3.2L DURATORQ-TDCI
DTC INDEX
| DTC | Description | Component | Action |
|---|---|---|---|
| P0218 | Transmission Fluid Temperature Sensor "A" Over Temperature Condition Engine | Transmission over temperature |
NOTE:
P0218 causes the powertrain to limit torque to prevent transmission overheating. The DTC P0218 may set in conjunction with DTC P1783. CLEAR the DTC. If DTC P0218 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwise, REFER to: Transmission Cooling
. |
| P0604 | Internal Control Module Random Access Memory (RAM) Error | TCM | REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. TEST the system for normal operation. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. Refer to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle . |
| P0605 | Internal Control Module Read Only Memory (ROM) Error | TCM | REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. TEST the system for normal operation. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. Refer to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle . |
| P0607 | Control Module Performance | TCM | REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. TEST the system for normal operation. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. Refer to: Transmission Strategy Download . Road test the vehicle and PERFORM the Adaptive Drive Cycle, REFER to: Adaptive Learning Drive Cycle . |
| P0657 | Actuator Supply Voltage A Circuit Open | TCM | Power is routed through the Transmission Solenoid Power Control (TSPC) relay (inside the TCM) to all solenoids. If the power circuit to the transmission solenoids or the TSPC relay fails open, then all solenoids are failed electrically off. CHECK for open, short to ground or the transmission connector disconnected. The TSPC relay also disables power to the transmission solenoids when certain transmission DTCs are set. REPAIR as required. CLEAR the DTC. GO to Pinpoint Test A |
| P06B8 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error | TCM | REPROGRAM the original TCM to the latest calibration. CLEAR the DTCs. TEST the system for normal operation. If DTCs return, INSTALL a new TCM. After installing the new TCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. Refer to: Transmission Strategy Download . Road test the vehicle, REFER to: Road Testing Vehicle . |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)). | Intermittent clutch on fault and may set with DTCs P2700, P2701, P2702, P2703 and/or P2704. CLEAR the DTC. If DTC P0701 returns, REFER to: Diagnosis By Symptom . |
| P0702 | Transmission Control System Electrical | Battery | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P0702 returns, REFER to: Charging System - 3.2L Duratorq-TDCi (148kW/200PS) - Puma . |
| P0705 | Transmission Range Sensor "A" Circuit (PRNDL Input) | TR sensor | GO to Pinpoint Test C |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank. CLEAR the DTC. If DTC P0706 returns, GO to Pinpoint Test C |
| P0707 | Transmission Range Sensor "A" Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If DTC P0707 returns, GO to Pinpoint Test C |
| P0708 | Transmission Range Sensor "A" Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If DTC P0708 returns, GO to Pinpoint Test C |
| P0709 | Transmission Range Sensor A Circuit Intermittent | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is within range but is in the dead band between the design position, and in-range but invalid duty cycle. GO to Pinpoint Test C |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | TFT sensor | CLEAR the DTC. If DTC P0710 returns, GO to Pinpoint Test B |
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | TFT sensor | CLEAR the DTC. If DTC P0711 returns, GO to Pinpoint Test B |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | TFT sensor | DTC P0710 may set. CLEAR the DTC. If DTC P0712 returns, GO to Pinpoint Test B |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | TFT sensor | DTC P0710 may set. CLEAR the DTC. If DTC P0713 returns, GO to Pinpoint Test B |
| P0715 | Turbine/Input Shaft Speed Sensor "A" Circuit | TSS sensor | DTC P0717 may set. CLEAR the DTC. If DTC P0715 returns, GO to Pinpoint Test D |
| P0717 | Turbine/Input Shaft Speed Sensor "A" Circuit No Signal | TSS sensor | This DTC sets when DTC P0715 is set. REFER to DTC P0715. |
