Instrumentation, Message Center, And Warning Chimes DTCS: IPC
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1A14:11 | RCM Warning Lamp: Circuit Short To Ground | Refer to IPC Hardware Testing . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS) |
| B1A14:13 | RCM Warning Lamp: Circuit Open | Refer to IPC Hardware Testing . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS) |
| B1A84:41 | Car Configuration Data: General Checksum Failure | This DTC may set after replacement of the IPC. To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. Refer to: Body Control Module (BCM) |
| B1A84:51 | Car Configuration Data: Not Programmed | This DTC may set after replacement of the IPC. To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. Refer to: Body Control Module (BCM) |
| C1D00:00 | Park Brake Apply Switch: No Sub Type Information | GO to Pinpoint Test O |
| C1D22:11 | Steering Wheel Switch Right Module: Circuit Short To Ground | Refer to the appropriate Infotainment article for the procedure. |
| C1D22:23 | Steering Wheel Switch Right Module: Circuit Open | Refer to the appropriate Infotainment article for the procedure. |
| C2003:11 | Steering Wheel Switch Left Module: Circuit Short To Ground | GO to Pinpoint Test AC |
| C2003:23 | Steering Wheel Switch Left Module: Circuit Open | GO to Pinpoint Test AC |
| P1607:81 | MIL Output Circuit: Invalid Serial Data Received | This DTC sets when the IPC receives an invalid MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC P1607:81 returns, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1607:82 | MIL Output Circuit: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC does not receive an updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test AX If DTC P1607:82 returns without DTC U0100:00, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1607:87 | MIL Output Circuit: Missing Message | This DTC sets when the IPC does not receive updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test AX If DTC P1607:87 returns without DTC U0100:00, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test X |
| P1933:68 | Fuel Level Signal: Event Information | GO to Pinpoint Test B |
| U0073:00 | Control Module Communication Bus "A" Off: No Sub Type Information | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC. REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Wiring Diagrams MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0074:00 | Control Module Communication Bus "B" Off: No Sub Type Information | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC. REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AX |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to Pinpoint Test AY |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test AZ |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BA |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BB |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BC |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BD |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test BE |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BF |
| U0208:00 | Lost Communication With "Seat Control Module B": No Sub Type Information | GO to Pinpoint Test BG |
| U0214:00 | Lost Communication With Remote Function Actuator: No Sub Type Information | GO to Pinpoint Test BH |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module-Left: No Sub Type Information | GO to Pinpoint Test BI |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module-Right: No Sub Type Information | GO to Pinpoint Test BI |
| U0252:00 | Lost Communication With Lighting Control Module-Rear "B": No Sub Type Information | GO to Pinpoint Test BJ |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: No Sub Type Information | GO to Pinpoint Test BK |
| U0264:00 | Lost Communication With Camera Module-Rear: No Sub Type Information | GO to Pinpoint Test BL |
| U0401:64 | Invalid Data Received From ECM/PCM A: Signal Plausibility Failure | This DTC sets when a message is temporarily undefined for more than 2 seconds from the PCM for the ambient temperature, fuel economy, engine coolant temperature or engine RPM data. CLEAR the DTC. REPEAT the self-test. If DTC U0401:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PCM. Refer to the appropriate Engine article for the procedure. |
| U0415:64 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Plausibility Failure | This DTC sets when the wheel rotation count message is temporarily undefined for more than 2 seconds from the ABS module for the odometer. CLEAR the DTC. REPEAT the self-test. |
| U0420:68 | Invalid Data Received From Power Steering Control Module: Event Information | This DTC sets when data is invalid from the PSCM. CLEAR the DTC. REPEAT the self-test. If DTC U0420:68 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PSCM. Refer to: Power Steering |
| U0422:00 | Invalid Data or Missing Data Received From Body Control Module: No Sub Type Information | This DTC sets when the fuel level, power mode or vehicle speed message are temporarily undefined for more than 2 seconds or if the TPMS status message is missing for more than 1, 250 milliseconds from the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0422:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM. Refer to: Body Control Module (BCM) |
| U0422:68 | Invalid Data or Missing Data Received From Body Control Module: Event Information | This DTC sets when data is invalid from the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0422:68 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM. Refer to: Body Control Module (BCM) |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This DTC sets when the temperature range data is invalid for more than 2 seconds from the HVAC module through the BCM. CLEAR the DTC. REPEAT the self-test. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC sets when data is invalid from the RCM. CLEAR the DTC. REPEAT the self-test. |
| U0558:00 | Invalid Data Received From Front Controls/Display Interface Module: No Sub Type Information | This DTC sets when data is invalid from the FCDIM for longer than 2 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0558:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the FCDIM. Refer to the appropriate Infotainment article for the procedure. |
| U0564:00 | Invalid Data Received From Speech Recognition Module: No Sub Type Information | This DTC sets when data is invalid from the APIM for longer than 2 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0564:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the APIM. Refer to the appropriate Infotainment article for the procedure. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2101:01 | Control Module Configuration Incompatible: General Electrical Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:41 returns, Refer to IPC Hardware Testing . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:44 returns, Refer to IPC Hardware Testing . |
| U3006:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to Pinpoint Test BM |
| U3006:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to Pinpoint Test BN |