Automatic Transmission DTCS: 6F50/6F55
DTC INDEX
| Description | Component | Action | |
|---|---|---|---|
| P0657 | Actuator Supply Voltage "A" Circuit Open | Solenoid power control | Power to all solenoids has been interrupted, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test F for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test R for 3.5L GTDI engines. |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)). | DTCs P2700, P2701, P2702, P2703 and/or P2704 may set. CLEAR the DTCs. If the DTC returns, GO to Symptom Chart . |
| P0702 | Transmission Control System Electrical | Transmission Control System Electrical | This sets with P0882 (system voltage low) and P0883 (system voltage high). INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTCs. If the DTCs returns, REFER to Charging System . |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
| P0707 | Transmission Range Sensor "A" Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
| P0708 | Transmission Range Sensor "A" Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
| P0709 | TR Sensor A Circuit Intermittent | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
DTC INDEX
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | TFT | DTCs P0712 or P0713 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test S for 3.5L GTDI engines. |
|---|---|---|---|
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | TFT | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test S for 3.5L GTDI engines. |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | TFT | P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test S for 3.5L GTDI engines. |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | TFT | P0710 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test G for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test S for 3.5L GTDI engines. |
| P0715 | Turbine/Input Shaft Speed Sensor "A" Circuit | TSS sensor | P0717 may set, GO to Pinpoint Test K for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test W for 3.5L GTDI engines. |
| P0717 | Turbine/Input Shaft Speed Sensor "A" Circuit No Signal | TSS sensor | P0715 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test W for 3.5L GTDI engines. |
| P0718 | Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent | TSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test K for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test W for 3.5L GTDI engines. |
| P0720 | Output Shaft Speed Sensor Circuit | OSS sensor | P0722 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test X for 3.5L GTDI engines. |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test X for 3.5L GTDI engines. |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | OSS sensor | P0720 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test L for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test X for 3.5L GTDI engines. |
| P0729 | Gear 6 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0731 | Gear 1 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0732 | Gear 2 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0733 | Gear 3 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0734 | Gear 4 Incorrect Ratio | O/D Clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0735 | Gear 5 Incorrect Ratio | Direct Clutch system faults (includes non-electrical SSB faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P073D | Unable to Engage Neutral | Transmission forward or direct clutch packs | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Transaxle - Overhaul . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | TCC Solenoid electrical faults | P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test T for 3.5L GTDI engines. |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | TCC Solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0742 | Torque Converter Clutch Solenoid Circuit Stuck On | TCC Solenoid electrical faults | P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test T for 3.5L GTDI engines. |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | TCC Solenoid electrical faults | DTCs P0740, P0742 and/or P0744 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test T for 3.5L GTDI engines. |
| P0744 | Torque Converter Clutch Solenoid Circuit Intermittent | TCC Solenoid electrical faults | P0743 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test T for 3.5L GTDI engines. |
| P0748 | Pressure Control Solenoid "A" Electrical | Line pressure control (LPC) Solenoid electrical faults | DTCs P0960, P0962 and/or P0963 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test U for 3.5L GTDI engines. |
| P0750 | Shift Solenoid "A" | Shift Solenoid A (SSA) electrical faults | P0751 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test M for 3.5L GTDI engines. |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | P2700 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0752 | Shift Solenoid "A" Stuck On | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0753 | Shift Solenoid "A" Electrical | SSA electrical faults | DTCs P0750, P0973 and/or P0974 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test M for 3.5L GTDI engines. |
| P0754 | Shift Solenoid "A" Intermittent | SSA electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test M for 3.5L GTDI engines. |
| P0755 | Shift Solenoid "B" | SSB electrical faults | P0756 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test N for 3.5L GTDI engines. |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | SSB electrical faults | P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0757 | Shift Solenoid "B" Stuck On | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) SSB electrical faults, SSB electrical faults | P2701 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0758 | Shift Solenoid "B" Electrical | SSB electrical faults | DTCs P0755, P0976 and/or P0977 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test N for 3.5L GTDI engines. |
