With Rear Parking Aid
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1B36:12 | Right Front Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B36:14 | Right Front Outer Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test H |
| B1B36:96 | Right Front Outer Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B38:12 | Right Front Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B38:14 | Right Front Inner Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test H |
| B1B38:96 | Right Front Inner Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B40:12 | Left Front Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B40:14 | Left Front Outer Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test H |
| B1B40:96 | Left Front Outer Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B42:12 | Left Front Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B1B42:14 | Left Front Inner Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test H |
| B1B42:96 | Left Front Inner Sensor: Component Internal Failure | GO to Pinpoint Test I |
| B1B44:12 | Right Rear Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B44:14 | Right Rear Outer Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test D |
| B1B44:96 | Right Rear Outer Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B46:12 | Right Rear Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B46:14 | Right Rear Inner Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test D |
| B1B46:96 | Right Rear Inner Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B48:12 | Left Rear Outer Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B48:14 | Left Rear Outer Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test D |
| B1B48:96 | Left Rear Outer Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B50:12 | Left Rear Inner Sensor: Circuit Short To Battery | GO to Pinpoint Test E |
| B1B50:14 | Left Rear Inner Sensor: Circuit Short To Ground or Open | GO to Pinpoint Test D |
| B1B50:96 | Left Rear Inner Sensor: Component Internal Failure | GO to Pinpoint Test F |
| B1B52:12 | Rear Sounder - Park Aid: Circuit Short To Battery | GO to Pinpoint Test L |
| B1B52:14 | Rear Sounder - Park Aid: Circuit Short To Ground or Open | GO to Pinpoint Test L |
| B1B53:12 | Front Sounder - Park Aid: Circuit Short To Battery | GO to Pinpoint Test M |
| B1B53:14 | Front Sounder - Park Aid: Circuit Short To Ground or Open | GO to Pinpoint Test M |
| B1B54:11 | Function LED - Park Aid: Circuit Short To Ground | GO to Pinpoint Test J |
| B1B54:12 | Function LED - Park Aid: Circuit Short To Battery | GO to Pinpoint Test J |
| B1B57:11 | Front Sensors Power Circuit: Circuit Short To Ground | GO to Pinpoint Test B |
| B1B58:11 | Rear Sensors Power Circuit: Circuit Short To Ground | GO to Pinpoint Test C |
| B1C30:73 | Disable Switch - Park Aid: Actuator Stuck Closed | GO to Pinpoint Test K |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC). CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test N |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test O |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test P |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the DTC and TEST the system for normal operation. If the DTC returns, INSTALL a new PAM. |
| U0401:86 | Invalid Data Received From ECM/PCM A: Signal Invalid | This DTC sets when the PAM receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0415:86 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Invalid | This DTC sets when the PAM receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0422:86 | Invalid Data Received From Body Control Module: Signal Invalid | This DTC sets when the PAM receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the BCM and IPC. If this DTC is still present after any IPC and BCM Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL as-built data from Professional Technician Society (PTS). If this DTC returns, INSTALL a new PAM. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) in the BCM and IPC. If this DTC is still present after any IPC and BCM Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL as-built data from Professional Technician Society (PTS). If this DTC returns, INSTALL a new PAM. |
| U3000:47 | Control Module: Watchdog / Safety Microcontroller Failure | CLEAR the DTC and turn the ignition OFF. Turn the ignition ON, wait 10 seconds and TEST the system for normal operation. If the DTC returns, INSTALL a new PAM. |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTC and turn the ignition OFF. Turn the ignition ON, wait 10 seconds and TEST the system for normal operation. If the DTC returns, INSTALL a new PAM. |
| U3000:55 | Control Module: Not Configured | INSTALL as-built data from Professional Technician Society (PTS) and TEST the system for normal operation. If this DTC returns, INSTALL a new PAM. |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to Pinpoint Test Q |