Body Closures: RGTM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B10D0:23 | Trunk Latch Clutch Switch: Signal Stuck Low | GO to Pinpoint Test K |
| B113E:23 | External Boot/Trunk Release Switch: Signal Stuck Low | GO to Pinpoint Test B |
| B1161:15 | Left Rear Anti-Pinch Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test G |
| B1162:15 | Right Rear Anti-Pinch Sensor: Circuit Short To Battery or Open | GO to Pinpoint Test G |
| B11C4:23 | Boot/Trunk Close Button: Signal Stuck Low | GO to Pinpoint Test B |
| B1219:12 | Interior Boot/Trunk Release Switch: Circuit Short To Battery | GO to Pinpoint Test B |
| B1219:23 | Interior Boot/Trunk Release Switch: Signal Stuck Low | GO to Pinpoint Test B |
| B1316:02 | Boot/Trunk Latch Power Close Unit: General Signal Failure | GO to Pinpoint Test K |
| B1316:93 | Boot/Trunk Latch Power Close Unit: No Operation | GO to Pinpoint Test K |
| C2005:11 | Right Actuator: Circuit Short To Ground | GO to Pinpoint Test A |
| C2005:12 | Right Actuator: Circuit Short To Battery | GO to Pinpoint Test A |
| C2005:13 | Right Actuator: Circuit Open | GO to Pinpoint Test A |
| C2005:15 | Right Actuator: Circuit Short To Battery or Open | GO to Pinpoint Test A |
| C2005:19 | Right Actuator: Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2005:31 | Right Actuator: No Signal | GO to Pinpoint Test A |
| C2006:11 | Left Actuator: Circuit Short To Ground | GO to Pinpoint Test A |
| C2006:12 | Left Actuator: Circuit Short To Battery | GO to Pinpoint Test A |
| C2006:13 | Left Actuator: Circuit Open | GO to Pinpoint Test A |
| C2006:15 | Left Actuator: Circuit Short To Battery or Open | GO to Pinpoint Test A |
| C2006:19 | Left Actuator: Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2006:31 | Left Actuator: No Signal | GO to Pinpoint Test A |
| U0010:88 | Medium Speed CAN Communication Bus: Bus Off | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the diagnostic scan tool to report this DTC). VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test L |
| U0214:00 | Lost Communication With Remote Function Actuation: No Sub Type Information | GO to Pinpoint Test M |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CARRY OUT the PMI procedure using As-Built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U0300:00 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U0401:68 | Invalid Data Received From ECM/PCM A: Event Information | DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs) from the PCM. REFER to: ELECTRONIC ENGINE CONTROLS - PLUG-IN HYBRID ELECTRIC VEHICLE (PHEV) . |
| U0422:68 | Invalid Data Received From Body Control Module: Event Information | DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs) from the BCM. REFER to: Body Control Module (BCM) . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CARRY OUT the PMI procedure using As-Built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U201A:51 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U201A:52 | Control Module Main Calibration Data: Not Activated | CARRY OUT the PMI procedure using As-Built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U201A:52 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CARRY OUT the PMI procedure using As-Built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U2100:00 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CARRY OUT the PMI procedure using As-Built data. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U2101:00 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U2101:00 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:45 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:46 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:49 returns, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) . |
| U3000:4B | Control Module: Over Temperature | DIAGNOSE the ambient air temperature sensor input. REFER to: Instrumentation, Message Center and Warning Chimes . |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to Pinpoint Test N |