| P0759 | Shift Solenoid "B" Intermittent | SSB electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test N for 3.5L GTDI engines. |
| P0760 | Shift Solenoid "C" | Shift solenoid C (SSC) electrical faults | P0761 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test O for 3.5L GTDI engines. |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | P2702 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0762 | Shift Solenoid "C" Stuck On | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | P0763 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0763 | Shift Solenoid "C" Electrical | SSC electrical faults | DTCs P0760, P0979 and/or P0980 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test O for 3.5L GTDI engines. |
| P0764 | Shift Solenoid "C" Intermittent | SSC electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test O for 3.5L GTDI engines. |
| P0765 | Shift Solenoid "D" | SSD electrical faults | P0766 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test P for 3.5L GTDI engines. |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | SSD electrical faults | P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0767 | Shift Solenoid "D" Stuck On | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTCs P07A9 and/or P2704 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0768 | Shift Solenoid "D" Electrical | SSD electrical faults | DTCs P0765, P0982 and/or P0983 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test P for 3.5L GTDI engines. |
| P0769 | Shift Solenoid "D" Intermittent | SSD electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test P for 3.5L GTDI engines. |
| P0770 | Shift Solenoid "E" | Shift Solenoid E (SSE) electrical faults | P0773 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test Q for 3.5L GTDI engines. |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | SSE Non-electrical faults (SSE and main control valve body) | P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0772 | Shift Solenoid "E" Stuck On | SSE Non-electrical faults (SSE and valve body) | P0984 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0773 | Shift Solenoid "E" Electrical | SSE electrical faults | P0770 may set, GO to Pinpoint Test E for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test Q for 3.5L GTDI engines. |
| P0774 | Shift Solenoid "E" Intermittent | SSE electrical faults | P0770 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test E for 3.5L Ti-VCT engines or GO to Pinpoint Test Q for 3.5L GTDI engines. |
| P07A5 | Transmission Friction Element "B" Stuck On | Direct clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P07A8 | Transmission Friction Element "D" Performance/Stuck Off | Low/reverse clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P07A9 | Transmission Friction Element "D" Stuck On | Low/reverse clutch | P0767 may set, CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P07AA | Transmission Friction Element "E" Performance/Stuck Off | Overdrive clutch | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0815 | Upshift Switch Circuit | Upshift switch electrical | REFER to Automatic Transmission External Controls . |
| P0816 | Downshift Switch Circuit | Downshift switch electrical | REFER to Automatic Transmission External Controls . |
| P0867 | Transmission Fluid Pressure | Transmission hydraulic and clutch systems | CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P0882 | TCM Power Input Signal Low | TCM power input signal low | This sets with P0702. INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTCs. If the DTC returns, REFER to Charging System . |
| P0883 | TCM Power Input Signal High | TCM power input signal high | This sets with P0702. CLEAR the DTCs. If the DTC returns, REFER to Charging System . |
| P0960 | Pressure Control Solenoid "A" Control Circuit/Open | Line Pressure Control (LPC) solenoid electrical faults | P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test U for 3.5L GTDI engines. |
| P0961 | Pressure Control Solenoid "A" Control Circuit Range/Performance | LPC solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test U for 3.5L GTDI engines. |
| P0962 | Pressure Control Solenoid "A" Control Circuit Low | LPC solenoid electrical faults | P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test U for 3.5L GTDI engines. |
| P0963 | Pressure Control Solenoid "A" Control Circuit High | LPC solenoid electrical faults | P0748 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test I for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test U for 3.5L GTDI engines. |
| P0973 | Shift Solenoid "A" Control Circuit Low | SSA electrical faults | P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test M for 3.5L GTDI engines. |
| P0974 | Shift Solenoid "A" Control Circuit High | SSA electrical faults | P0753 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test A for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test M for 3.5L GTDI engines. |
| P0976 | Shift Solenoid "B" Control Circuit Low | SSB electrical faults | P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test N for 3.5L GTDI engines. |
| P0977 | Shift Solenoid "B" Control Circuit High | SSB electrical faults | P0758 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test B for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test N for 3.5L GTDI engines. |
| P0979 | Shift Solenoid "C" Control Circuit Low | SSC electrical faults | P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test O for 3.5L GTDI engines. |