| P0718 | Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent | TSS sensor | CLEAR the DTC. If DTC P0718 returns, GO to Pinpoint Test D |
| P0720 | Output Shaft Speed Sensor Circuit | OSS sensor | DTC P0722 may set. CLEAR the DTC. If DTC P0720 returns, GO to Pinpoint Test E |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If DTC P0721 returns, GO to Pinpoint Test E |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | OSS sensor | This DTC sets when DTC P0720 is set. REFER to DTC P0720. |
| P0729 | Gear 6 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0729 returns, REFER to: Diagnosis By Symptom . |
| P0731 | Gear 1 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0731 returns, REFER to: Diagnosis By Symptom . |
| P0732 | Gear 2 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0732 returns, REFER to: Diagnosis By Symptom . |
| P0733 | Gear 3 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0733 returns, REFER to: Diagnosis By Symptom . |
| P0734 | Gear 4 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0734 returns, REFER to: Diagnosis By Symptom . |
| P0735 | Gear 5 Incorrect Ratio | Transmission | CLEAR the DTC. If DTC P0735 returns, REFER to: Diagnosis By Symptom . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0740 returns, GO to Pinpoint Test A |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | TCC solenoid | DTC P0741 is a non-electrical DTC. CLEAR the DTC. If DTC P0741 returns, REFER to: Diagnosis By Symptom . |
| P0742 | Torque Converter Clutch Solenoid Circuit Stuck On | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0742 returns, GO to Pinpoint Test A |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | TCC solenoid | DTC P0740, P0742 and/or P0744 may set, CLEAR the DTC. If DTC P0743 returns, GO to Pinpoint Test A |
| P0744 | Torque Converter Clutch Solenoid Circuit Intermittent | TCC solenoid | DTC P0743 may set, CLEAR the DTC. If DTC P0744 returns, GO to Pinpoint Test A |
| P0748 | Pressure Control Solenoid "A" Electrical | Line Pressure Control (LPC) | DTC P0960, P0962 and/or P0963 may set, CLEAR the DTC. If DTC P0748 returns, GO to Pinpoint Test A |
| P0750 | Shift Solenoid "A" | Shift Solenoid A (SSA) | DTC P0751 may set, CLEAR the DTC. If DTC P0750 returns, GO to Pinpoint Test A |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | SSA | DTC P2700 may set, CLEAR the DTC. If DTC P0751 returns, REFER to: Diagnosis By Symptom . |
| P0752 | Shift Solenoid "A" Stuck On | SSA | CLEAR the DTC. If DTC P0752 returns, REFER to: Diagnosis By Symptom . |
| P0753 | Shift Solenoid "A" Electrical | SSA | DTC P0750, P0973 and/or P0974 may set, CLEAR the DTC. If DTC P0753 returns, GO to Pinpoint Test A |
| P0754 | Shift Solenoid "A" Intermittent | SSA | CLEAR the DTC. If DTC P0754 returns, GO to Pinpoint Test A |
| P0755 | Shift Solenoid "B" | Shift Solenoid B (SSB) | DTC P0756 may set, CLEAR the DTC. If DTC P0755 returns, GO to Pinpoint Test A |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | SSB | DTC P2701 may set, CLEAR the DTC. If DTC P0756 returns, REFER to: Diagnosis By Symptom . |
| P0757 | Shift Solenoid "B" Stuck On | SSB | DTC P2701 may set, CLEAR the DTC. If DTC P0757 returns, REFER to: Diagnosis By Symptom . |
| P0758 | Shift Solenoid "B" Electrical | SSB | DTC P0755, P0976 and/or P0977 may set, CLEAR the DTC. If DTC P0758 returns, GO to Pinpoint Test A |
| P0759 | Shift Solenoid "B" Intermittent | SSB | CLEAR the DTC. If DTC P0759 returns, GO to Pinpoint Test A |
| P0760 | Shift Solenoid "C" | Shift Solenoid C (SSC) | DTC P0761 may set, CLEAR the DTC. If DTC P0760 returns, GO to Pinpoint Test A |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | SSC | DTC P2702 may set, CLEAR the DTC. If DTC P0761 returns, REFER to: Diagnosis By Symptom . |
| P0762 | Shift Solenoid "C" Stuck On | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0762 returns, REFER to: Diagnosis By Symptom . |
| P0763 | Shift Solenoid "C" Electrical | SSC | DTC P0760, P0979 and/or P0980 may set, CLEAR the DTC. If DTC P0763 returns, GO to Pinpoint Test A |
| P0764 | Shift Solenoid "C" Intermittent | SSC | CLEAR the DTC. If DTC P0764 returns, GO to Pinpoint Test A |
