Automatic Transmission DTCS: 6F35
DTC INDEX
| DTC | Description | Component | Action |
|---|---|---|---|
| P0604 | Internal Control Module RAM Error | TCM | REPROGRAM the TCM to the latest calibration. CLEAR the DTC. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM the TCM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | TCM | REPROGRAM the TCM to the latest calibration. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM the TCM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P0607 | Control Module Performance | TCM | REPROGRAM the TCM to the latest calibration. CLEAR the DTC. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM the TCM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P0657 | Actuator Supply Voltage "A" Circuit/Open | Solenoid power control | Power to all solenoids has been interrupted, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F . |
| P06B8 | Internal Control Module NVRAM Error | TCM | REPROGRAM the TCM to the latest calibration. CLEAR the DTC. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM the TCM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)). | DTCs P2700, P2701, P2702, P2703 and/or P2704 may set. CLEAR the DTCs. If the DTC returns, GO to Symptom Chart . |
| P0702 | Transmission Control System Electrical | Low or high system voltage | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to Charging System Symptom Chart. |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | TR sensor | This DTC sets when the duty cycle is greater or less than the expected duty cycle by Hz or more. Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0707 | Transmission Range Sensor "A" Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0708 | Transmission Range Sensor "A" Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0709 | TR Sensor A Circuit Intermittent | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | TFT | DTCs P0712 or P0713 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | TFT | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | TFT | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | TFT | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0715 | Turbine/Input Shaft Speed Sensor "A" Circuit | TSS sensor | DTC P0717 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . REPAIR the more specific DTC first. |
| P0717 | Turbine/Input Shaft Speed Sensor "A" Circuit No Signal | TSS sensor | DTC P0715 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . REPAIR the more specific DTC first. |
| P0718 | Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent | TSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . |
| P0720 | Output Shaft Speed Sensor Circuit | OSS sensor | DTC P0722 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . REPAIR the more specific DTC first. |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | OSS sensor | DTC P0720 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . REPAIR the more specific DTC first. |
| P0729 | Gear 6 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 5-6 shift/harsh/soft/slipping. |
| P0731 | Gear 1 Incorrect Ratio | Forward Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0732 | Gear 2 Incorrect Ratio | Forward Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0733 | Gear 3 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0734 | Gear 4 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0735 | Gear 5 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 4-5 shift/harsh/soft/slipping. |
| P073D | Unable to Engage Neutral | Transmission forward or direct clutch packs | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Transmission - Overhaul . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | TCC Solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0742 | Torque Converter Clutch Solenoid Circuit Stuck On | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | TCC Solenoid electrical faults | DTCs P0740, P0742 and/or P0744 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . REPAIR the more specific DTC first. |
| P0744 | Torque Converter Clutch Solenoid Circuit Intermittent | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . REPAIR the more specific DTC first. |
| P0748 | Pressure Control Solenoid "A" Electrical | Line pressure control (LPC) Solenoid electrical faults | DTCs P0960, P0962 and/or P0963 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0750 | Shift Solenoid "A" | Shift Solenoid A (SSA) electrical faults | DTC P0751 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | DTC P2700 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no forward. |
| P0752 | Shift Solenoid "A" Stuck On | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 1, 2, 3, 4 available. |
| P0753 | Shift Solenoid "A" Electrical | SSA electrical faults | DTCs P0750, P0973 and/or P0974 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0754 | Shift Solenoid "A" Intermittent | SSA electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . |
| P0755 | Shift Solenoid "B" | SSB electrical faults | DTC P0756 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | SSB electrical faults | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 3 and 5 available. |
| P0757 | Shift Solenoid "B" Stuck On | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) SSB electrical faults, SSB electrical faults | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0758 | Shift Solenoid "B" Electrical | SSB electrical faults | DTCs P0755, P0976 and/or P0977 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0759 | Shift Solenoid "B" Intermittent | SSB electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . |
| P0760 | Shift Solenoid "C" | Shift solenoid C (SSC) electrical faults | DTC P0761 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P2702 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0762 | Shift Solenoid "C" Stuck On | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 2 and 6 available. |
| P0763 | Shift Solenoid "C" Electrical | SSC electrical faults | DTCs P0760, P0979 and/or P0980 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0764 | Shift Solenoid "C" Intermittent | SSC electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . |
| P0765 | Shift Solenoid "D" | SSD electrical faults | DTC P0766 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | SSD electrical faults | DTC P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P0767 | Shift Solenoid "D" Stuck On | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTCs P07A9 and/or P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0768 | Shift Solenoid "D" Electrical | SSD electrical faults | DTCs P0765, P0982 and/or P0983 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0769 | Shift Solenoid "D" Intermittent | SSD electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . |
| P0770 | Shift Solenoid "E" | Shift Solenoid E (SSE) electrical faults | DTC P0773 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . REPAIR the more specific DTC first. |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | SSE Non- electrical faults (SSE and main control valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns. |
| P0772 | Shift Solenoid "E" Stuck On | SSE Non- electrical faults (SSE and valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0773 | Shift Solenoid "E" Electrical | SSE electrical faults | DTC P0770 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . REPAIR the more specific DTC first. |
| P0774 | Shift Solenoid "E" Intermittent | SSE electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . |
| P07A5 | Transmission Friction Element "B" Stuck On | Direct clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P07A8 | Transmission Friction Element "D" Performance/Stuck Off | Low/reverse clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P07A9 | Transmission Friction Element "D" Stuck On | Low/reverse clutch | DTC P0767 may set, CLEAR the DTC. TEST the symptom for normal operation. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P07AA | Transmission Friction Element "E" Performance/Stuck Off | Overdrive clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns. |
| P0815 | Upshift Switch Circuit | Upshift switch electrical | For Tow Haul and Grade Assist, REFER to Automatic Transaxle Transmission External Controls Transmission Control Switch (TCS) . For Select Shift™, REFER to Automatic Transaxle Transmission External Controls Select Shift . For Low Gear Select, REFER to Automatic Transaxle-Transmission External Controls Column Shift . |
| P0816 | Downshift Switch Circuit | Downshift switch electrical | For Tow Haul and Grade Assist, REFER to Automatic Transaxle Transmission External Controls Transmission Control Switch (TCS) . For Select Shift™, REFER to Automatic Transaxle Transmission External Controls Select Shift . For Low Gear Select, REFER to Automatic Transaxle-Transmission External Controls Column Shift . |
| P0867 | Transmission Fluid Pressure | Transmission hydraulic and clutch systems | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0882 | TCM Power Input Signal Low | TCM power input signal low | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to Charging System System Chart. |
| P0883 | TCM Power Input Signal High | TCM power input signal high | CLEAR the DTC. TEST the system for normal operation. If the DTC returns, REFER to Charging System System Chart. |
| P0884 | TCM Power Input Signal Intermittent | TCM power input signal | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to Charging System System Chart. |
| P0960 | Pressure Control Solenoid "A" Control Circuit/Open | Line Pressure Control (LPC) solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0961 | Pressure Control Solenoid "A" Control Circuit Range/Performance | LPC solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . |
| P0962 | Pressure Control Solenoid "A" Control Circuit Low | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0963 | Pressure Control Solenoid "A" Control Circuit High | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0973 | Shift Solenoid "A" Control Circuit Low | SSA electrical faults | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0974 | Shift Solenoid "A" Control Circuit High | SSA electrical faults | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0976 | Shift Solenoid "B" Control Circuit Low | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0977 | Shift Solenoid "B" Control Circuit High | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0979 | Shift Solenoid "C" Control Circuit Low | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0980 | Shift Solenoid "C" Control Circuit High | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
DTC INDEX
| P0982 | Shift Solenoid "D" Control Circuit Low | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
|---|---|---|---|
| P0983 | Shift Solenoid "D" Control Circuit High | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0984 | Shift Solenoid "E" Control Circuit Range/Performance | SSE electrical faults | DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns. |
| P1001 | KOER Not Able to Complete, KOER Aborted | PCM | READ and RECORD all DTCs. REPAIR any self-test or continuous DTCs first. CLEAR the DTC. PERFORM the KOER self-test. If the DTC returns, REPROGRAM the TCM to the latest calibration. PERFORM the KOER self-test. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P1397 | System Voltage Out Of Self Test Range | System voltage out of self test range | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed out terminals, corrosion or loose wires. CLEAR the DTC. PERFORM the KOEO and KOER self-test. If the DTC returns, REFER to Charging System System Chart. |
| P1501 | Vehicle Speed Sensor Out Of Self Test Range | VSS | CLEAR the DTC. If the DTC returns, PLACE selector lever in park and monitor the VSS PID. VERIFY the VSS input is at 0. PERFORM the KOER self-test. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control . |
| P1635 | Tire/Axle Out of Acceptable Range | ABS | CLEAR the DTC. If the DTC returns, REFER to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing the new TCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P163E | Transmission Control Module Programming Error | TCM programming error | CLEAR the DTC. If the DTC returns, REPROGRAM the TCM to the latest calibration. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing a new TCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P163F | Transmission ID Block Corrupted, Not Programmed | Transmission id memory block corrupted, not programmed | CLEAR the DTC. If the DTC returns, REPROGRAM the TCM to the latest calibration. If the DTC returns, INSTALL a new TCM. REFER to Transmission Control Module (TCM) . After installing a new TCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . |
| P1702 | Transmission Range Sensor Circuit Intermittent | TR sensor electrical faults | DTCs P0706, P0707 and/or P0708 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . REPAIR the more specific DTC first. |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test | TR sensor | CLEAR the DTC. PERFORM the KOEO and KOER self-test. |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self Test Range | TFT | CLEAR the DTC. PERFORM the KOEO and KOER self-test. |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | TCC System Faults (includes TCC, main control valve body and non-electrical solenoid faults) | DTC P1744 is a non-electrical DTC. CLEAR the DTC. ROAD TEST the vehicle. If the DTCs returns, GO to Symptom Chart for torque converter operation concerns/no apply. |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out Of Self Test Range | Transmission control switch | REFER to Automatic Transaxle-Transmission External Controls Column Shift . |
| P1783 | Transmission Over Temperature Condition | Transmission over temperature | MONITOR the TFT sensor PID and TCC PID to VERIFY and MONITOR the transmission fluid temperature and TCC solenoid electrical operation. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P1910 | Reverse Lamp Control Circuit/Open | Reverse lamp control | CLEAR the DTC. If the DTC returns, REFER to Exterior Lighting . |
| P1921 | Transmission Range Signal | TR | Engine may not crank. DTCs P0706, P0707 and/or P0708 may set. CLEAR the DTC. If the DTC returns, REPAIR the more specific DTC first. GO to Pinpoint Test J . |
| P1934 | Vehicle Speed Signal | VSS | DTCs U0121, U0415 and/or P0720 may set. CLEAR the DTCs. If the DTC returns, REPAIR the more specific DTC first. |
DTC INDEX
| P193F | Vehicle Speed Signal Intermittent | VSS | CLEAR the DTC. If the DTC returns, PLACE selector lever in park and monitor the VSS PID. VERIFY the VSS input is at 0. PERFORM the KOER self-test. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control . |
|---|---|---|---|
| P2681 | Engine Coolant Bypass Valve "A" Control Circuit/Open | Engine coolant bypass valve | REFER to Transaxle Transmission Cooling . |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | DTC P2700 is a non-electrical DTC. DTCs P0751 and/or P0752 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns, no forward or delayed/soft forward and/or shift concerns/only gears 1, 2, 3, 4 available. |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) | DTC P2701 is a non-electrical DTC. DTCs P0756 and/or P0757 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 3 and 5 available. |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P2702 is a non-electrical DTC. DTCs P0761 and/or P0762 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or no 5-6 shift/harsh/soft/slipping or only gears 2 and 6 available. |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Low/reverse clutch and OWC faults | DTC P2703 is a non-electrical DTC. DTCs P0766 and/or P0768 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse. |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTC P2704 is a non-electrical DTC. DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | OWC faults | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, GO to Symptom Chart engagement concerns/neutral after launch. |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | TCC | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P2783 | Torque Converter Temperature Too High | TCC | TCC control valve stuck in the apply position. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for torque converter operation concerns/no apply. |
| U0028 | Vehicle Communication Bus "A" | Vehicle Communication Bus "A" | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0073 | Control Module Communication Bus "A" Off | Network Communication Bus "A" Off | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0100 | Lost Communication With ECM /PCM A | Lost Communication With ECM / PCM "A" | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0102 | Lost Communication with TCCM | Lost Communication With TCCM | CLEAR the DTC. RUN the Network Test. If the DTC returns, REFER to Module Communications Network . |
| U0115 | Lost Communication With ECM /PCM B | Lost Communication with ECM / PCM "B" | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0121 | Lost Communication With ABS Control Module | Lost Communication With ABS Control Module | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test N . |
| U0129 | Lost Communication With Brake System Control Module | Lost communication with brake system control module | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test N . |
| U0133 | Lost Communication With Active Roll Control Module | Lost communication with active roll control module | CLEAR the DTC. RUN the Network Test. If the DTC returns, REFER to Module Communications Network . |
| U0140 | Lost Communication With Body Control Module | Lost communication with BCM | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test O . |
| U0141 | Lost Communication With Body Control Module "A" | Lost communication with BCM "A" | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test O . |
| U0155 | Lost Communication With IPC Control Module | Lost communication with IPC Control Module | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test P . |
| U0294 | Lost Communication With IPC Control Module | Lost communication with IPC Control Module | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0401 | Invalid Data Received From ECM /PCM A | Invalid data received from ECM /PCM A | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test M . |
| U0415 | Invalid Data Received From ABS Control Module | Invalid data received from ABS control module | CLEAR the DTC. RUN the Network Test. If the DTC returns, GO to Pinpoint Test N . |