFER to: Cruise Control . If DTC C0072:00 is the only DTC present in the CCM or ABS module, ALLOW the vehicle to cool down for 30 minutes. CLEAR all ABS module Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the ABS module DTC returns, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) . |
| C1015:08 | Vacuum Supply: Bus Signal / Message Failure | GO to Pinpoint Test R |
| C1015:7A | Vacuum Supply: Fluid Leak or Seal Failure | GO to Pinpoint Test R |
| C1015:7B | Vacuum Supply: Low Fluid Level | GO to Pinpoint Test R |
| C1020:00 | Brake System Fill Not Complete: No Sub-Type Information | This DTC is pre-set in a new ABS module and can only be cleared when the Brake System Service Bleed is successfully carried out. CARRY OUT the Brake System Service Bleed. REFER to: Brake System . |
| C1034:71 | Parking Brake: Actuator Stuck | REFER to: Parking Brake . |
| C1137:29 | Reverse Gear Switch: Signal Invalid | This DTC sets when the ABS module receives an "invalid" message from the PCM instead of the actual current transmission gear. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM. 2.0L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 2.7L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 3.5L Duratec REFER to: ELECTRONIC ENGINE CONTROLS . |
| C1137:64 | Reverse Gear Switch: Signal Plausibility Failure | This DTC sets when the reverse gear message sent from the PCM indicates the transmission is in REVERSE when other stability control inputs received by the ABS module indicate the vehicle is moving forward. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM. 2.0L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 2.7L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 3.5L Duratec REFER to: ELECTRONIC ENGINE CONTROLS . |
| C1A08:1C | Pressure Sensor Supply: Circuit Voltage Out of Range | The brake system pressure sensor is supplied voltage by the ABS module. The ABS module monitors this output and sets this DTC when the voltage is out of range. DIAGNOSE DTC U3003:16 or U3003:17, before diagnosing C1A08:1C. If DTC U3003:16 or U3003:17 is not present, make sure all ABS module-to- HCU fasteners are tightened to their correct torque specifications. If all fasteners are tightened to their correct torque specifications, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| C1A43:91 | Motor Supply: Parametric | REFER to: Parking Brake . |
| C1A43:98 | Motor Supply: Component or System Over Temperature | REFER to: Parking Brake . |
| C1B14:11 | Sensor Supply Voltage "A": Circuit Short to Ground | GO to Pinpoint Test M |
| C1B14:12 | Sensor Supply Voltage "A": Circuit Short to Battery | GO to Pinpoint Test M |
| C1B15:1C | Sensor Supply Voltage "B": Circuit Voltage Out of Range | GO to Pinpoint Test M |
| C2005:1B | Right Actuator: Circuit Resistance Above Threshold | REFER to: Parking Brake . |
| C2005:71 | Right Actuator: Actuator Stuck | REFER to: Parking Brake . |
| C2005:74 | Right Actuator: Actuator Slipping | REFER to: Parking Brake . |
| C2005:77 | Right Actuator: Commanded Position Not Reachable | REFER to: Parking Brake . |
| C2005:92 | Right Actuator: Performance or Incorrect Operation | REFER to: Parking Brake . |
| C2006:1B | Left Actuator: Circuit Resistance Above Threshold | REFER to: Parking Brake . |
| C2006:71 | Left Actuator: Actuator Stuck | REFER to: Parking Brake . |
| C2006:74 | Left Actuator: Actuator Slipping | REFER to: Parking Brake . |
| C2006:77 | Left Actuator: Commanded Position Not Reachable | REFER to: Parking Brake . |
| C2006:92 | Left Actuator: Performance or Incorrect Operation | REFER to: Parking Brake . |
| C2007:13 | Right Motor: Circuit Open | REFER to: Parking Brake . |
| C2007:1C | Right Motor: Circuit Voltage Out of Range | REFER to: Parking Brake . |
| C2007:92 | Right Motor: Performance or Incorrect Operation | REFER to: Parking Brake . |
| C2007:96 | Right Motor: Component Internal Failure | REFER to: Parking Brake . |
| C2008:13 | Left Motor: Circuit Open | REFER to: Parking Brake . |
| C2008:1C | Left Motor: Circuit Voltage Out of Range | REFER to: Parking Brake . |
| C2008:92 | Left Motor: Performance or Incorrect Operation | REFER to: Parking Brake . |
| C2008:96 | Left Motor: Component Internal Failure | REFER to: Parking Brake . |
| P0942:46 | Hydraulic Pressure Unit: Calibration / Parameter Memory Failure | The ABS module and HCU should not be swapped between different vehicles. This DTC sets when the identification data stored in the ABS module does not match the identification data from the HCU. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine and then the Master Cylinder Isolation Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module and HCU assembly. REFER to: Hydraulic Control Unit (HCU) . |
| P0942:49 | Hydraulic Pressure Unit: Internal Electronic Failure | The ABS module and HCU should not be swapped between different vehicles. This DTC sets when the identification data stored in the ABS module does not match the identification data from the HCU. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine and then the Master Cylinder Isolation Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module and HCU assembly. REFER to: Hydraulic Control Unit (HCU) . |