| P0765 | Shift Solenoid "D" | Shift Solenoid D (SSD) | DTC P0766 may set, CLEAR the DTC. If DTC P0765 returns, GO to Pinpoint Test A |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | SSD | DTC P2704 may set, CLEAR the DTC. If DTC P0766 returns, REFER to: Diagnosis By Symptom . |
| P0767 | Shift Solenoid "D" Stuck On | SSD | DTC P07A9 and/or P2704 may set, CLEAR the DTC. If DTC P0767 returns, REFER to: Diagnosis By Symptom . |
| P0768 | Shift Solenoid "D" Electrical | SSD | DTC P0765, P0982 and/or P0983 may set, CLEAR the DTC. If DTC P0768 returns, GO to Pinpoint Test A |
| P0769 | Shift Solenoid "D" Intermittent | SSD | CLEAR the DTC. If DTC P0769 returns, GO to Pinpoint Test A |
| P0770 | Shift Solenoid "E" | Shift Solenoid E (SSE) | DTC P0773 may set, CLEAR the DTC. If DTC P0770 returns, GO to Pinpoint Test A |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | SSE | DTC P0984 may set, CLEAR the DTC. If DTC P0771 returns, REFER to: Diagnosis By Symptom . |
| P0772 | Shift Solenoid "E" Stuck On | SSE | DTC P0984 may set, CLEAR the DTC. If DTC P0772 returns, REFER to: Diagnosis By Symptom . |
| P0773 | Shift Solenoid "E" Electrical | SSE | REFER to DTC P0770. |
| P0774 | Shift Solenoid "E" Intermittent | SSE | CLEAR the DTC. If DTC P0774 returns, GO to Pinpoint Test A |
| P07A8 | Transmission Friction Element "D" Stuck Off | Transmission | CLEAR the DTC. If DTC P07A8 returns, REFER to: Diagnosis By Symptom . |
| P07A9 | Transmission Friction Element "D" Stuck On | Transmission | DTC P0767 may set, CLEAR the DTC. If DTC P07A9 returns, REFER to: Diagnosis By Symptom . |
| P07AA | Transmission Friction Element "E" Stuck Off | Transmission | CLEAR the DTC. If DTC P07AA returns, REFER to: Diagnosis By Symptom . |
| P0815 | Upshift Switch Circuit | SelectShift™ switch | CLEAR the DTC. If DTC P0815 returns, REFER to: External Controls . |
| P0816 | Downshift Switch Circuit | SelectShift™ switch | LEAR the DTC. If DTC P0816 returns, REFER to: External Controls . |
| P0826 | Up and Down Switch Circuit | SelectShift™ switch | CHECK SelectShift™ operation, REFER to: External Controls . |
| P0882 | TCM Power Input Signal Low | Battery | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If DTC P0882 returns, REFER to: Charging System - 3.2L Duratorq-TDCi (148kW/200PS) - Puma - System Operation and Component Description . |
| P0883 | TCM Power Input Signal High | Battery | CLEAR the DTC. If DTC P0883 returns, REFER to: Charging System - 3.2L Duratorq-TDCi (148kW/200PS) - Puma - System Operation and Component Description . |
| P0960 | Pressure Control Solenoid "A" Control Circuit/Open | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0960 returns, GO to Pinpoint Test A |
| P0961 | Pressure Control Solenoid "A" Control Circuit Range/Performance | LPC | CLEAR the DTC. If DTC P0961 returns, GO to Pinpoint Test A |
| P0962 | Pressure Control Solenoid "A" Control Circuit Low | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0962 returns, GO to Pinpoint Test A |
| P0963 | Pressure Control Solenoid "A" Control Circuit High | LPC | DTC P0748 may set, CLEAR the DTC. If DTC P0963 returns, GO to Pinpoint Test A |
| P0973 | Shift Solenoid "A" Control Circuit Low | SSA | DTC P0753 may set, CLEAR the DTC. If DTC P0973 returns, GO to Pinpoint Test A |
| P0974 | Shift Solenoid "A" Control Circuit High | SSA | DTC P0748 may set, CLEAR the DTC. If DTC P0974 returns, GO to Pinpoint Test A |
| P0976 | Shift Solenoid "B" Control Circuit Low | SSB | DTC P0758 may set, CLEAR the DTC. If DTC P0976 returns, GO to Pinpoint Test A |
| P0977 | Shift Solenoid "B" Control Circuit High | SSB | DTC P0758 may set, CLEAR the DTC. If DTC P0977 returns, GO to Pinpoint Test A |
| P0979 | Shift Solenoid "C" Control Circuit Low | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0979 returns, GO to Pinpoint Test A |
| P0980 | Shift Solenoid "C" Control Circuit High | SSC | DTC P0763 may set, CLEAR the DTC. If DTC P0980 returns, GO to Pinpoint Test A |
| P0982 | Shift Solenoid "D" Control Circuit Low | SSD | DTC P0768 may set, CLEAR the DTC. If DTC P0982 returns, GO to Pinpoint Test A |
| P0983 | Shift Solenoid "D" Control Circuit High | SSD | DTC P0768 may set, CLEAR the DTC. If DTC P0983 returns, GO to Pinpoint Test A |