| P0980 | Shift Solenoid "C" Control Circuit High | SSC electrical faults | P0763 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test C for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test O for 3.5L GTDI engines. |
| P0982 | Shift Solenoid "D" Control Circuit Low | SSD electrical faults | P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test P for 3.5L GTDI engines. |
| P0983 | Shift Solenoid "D" Control Circuit High | SSD electrical faults | P0768 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test D for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test P for 3.5L GTDI engines. |
| P0984 | Shift Solenoid "E" Control Circuit Range/Performance | SSE electrical faults | DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTCs returns, GO to Symptom Chart . |
| P1001 | KOER Not Able to Complete, KOER Aborted | PCM | RETRIEVE and RECORD all DTCs. REPAIR any self-test or continuous DTCs first. CLEAR the DTC. If the DTC returns, REPROGRAM the original PCM to the latest calibration. If the DTCs return, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing the new PCM, PROGRAM it with the latest calibration and PERFORM the Solenoid Body Strategy Download. REFER to Solenoid Body Strategy Download . Road test the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P1397 | System Voltage Out Of Self Test Range | System voltage out of self test range | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If the DTC returns, REFER to Charging System . |
| P1501 | Vehicle Speed Sensor Out Of Self Test Range | System voltage out of self test range | CLEAR the DTC. If the DTC returns, PLACE selector lever in park and monitor the VSS PID. VERIFY the VSS input is at 0. RERUN self-test procedure. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . After installing the new PCM, PROGRAM with the latest calibration and PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . ROAD TEST the vehicle and PERFORM the Solenoid Body Strategy Drive Cycle . |
| P163E | Transmission Control Module Programming Error | TCM programming error | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . |
| P163F | Transmission ID Block Corrupted, Not Programmed | Transmission id memory block corrupted, not programmed | CLEAR the DTC. If the DTC returns, REPROGRAM the PCM to the latest calibration. If the DTC returns, INSTALL a new PCM. REFER to Electronic Engine Controls . PERFORM the Solenoid Body Strategy Data Download. REFER to Solenoid Body Strategy Download . |
| P1702 | Transmission Range Sensor Circuit Intermittent | TR sensor electrical faults | DTCs P0706, P0707 and/or P0708 may set, CLEAR the DTC. If the DTC returns, GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test | TR sensor | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self Test Range | TFT | CLEAR the DTC. RERUN the KOEO and KOER self-test. |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | TCC System Faults (includes TCC, main control valve body and non-electrical solenoid faults) | P1744 is a non-electrical DTC. CLEAR the DTC. If the DTCs returns, GO to Symptom Chart . |
| P177F | Unable to Engage Neutral | Direct or forward clutch pack | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Transaxle - Overhaul |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out Of Self Test Range | Transmission control switch | REFER to Automatic Transmission External Controls . |
| P1783 | Transmission Overtemperature Condition | Transmission over temperature | CLEAR the DTC. If the DTC returns, Automatic Transmission Cooling System 6F50/6F55 . |
| P1910 | Reverse Lamp Control Circuit/Open | Reverse lamp control | CLEAR the DTC. If the DTC returns, REFER to Exterior Lighting . |
| P1921 | Transmission Range Signal | TR sensor | Engine may not crank. DTCs P0706, P0707 and/or P0708 may set. CLEAR the DTC. If the DTC returns, REPAIR the more specific DTC first. GO to Pinpoint Test J for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test V for 3.5L GTDI engines. |
| P1934 | Vehicle Speed Signal | VSS | CLEAR the DTC. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control |
| P193F | Vehicle Speed Signal Intermittent | VSS | CLEAR the DTC. If the DTC returns, REFER to Anti-Lock Brake System (ABS) and Stability Control |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Forward clutch system faults (includes nonelectrical SSA faults, valve body and clutch) | DTC P2700 is a non-electrical DTC. DTCs P0751 and/or P0752 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Direct clutch system fault (includes non-electrical SSB faults, valve body and clutch) | DTC P2701 is a non-electrical DTC. DTCs P0756 and/or P0757 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Intermediate clutch system faults (includes clutch, valve body and nonelectrical SSC faults) | DTC P2702 is a non-electrical DTC. DTCs P0761 and/or P0762 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Low/reverse clutch and OWC faults | DTC P2703 is a non-electrical DTC. DTCs P0766 and/or P0768 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | O/D clutch system faults (includes non-electrical SSD faults, valve body and clutch) | DTC P2704 is a non-electrical DTC. DTCs P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | OWC faults | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | TCC | CLEAR the DTC. If the DTC returns, GO to Pinpoint Test H for 3.5L/3.7L Ti-VCT engines or GO to Pinpoint Test T for 3.5L GTDI engines. |
| P2783 | Torque Converter Temperature Too High | TCC | TCC control valve stuck in the apply position. CLEAR the DTC. If the DTC returns, GO to Symptom Chart . |