| P193B:86 | Throttle / Pedal Signal: Signal Invalid | This DTC sets when the accelerator pedal position message sent from the PCM is "invalid" instead of the actual pedal position. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM. 2.0L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 2.7L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 3.5L Duratec REFER to: ELECTRONIC ENGINE CONTROLS . |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. DIAGNOSE no HS-CAN communication, all modules are not responding. REFER to: Communications Network . |
| U0100:00 | Lost Communication With ECM / PCM "A": No Sub Type Information | GO to Pinpoint Test I |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U0126:87 | Lost Communication With Steering Angle Sensor Module: Missing Message | GO to Pinpoint Test S |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test Q |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test T |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test T |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test U |
| U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | CHECK vehicle service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper flash programming procedures. If there have been recent service actions with the ABS module, REPEAT the programming procedure as directed by the diagnostic scan tool. |
| U0401:00 | Invalid Data Received From ECM / PCM "A": No Sub Type Information | This DTC sets if the ABS module receives invalid data in any of the following messages; brake pedal position, gear lever position or driven wheel torque. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PCM and GWM Diagnostic Trouble Codes (DTCs). REFER to: Communications Network . 2.0L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 2.7L EcoBoost REFER to: ELECTRONIC ENGINE CONTROLS . 3.5L Duratec REFER to: ELECTRONIC ENGINE CONTROLS . If the diagnostic scan tool cannot communicate with the PCM or GWM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the PCM or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0405:41 | Invalid Data Received From Cruise Control Module: General Checksum Failure | This DTC sets if the collision mitigation by braking deceleration message checksum is invalid. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all CCM Diagnostic Trouble Codes (DTCs). REFER to: Cruise Control . If the diagnostic scan tool cannot communicate with the CCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the CCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0405:82 | Invalid Data Received From Cruise Control Module: Alive / Sequence Counter Incorrect / Not Updated | This DTC sets if the collision mitigation by braking deceleration message rolling counter is invalid. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all CCM Diagnostic Trouble Codes (DTCs). REFER to: Cruise Control . If the diagnostic scan tool cannot communicate with the CCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the CCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0405:86 | Invalid Data Received From Cruise Control Module: Signal Invalid | This DTC sets if the CCM is requesting an external apply of the EPB and the vehicle is not in static mode. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all CCM Diagnostic Trouble Codes (DTCs). REFER to: Cruise Control . If the diagnostic scan tool cannot communicate with the CCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the CCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0420:00 | Invalid Data Received From Power Steering Control Module: No Sub Type Information | This DTC sets if the ABS module receives invalid steering wheel torque information. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PSCM Diagnostic Trouble Codes (DTCs). REFER to: Power Steering . If the diagnostic scan tool cannot communicate with the PSCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the PSCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PSCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0420:41 | Invalid Data Received From Power Steering Control Module: General Checksum Failure | This DTC sets if the steering wheel angle sensor checksum is invalid. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PSCM Diagnostic Trouble Codes (DTCs). REFER to: Power Steering . If the diagnostic scan tool cannot communicate with the PSCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the PSCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PSCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0420:82 | Invalid Data Received From Power Steering Control Module: Alive / Sequence Counter Incorrect / Not Updated | This DTC sets if the steering wheel angle sensor message rolling counter is out or range. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PSCM Diagnostic Trouble Codes (DTCs). REFER to: Power Steering . If the diagnostic scan tool cannot communicate with the PSCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the PSCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PSCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0420:86 | Invalid Data Received From Power Steering Control Module: Signal Invalid | This DTC sets if the information in the steering wheel angle sensor message is out or range or invalid. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all PSCM Diagnostic Trouble Codes (DTCs). REFER to: Power Steering . If the diagnostic scan tool cannot communicate with the PSCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the PSCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all PSCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets if the ignition switch status message is invalid. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all BCM and GWM Diagnostic Trouble Codes (DTCs). REFER to: Communications Network . REFER to: Body Control Module (BCM) . If the diagnostic scan tool cannot communicate with the BCM or GWM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the BCM or GWM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all BCM and GWM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0428:81 | Invalid Data Received From Steering Angle Sensor Module: Invalid Serial Data Received | This DTC sets if the ABS module receives "no data exists" or "faulty" in the active steering messages. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SASM Diagnostic Trouble Codes (DTCs). REFER to: Steering Wheel and Column Electrical Components . If the diagnostic scan tool cannot communicate with the SASM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the SASM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SASM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0428:82 | Invalid Data Received From Steering Angle Sensor Module: Alive / Sequence Counter Incorrect / Not Updated | This DTC sets if the active steering rolling counter is incorrect. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SASM Diagnostic Trouble Codes (DTCs). REFER to: Steering Wheel and Column Electrical Components . If the diagnostic scan tool cannot communicate with the SASM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the SASM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SASM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0428:83 | Invalid Data Received From Steering Angle Sensor Module: Value of Signal Protection Calculation Incorrect | This DTC sets if the calculated and the received active steering checksum is incorrect. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all SASM Diagnostic Trouble Codes (DTCs). REFER to: Steering Wheel and Column Electrical Components . If the diagnostic scan tool cannot communicate with the SASM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the SASM, the DTC may be caused by an intermittent concern. SET the ignition to OFF. DISCONNECT and INSPECT all SASM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0452:29 | Invalid Data Received From Restraints Control Module: Signal Invalid | This DTC sets if the ABS module receives a faulty driver seat belt buckle status and the driver is attempting a EPB drive away release. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . If the diagnostic scan tool cannot communicate with the RCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the RCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF and WAIT one minute. DISCONNECT and INSPECT all RCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0452:41 | Invalid Data Received From Restraints Control Module: General Checksum Failure | This DTC sets if the check sum in the stability sensor messages is invalid or does not match the ABS module calculated check sum more than twice. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . If the diagnostic scan tool cannot communicate with the RCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the RCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF and WAIT one minute. DISCONNECT and INSPECT all RCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | This DTC sets if any of the stability sensors messages (yaw rate, roll rate, lateral acceleration or longitudinal acceleration) is invalid or out of range. Using a diagnostic scan tool, RETRIEVE and DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . If the diagnostic scan tool cannot communicate with the RCM, REFER to: Communications Network . If there are no Diagnostic Trouble Codes (DTCs) in the RCM, the DTC may be caused by an intermittent concern. SET the ignition to OFF and WAIT one minute. DISCONNECT and INSPECT all RCM electrical connectors and related in-line connectors for corrosion, bent pins, pushed-out pins and spread terminals. REPAIR as necessary. |
| U2002:47 | Switch: Watchdog / Safety Failure | REFER to: Parking Brake . |
| U2002:96 | Switch: Component Internal Failure | REFER to: Parking Brake . |
| U2007:46 | Valve(s): Calibration / Parameter Memory Failure | This DTC sets due to an internal failure of the ABS module or due to a calibration failure between the HCU and the ABS module. Using a diagnostic scan tool, CARRY OUT the Inlet Valve Calibration routine and then the Master Cylinder Isolation Calibration routine. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2007:62 | Valve(s): Signal Compare Failure | This DTC sets due to an internal failure of the ABS module or due to a calibration failure between the HCU and the ABS module. CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | This DTC is only present when a new ABS module is installed, the ABS module is flashed or the ABS module is reconfigured. Using a diagnostic scan tool, CONFIGURE the ABS module, FOLLOW all diagnostic scan tool instructions. Using a diagnostic scan tool, CARRY OUT the ABS module self-test to clear the DTC. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC is pre-set in a new ABS module and clears automatically when the ABS module is configured correctly. CHECK the service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with the ABS module, REPEAT the PMI procedure, FOLLOW all diagnostic scan tool instructions. CARRY OUT the IVD Initialization procedure, FOLLOW all diagnostic scan tool directions. If there have been no recent service actions, INSTALL a new ABS module to correct the failure to retain the configuration data. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with the ABS module, REPEAT the PMI procedure, FOLLOW all diagnostic scan tool instructions. CARRY OUT the IVD Initialization procedure, FOLLOW all diagnostic scan tool directions. If there have been no recent service actions, INSTALL a new ABS module to correct the failure to retain configuration data. REFER to: Anti-Lock Brake System (ABS) Module . |
| U2107:00 | Collision Mitigation By Braking: No Sub Type Information | This DTC sets when the collision deceleration message from the CCM is sent too often or the duration of the message is too long. This is most likely caused by a network communication concern or an internal failure of the CCM. RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the CCM. REFER to: Cruise Control . |
| U2107:68 | Collision Mitigation By Braking: Event Information | This DTC sets when the vehicle deceleration detected is implausibly high when compared to the vehicle deceleration requested by the CCM. This is most likely caused by an abrupt stop of the vehicle due to a collision, an extreme driving situation, a mechanical or electrical failure of the cruise control system or an internal failure of the ABS module. RETRIEVE and REPAIR all other ABS module Diagnostic Trouble Codes (DTCs) before diagnosing DTC U2107:68. If there are no other ABS module Diagnostic Trouble Codes (DTCs) present, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the CCM. REFER to: Cruise Control . If there are no Diagnostic Trouble Codes (DTCs) in the CCM, INSPECT the vehicle braking system for a dragging condition or another condition that may cause rapid vehicle deceleration. |
| U2108:00 | Adaptive Cruise Control: No Sub Type Information | In order to detect errors in the CCM, the cruise control system is momentarily shut off during a driver braking event. This DTC sets when the ABS module detects cruise control system activation during a driver braking event. This is most likely caused by a network communication concern or an internal failure of the CCM. RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the CCM. REFER to: Cruise Control . |
| U2108:68 | Adaptive Cruise Control: Event Information | The ABS module monitors vehicle deceleration during adaptive cruise control braking events to prevent an over-braking situation. This DTC sets when vehicle deceleration is greater than 3.2 meters per second_2. This is most likely caused by an abrupt stop of the vehicle due to a collision, an extreme driving situation, a mechanical or electrical failure of the adaptive cruise control system or an internal failure of the ABS module. RETRIEVE and REPAIR all other ABS module Diagnostic Trouble Codes (DTCs) before diagnosing DTC U2108:68. If there are no other ABS module Diagnostic Trouble Codes (DTCs) present, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the CCM. REFER to: Cruise Control . If there are no Diagnostic Trouble Codes (DTCs) in the CCM, INSPECT the vehicle braking system for a dragging condition or another condition that may cause rapid vehicle deceleration. |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CHECK the service history for recent service actions related to the ABS module. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with the ABS module, REPEAT the PMI procedure, FOLLOW all diagnostic scan tool instructions. CARRY OUT the IVD Initialization procedure, FOLLOW all diagnostic scan tool directions. If there have been no recent service actions, INSTALL a new ABS module to correct the failure to retain configuration data. REFER to: Anti-Lock Brake System (ABS) Module . |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the Diagnostic Trouble Codes (DTCs). CARRY OUT the ABS module self-test. RETRIEVE and RECORD all Diagnostic Trouble Codes (DTCs). If the DTC returns INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U3000:96 | Control Module: Component Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). CARRY OUT the ABS module self-test. RETRIEVE and RECORD all Diagnostic Trouble Codes (DTCs). If the DTC returns INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) Module . |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test N |
| U3003:08 | Battery Voltage: Bus Signal / Message Failure | This DTC sets when the HS-CAN is shorted together, shorted to ground, shorted to voltage or open. If DTC U3003:16 is present, DIAGNOSE DTC U3003:16 before diagnosing DTC U3003:08. If DTC U3003:16 is not present, REFER to: Communications Network . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| U3003:1C | Battery Voltage: Circuit Voltage Out of Range | GO to Pinpoint Test A |
| U300A:29 | Ignition Switch: Signal Invalid | If ABS module DTC U0001:88, U0140:00 or U0422:00 is present, DIAGNOSE that DTC before diagnosing DTC U300A:29. If ABS module DTC U0001:88, U0140:00 or U0422:00 is not present, GO to Pinpoint Test A |