Automatic Transmission DTCS: 6F35
DTC INDEX
| DTC | Description | Component | Action |
|---|---|---|---|
| P0657 | Actuator Supply Voltage A Circuit Open | Solenoid power control | Power to all solenoids has been interrupted, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F . |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)). | DTCs P2700, P2701, P2702, P2703 and/or P2704 may set. CLEAR the DTCs. If the DTC returns, GO to Symptom Chart . |
| P0702 | Transmission Control System Electrical | Transmission Control System Electrical | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If the DTC returns, REFER to Battery, Mounting and Cables . |
| P0706 | TR Sensor A Circuit Range/Performance | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0707 | TR Sensor A Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0708 | TR Sensor A Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . |
| P0710 | TFT Sensor A Circuit | TFT | DTCs P0712 or P0713 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0711 | TFT Sensor A Circuit Range/Performance | TFT | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0712 | TFT Sensor A Circuit Low | TFT | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0713 | TFT Sensor A Circuit High | TFT | DTC P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G . REPAIR the more specific DTC first. |
| P0715 | Turbine/Input Shaft Speed Sensor A Circuit | TSS sensor | DTC P0717 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . REPAIR the more specific DTC first. |
| P0717 | Turbine/Input Shaft Speed Sensor A Circuit No Signal | TSS sensor | DTC P0715 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . REPAIR the more specific DTC first. |
| P0718 | Turbine/Input Shaft Speed Sensor A Circuit Intermittent | TSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K . |
| P0720 | OSS Sensor Circuit | OSS sensor | DTC P0722 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . REPAIR the more specific DTC first. |
| P0721 | OSS Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . |
| P0722 | OSS Sensor Circuit No Signal | OSS sensor | DTC P0720 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L . REPAIR the more specific DTC first. |
| P0729 | Gear 6 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 5-6 shift/harsh/soft/slipping. |
| P0731 | Gear 1 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0732 | Gear 2 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0733 | Gear 3 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0734 | Gear 4 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0735 | Gear 5 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 4-5 shift/harsh/soft/slipping. |
| P073D | Unable to Engage Neutral | Transmission forward or direct clutch packs | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Transaxle - Overhaul . |
| P0740 | TCC Clutch Solenoid Circuit/Open | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P0741 | TCC Solenoid Circuit Performance/Stuck Off | TCC Solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0742 | TCC Solenoid Circuit Stuck On | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P0743 | TCC Solenoid Circuit Electrical | TCC Solenoid electrical faults | DTCs P0740, P0742 and/or P0744 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . REPAIR the more specific DTC first. |
| P0744 | TCC Solenoid Circuit Intermittent | TCC Solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . REPAIR the more specific DTC first. |
| P0748 | LPC A Electrical | Line pressure control (LPC) Solenoid electrical faults | DTCs P0960, P0962 and/or P0963 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0750 | SSA | Shift Solenoid A (SSA) electrical faults | DTC P0751 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0751 | SSA Performance/Stuck Off | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | DTC P2700 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no forward. |
| P0752 | SSA Stuck On | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 1, 2, 3, 4 available. |
| P0753 | SSA Electrical | SSA electrical faults | DTCs P0750, P0973 and/or P0974 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0754 | SSA Intermittent | SSA electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . |
| P0755 | SSB | SSB electrical faults | DTC P0756 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0756 | SSB Performance/Stuck Off | SSB electrical faults | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 3 and 5 available. |
| P0757 | SSB Stuck On | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) SSB electrical faults, SSB electrical faults | DTC P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P0758 | SSB Electrical | SSB electrical faults | DTCs P0755, P0976 and/or P0977 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0759 | SSB Intermittent | SSB electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . |
| P0760 | SSC | Shift solenoid C (SSC) electrical faults | DTC P0761 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0761 | SSC Performance/Stuck Off | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P2702 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 1-2 shift/harsh/soft/slipping. |
| P0762 | SSC Stuck On | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 2 and 6 available. |
| P0763 | SSC Electrical | SSC electrical faults | DTCs P0760, P0979 and/or P0980 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0764 | SSC Intermittent | SSC electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . |
| P0765 | SSD | SSD electrical faults | DTC P0766 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0766 | SSD Performance/Stuck Off | SSD electrical faults | DTC P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P0767 | SSD Stuck On | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTCs P07A9 and/or P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0768 | SSD Electrical | SSD electrical faults | DTCs P0765, P0982 and/or P0983 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0769 | SSD Intermittent | SSD electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . |
| P0770 | SSE | Shift Solenoid E (SSE) electrical faults | DTC P0773 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . REPAIR the more specific DTC first. |
| P0771 | SSE Performance/Stuck Off | SSE Non-electrical faults (SSE and main control valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns. |
| P0772 | SSE Stuck On | SSE Non-electrical faults (SSE and valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P0773 | SSE Electrical | SSE electrical faults | DTC P0770 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . REPAIR the more specific DTC first. |
| P0774 | SSE Intermittent | SSE electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E . |
| P07A5 | Transmission Friction Element "B" Stuck On | Direct clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 2-3 shift/harsh/soft/slipping. |
| P07A8 | Transmission Friction Element "D" Performance/Stuck Off | Low/reverse clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or only gears 1 and R available. |