| P0984 | Shift Solenoid "E" Range/Performance | SSE | DTC P0771 and/or P0772 may set, CLEAR the DTC. If DTC P0984 returns, REFER to: Diagnosis By Symptom . |
| P1001 | The KOER self-test was unable to complete and KOER aborted. | PCM | RETRIEVE and RECORD all DTCs. REPAIR any self-test or CMDTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the TCM to the latest software. RERUN the KOER self-test. If the DTC returns, INSTALL a new TCM. Refer to: Transmission Control Module (TCM) - 3.2L Duratorq-TDCi (148kW/200PS) - Puma . After installing the new TCM PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P1397 | System Voltage Out Of Self-Test Range | PCM | INSPECT the TCM power and ground circuits for opens or short to ground. INSPECT the TCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RUN the KOEO self-test. If DTC P1397 returns, REFER to: Charging System - 3.2L Duratorq-TDCi (148kW/200PS) - Puma - System Operation and Component Description . |
| P1501 | Vehicle Speed Sensor Out Of Self-Test Range | PCM | Vehicle speed not at 0.0 mph (km/h) during the KOEO and/or KOER self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. If DTC P1501 returns, REFER to: Anti-Lock Brake System (ABS) And Stability Control . |
| P1635 | Tire/Axle Out Of Acceptable Range | PCM | Refer to Engine Controls - Description & Operation (Diesel) . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If DTC P1636 returns, INSTALL a new TCM. Refer to: Transmission Control Module (TCM) - 3.2L Duratorq-TDCi (148kW/200PS) - Puma . After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P163E | Transmission Control Module Programming Error | PCM | CLEAR the DTC. REPROGRAM the original TCM with the latest software. If DTC P163E returns, INSTALL a new TCM. Refer to: Transmission Control Module (TCM) - 3.2L Duratorq-TDCi (148kW/200PS) - Puma . After installing the new, TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P163F | Transmission ID Block Corrupted, Not Programmed | PCM | CLEAR the DTC. REPROGRAM the original TCM with the latest software. If DTC P163F returns, INSTALL a new TCM. Refer to: Transmission Control Module (TCM) - 3.2L Duratorq-TDCi (148kW/200PS) - Puma . After installing the new TCM, PROGRAM it with the latest software and PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P1700 | Transmission Intermittent Failure (failed to neutral) | Transmission | DTC P1700 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . |
| P1702 | Transmission Range Sensor Circuit Intermittent | TR sensor | DTC P0706, P0707 and/or P0708 may set, CLEAR the DTC. If DTC P1702 returns, GO to Pinpoint Test C |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self-Test | TR sensor | CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1705 returns, GO to Pinpoint Test C |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self-Test Range | TFT sensor | CLEAR the DTC and RERUN the KOEO and KOER self-test. |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | TCC | DTC P1744 is a non electrical DTC. CLEAR the DTC. If DTC P1744 returns, REFER to: Diagnosis By Symptom . |
| P177F | Unable To Fully Engage Neutral | Direct or forward clutch pack | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Refer to: Transmission . |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out of Self-Test Range | TCS | CLEAR the DTC. If DTC P1780 returns, REFER to: External Controls . |
| P1783 | Transmission Over Temperature Condition | Transmission | CLEAR the DTC. If DTC P1783 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwiseREFER to: Transmission Cooling . |
| P1910 | Reverse Lamp Control Circuit/Open | Reverse lamps | CLEAR the DTC. TEST system for normal operation. If DTC P1910 returns, REFER to: Reversing Lamps . |
| P1921 | Transmission Range Signal | TR sensor | The engine may not crank. DTC P0706, P0707 and/or P0708 may set. CLEAR the DTC. If DTC P1921 returns, CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1921 returns, GO to Pinpoint Test C |
| P2531 | Ignition Switch Run/Start Position Circuit Low | Ignition switch or circuit fault | CLEAR the DTC. If DTC P2531 returns, REFER to: External Controls . |
| P2535 | Ignition Switch Run/Start Position Circuit High | Ignition switch or circuit fault | CLEAR the DTC. If DTC P2535 returns, REFER to: External Controls . |
