Parking Aid Module (PAM)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B129C:12 | Left Front Side Sensor: Circuit Short To Battery | REFER to: Parking Aid . |
| B129C:14 | Left Front Side Sensor: Circuit Short To Ground Or Open | REFER to: Parking Aid . |
| B129C:96 | Left Front Side Sensor: Component Internal Failure | REFER to: Parking Aid . |
| B129D:12 | Right Front Side Sensor: Circuit Short To Battery | REFER to: Parking Aid . |
| B129D:14 | Right Front Side Sensor: Circuit Short To Ground Or Open | REFER to: Parking Aid . |
| B129D:96 | Right Front Side Sensor: Component Internal Failure | REFER to: Parking Aid . |
| B129E:73 | Enable/Disable Switch - Semi-Automatic Advanced Parallel Park: Actuator Stuck Closed | REFER to: Parking Aid . |
| B129F:11 | Function LED - Semi-Automatic Advanced Parallel Park: Circuit Short To Ground | REFER to: Parking Aid . |
| B129F:12 | Function LED - Semi-Automatic Parallel Park: Circuit Short To Battery | REFER to: Parking Aid . |
| B13B5:12 | Rear Center Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B13B5:14 | Rear Center Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test D |
| B13B5:96 | Rear Center Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B36:12 | Right Front Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B36:14 | Right Front Outer Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test H |
| B1B36:96 | Right Front Outer Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B38:12 | Right Front Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B38:14 | Right Front Inner Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test H |
| B1B38:96 | Right Front Inner Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B40:12 | Left Front Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B40:14 | Left Front Outer Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test H |
| B1B40:96 | Left Front Outer Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B42:12 | Left Front Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B42:14 | Left Front Inner Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test H |
| B1B42:96 | Left Front Inner Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B44:12 | Right Rear Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B44:14 | Right Rear Outer Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test D |
| B1B44:96 | Right Rear Outer Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B48:12 | Left Rear Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B48:14 | Left Rear Outer Sensor: Circuit Short To Ground Or Open | GO to Pinpoint Test D |
| B1B48:96 | Left Rear Outer Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B54:11 | Function LED - Park Aid: Circuit Short To Ground | GO to Pinpoint Test J |
| B1B54:12 | Function LED - Park Aid: Circuit Short To Battery | GO to Pinpoint Test J |
| B1B57:11 | Front Sensors Power Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| B1B58:11 | Rear Sensors Power Circuit: Circuit Short To Ground | GO to Pinpoint Test C |
| B1C30:73 | Disable Switch - Park Aid: Actuator Stuck Closed | GO to Pinpoint Test K |
| U0001:88 | High Speed Can Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the DTC. REPEAT the Network Test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test L |
| U0101:87 | Lost Communication With TCM: Missing Message | GO to Pinpoint Test M |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test N |
| U0126:87 | Lost Communication With Steering Angle Sensor Module: Missing Message | GO to Pinpoint Test O |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to Pinpoint Test P |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test Q |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U0401:86 | Invalid Data Received From ECM/PCM A: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0402:86 | Invalid Data Received From TCM: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the SOBDMC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0415:86 | Invalid Data Received From ABS Control Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0420:86 | Invalid Data Received From Power Steering Control Module: Signal Invalid | A continuous and on-demand DTC that sets when the PAM receives an invalid network data from the PSCM with a faulted signal data input and or a loss of PSCM synchronization occurred. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in other modules on the network. If no Diagnostic Trouble Codes (DTCs) are present in the PSCM drive the vehicle above 50 km/h (30 mph) for a minimum distance of 1 mile while maintaining a straight ahead vehicle position for at least 30 seconds (this drive cycle needs to occur if the battery has been disconnected or if vehicle is new). If the active park assist is still inoperative and the U0420:86 DTC does not return after driving the vehicle for 1 mile and clearing Diagnostic Trouble Codes (DTCs). DIAGNOSE the observable symptom. |
| U0422:86 | Invalid Data Received From Body Control Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0428:86 | Invalid Data Received From Steering Angle Sensor Module: Signal Invalid | This DTC sets when the Parking Aid Module (PAM) receives invalid network data from the SASM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U100B:67 | Semi-Automatic Parallel Parking System: Signal Incorrect After Event | This DTC sets when the Parking Aid Module (PAM) detects a fault after an active park assist event. RETRIEVE and REPAIR all other Parking Aid Module (PAM) Diagnostic Trouble Codes (DTCs). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U3000:47 | Control Module: Watchdog / Safety Microcontroller Failure | CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTC and REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U3000:55 | Control Module: Not Configured | This DTC sets due to incomplete Parking Aid Module (PAM) programming. CLEAR the DTC and leave the ignition ON for 5 minutes. REPEAT the self-test. If the DTC returns, INSTALL a new Parking Aid Module (PAM). Refer to: Parking Assist Control Module (PAM) . |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to Pinpoint Test R |