| P07A9 | Transmission Friction Element "D" Stuck On | Low/reverse clutch | DTC P0767 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse and for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P07AA | Transmission Friction Element "E" Performance/Stuck Off | Overdrive clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns. |
| P0815 | Upshift Switch Circuit | Upshift switch electrical | REFER to Automatic Transmission External Controls . |
| P0816 | Downshift Switch Circuit | Downshift switch electrical | REFER to Automatic Transmission External Controls . |
| P0867 | Transmission Fluid Pressure | Transmission hydraulic and clutch systems | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0882 | PCM Power Input Signal Low | PCM power input signal low | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to Charging System . |
| P0883 | PCM Power Input Signal High | PCM power input signal high | CLEAR the DTC. If the DTC returns, REFER to Charging System . |
| P0960 | LPC A Control Circuit/Open | Line Pressure Control (LPC) solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0961 | LPC A Control Circuit Range/Performance | LPC solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . |
| P0962 | LPC A Control Circuit Low | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0963 | LPC A Control Circuit High | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I . REPAIR the more specific DTC first. |
| P0973 | SSA Control Circuit Low | SSA electrical faults | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0974 | SSA Control Circuit High | SSA electrical faults | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A . REPAIR the more specific DTC first. |
| P0976 | SSB Control Circuit Low | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0977 | SSB Control Circuit High | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B . REPAIR the more specific DTC first. |
| P0979 | SSC Control Circuit Low | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0980 | SSC Control Circuit High | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C . REPAIR the more specific DTC first. |
| P0982 | SSD Control Circuit Low | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0983 | SSD Control Circuit High | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D . REPAIR the more specific DTC first. |
| P0984 | SSE Control Circuit Range/Performance | SSE electrical faults | DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTCs returns, GO to Symptom Chart for engagement concerns. |
| P1001 | KOER Not Able to Complete, KOER Aborted | PCM | READ and RECORD all DTCs. REPAIR any self-test or continuous DTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the PCM to the latest calibration. RERUN the KOER self-test. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing the new PCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . Road test the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P1397 | System Voltage Out Of Self Test Range | System voltage out of self test range | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If the DTC returns, REFER to Charging System . |
| P1501 | VSS Out Of Self Test Range | System voltage out of self test range | CLEAR the DTC. If the DTC returns, PLACE selector lever in park and monitor the VSS PID. VERIFY the VSS input is at 0. RERUN self-test procedure. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing the new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . ROAD TEST the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P163E | PCM Programming Error | PCM programming error | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing a new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . ROAD TEST the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P163F | Transmission ID Block Corrupted, Not Programmed | Transmission id memory block corrupted, not programmed | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing a new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . ROAD TEST the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P1702 | TR Sensor Circuit Intermittent | TR sensor electrical faults | DTCs P0706, P0707 and/or P0708 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . REPAIR the more specific DTC first. |
| P1705 | TR Circuit Not Indicating Park/Neutral During Self Test | TR sensor | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1711 | TFT Sensor Out Of Self Test Range | TFT | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1744 | TCC Solenoid Circuit | TCC System Faults (includes TCC, main control valve body and non-electrical solenoid faults) | DTC P1744 is a non-electrical DTC. CLEAR the DTC. If the DTCs returns, GO to Symptom Chart for torque converter operation concerns/no apply. |
| P177F | Unable To Fully Engage Neutral | Internal transmission failure | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Transaxle - Overhaul |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out Of Self Test Range | Transmission control switch | REFER to Automatic Transmission External Controls . |
| P1783 | Transmission Over Temperature Condition | Transmission over temperature | MONITOR the TFT sensor PID and TCC PID. Road test the vehicle and MONITOR the TFT sensor and TCC solenoid electrical operation. If DTC P0741 is set, REPAIR DTC P0741 first. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P1910 | Reverse Lamp Control Circuit/Open | Reverse lamp control | CLEAR the DTC. If the DTC returns, REFER to Exterior Lighting . |
| P1921 | TR Signal | TR sensor | Engine may not crank. DTCs P0706, P0707 and/or P0708 may set. CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J . REPAIR the more specific DTC first. |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | DTC P2700 is a non-electrical DTC. DTCs P0751 and/or P0752 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns, no forward or delayed/soft forward and/or shift concerns/only gears 1, 2, 3, 4 available. |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) | DTC P2701 is a non-electrical DTC. DTCs P0756 and/or P0757 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/only gears 3 and 5 available. |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P2702 is a non-electrical DTC. DTCs P0761 and/or P0762 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns, no 1-2 shift/harsh/soft/slipping or no 5-6 shift/harsh/soft/slipping or only gears 2 and 6 available. |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Low/reverse clutch and OWC faults | DTC P2703 is a non-electrical DTC. DTCs P0766 and/or P0768 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for engagement concerns/no reverse. |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTC P2704 is a non-electrical DTC. DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for shift concerns/no 3-4 shift/harsh/soft/slipping. |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | OWC faults | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, GO to Symptom Chart engagement concerns/neutral after launch. |
| P2760 | TCC Pressure Control Solenoid Intermittent | TCC | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H . |
| P2783 | Torque Converter Temperature Too High | TCC | TCC control valve stuck in the apply position. CLEAR the DTC. If the DTC returns, GO to Symptom Chart for torque converter operation concerns/no apply. |