| P2610 | ECM/PCM Engine Off Timer Performance | Module communication fault or module | RETRIEVE and ADDRESS any BCM DTCs and RESOLVE them first. If concern still exists, CONFIRM the vehicle is not in transport mode, REFER to: Body Control Module (BCM) . If any CAN DTCs are retrieved between the BCM and the TCM RESOLVE them before proceeding. |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Transmission | DTC P2700 is a non-electrical DTC. DTC P0751 and/or P0752 may set. CLEAR the DTC. If DTC P2700 returns, REFER to: Diagnosis By Symptom . |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Transmission | DTC P2701 is a non-electrical DTC. DTC P0756 and/or P0757 may set. CLEAR the DTC. If DTC P2701 returns, REFER to: Diagnosis By Symptom . |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Transmission | DTC P2702 is a non-electrical DTC. DTC P0761 and/or P0762 may set. CLEAR the DTC. If DTC P2702 returns, REFER to: Diagnosis By Symptom . |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Transmission | DTC P2703 is a non-electrical DTC. DTC P0766 and/or P0768 may set. CLEAR the DTC. If DTC P2703 returns, REFER to: Diagnosis By Symptom . |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | Transmission | DTC P2704 is a non electrical DTC. DTC P0771 and/or P0772 may set. CLEAR the DTC. If DTC P2704 returns, REFER to: Diagnosis By Symptom . |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | Mechanical one-way clutch | DTC P2705 is a non electrical DTC. CLEAR the DTC. If DTC P2705 returns, REFER to: Diagnosis By Symptom . |
| P2758 | Torque Converter Clutch Pressure Control Solenoid Stuck On | TCC | CLEAR the DTC. If DTC P2758 returns, REFER to: Diagnosis By Symptom . |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | TCC | CLEAR the DTC. If DTC P2760 returns, GO to Pinpoint Test A |
| U0028 | Vehicle Communication Bus "A" | Module communication or module fault | A CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC. REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0073 | Control Module Communication Bus "A" Off | Module communication or module fault | A CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC. REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0100 | Lost Communication With ECM / PCM "A" | Module communication or module fault | GO to Pinpoint Test F |
| U0115 | Lost Communication With ECM / PCM "B" | Module communication or module fault | GO to Pinpoint Test G |
| U0121 | Lost Communication With Anti-Lock Brake System (ABS) Control Module | Module communication or module fault | GO to Pinpoint Test G |
| U0129 | Lost Communication with Brake System Control Module "A" | Module communication or module fault | GO to Pinpoint Test H |
| U0140 | Lost Communication With Body Control Module | Module communication or module fault | GO to Pinpoint Test I |
| U0141 | Lost Communication With Body Control Module "A" | Module communication or module fault | GO to Pinpoint Test I |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | Module communication or module fault | GO to Pinpoint Test J |
| U0294 | Lost Communication with Powertrain Control Monitor Module | Module communication or module fault | GO to Pinpoint Test F |
| U0401 | Invalid Data Received from ECM/PCM "A" | Module communication or module fault | This DTC sets when the TCM receives invalid network data from the PCM for the engine speed and vehicle speed input. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. For the correct navigation of all DTCs, REFER to: Body Control Module (BCM) . |
| U0415 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module | Module communication or module fault | This DTC sets when the TCM receives invalid data from the ABS module. DETERMINE which module TCM or ABS module) has been replaced. CARRY OUT the PMI (when the original module is not available) for the module in question. Refer to: Module Configuration - System Operation and Component Description . |
| U0422 | Invalid Data Received from Body Control Module | Module communication or module fault | This DTC sets when the TCM receives invalid BCM data such as global time, engine off time. RETRIEVE and REPAIR all non-network DTCs in the BCM. For the correct navigation of all DTCs, REFER to: Body Control Module (BCM) . |