Rear View Mirror DTCS: IPM-A
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B11C7:46 | High Beam Sensor: Calibration/Parameter Memory Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new interior auto-dimming mirror to correct the failure to retain calibration or parameter data. Refer to Interior Rear View Mirror . |
| B11C7:97 | High Beam Sensor: Component or System Operation Obstructed or Blocked | Refer to article 'Exterior Lighting', Go to Pinpoint Test A . |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | GO to Pinpoint Test I . |
| B12D8:13 | Mirror Heater Output: Circuit Open | GO to Pinpoint Test I . |
| B13A6:14 | Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground Or Open | Refer to article 'Lane Departure Warning', Go to Pinpoint Test A . |
| C1001:78 | Vision System Camera: Alignment or Adjustment Incorrect | This DTC sets when a new IPM-A has been installed without performing the camera alignment. The camera alignment is initiated using the scan tool. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test J . |
| U0104:87 | Lost Communication With Cruise Control Module: Missing Message | GO to Pinpoint Test K . |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to Pinpoint Test L . |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test M . |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test N . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test O . |
| U0212:87 | Lost Communication with Steering Column Control Module: Missing Message | GO to Pinpoint Test P . |
| U0232:87 | Lost Communication With Side Obstacle Detection Control Module - Left: Missing Message | GO to Pinpoint Test Q . |
| U0233:87 | Lost Communication With Side Obstacle Detection Control Module - Right: Missing Message | GO to Pinpoint Test Q . |
| U0401:00 | Invalid Data Received from ECM/PCM "A": No Sub Type Information | This DTC can set due to a fault in the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to Electronic Engine Controls . |
| U0405:00 | Invalid Data Received from Cruise Control Module: No Sub Type Information | This DTC can set due to a fault in the C-CM. RETRIEVE and REPAIR all non-network DTCs in the C-CM and other modules on the network. REFER to Cruise Control Adaptive . |
| U0422:00 | Invalid Data Received from Body Control Module: No Sub Type Information | This DTC can set due to a fault in the BCM. RETRIEVE and REPAIR all non-network DTCs in the BCM and other modules on the network. REFER to Multifunction Electronic Modules . |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | This DTC can set due to a fault in the IPC. RETRIEVE and REPAIR all non-network DTCs in the IPC and other modules on the network. REFER to Instrumentation, Message Center, and Warning Chimes . |
| U0429:00 | Invalid Data Received from Steering Column Control Module: No Sub Type Information | This DTC can set due to a fault in the SCCM. RETRIEVE and REPAIR all non-network DTCs in the SCCM and other modules on network. REFER to Steering Column Switches . |
| U0452:00 | Invalid Data Received from Restraints Control Module: No Sub Type Information | This DTC can set due to a fault in the Restraints Control Module. RETRIEVE and REPAIR all non-network DTCs in the RCM and other modules on network. REFER to Supplemental Restraint System . |
| U1000:11 | Solid State Driver Protection Active - Driver Disabled: Circuit Short To Ground | The IPM-A has temporarily disabled the camera windshield defrost heater output due to excessive current draw caused by a short to ground. The output remains disabled until the cause of the excessive current draw is corrected. ADDRESS all other IPM-A DTCs first. After the cause of the concern has been corrected, CLEAR the IPM-A DTCs. |
| U201A:54 | Control Module Main Calibration Data: Missing Calibration | CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new interior auto-dimming mirror to correct the failure to retain calibration data. Refer to Interior Rear View Mirror . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new interior auto-dimming mirror to correct the failure to retain calibration data. Refer to Interior Rear View Mirror . |
| U2101:00 | Control Module Configuration: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new interior auto-dimming mirror to correct the failure to retain calibration data. Refer to Interior Rear View Mirror . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new interior auto-dimming mirror to correct the failure to retain calibration data. Refer to Interior Rear View Mirror . |
| U3000:42 | Control Module: General Memory Failure | INSTALL a new interior auto-dimming mirror. Refer to Interior Rear View Mirror . |
| U3000:49 | Control Module: Internal Electronic Failure | The IPM-A has permanently disabled the camera windshield defrost heater output due to excessive current draw caused by a short to ground. ADDRESS all other IPM-A DTCs first. After the cause of the concern has been corrected, INSTALL a new interior auto-dimming mirror. Refer to Interior Rear View Mirror . |
| U3000:93 | Control Module: No Operation | CLEAR the DTCs. PERFORM the IPM-A self test, if the DTC returns, INSTALL a new interior auto-dimming mirror. Refer to Interior Rear View Mirror . |
| U3000:96 | Control Module: Component Internal Failure | INSTALL a new interior auto-dimming mirror. Refer to Interior Rear View Mirror . |