Wiper System & Washer System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1008:23 | Wiper Mode Switch: Signal Stuck Low | INSTALL a new wiper/washer switch. REFER to: Steering Column Multifunction Switch RH
. CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| B1051:92 | Front Washer Switch: Performance or Incorrect Operation | INSTALL a new wiper/washer switch. REFER to: Steering Column Multifunction Switch RH
. CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| B1052:92 | Rear Washer Switch: Performance or Incorrect Operation | INSTALL a new wiper/washer switch. REFER to: Steering Column Multifunction Switch RH
. CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) . |
| B1095:11 | Wiper On/Off Relay: Circuit Short To Ground | GO to Pinpoint Test E |
| B1095:12 | Wiper On/Off Relay Circuit Short To Battery | GO to Pinpoint Test A |
| B1095:13 | Wiper On/Off Relay: Circuit Open | GO to Pinpoint Test A |
| B1095:14 | Wiper On/Off Relay Circuit Short To Ground or Open | If the windshield wipers are inoperative, GO to Pinpoint Test A If the windshield wipers are continuously on, GO to Pinpoint Test E |
| B1095:19 | Wiper On/Off Relay: Circuit Current Above Threshold | GO to Pinpoint Test A |
| B1096:11 | Wiper High/Low Relay: Circuit Short To Ground | GO to Pinpoint Test C |
| B1096:12 | Wiper High/Low Relay: Circuit Short To Battery | GO to Pinpoint Test D |
| B1096:13 | Wiper High/Low Relay: Circuit Open | GO to Pinpoint Test D |
| B1096:14 | Wiper High/Low Relay: Circuit Short To Ground or Open | If the low speed windshield wiper setting is inoperative, GO to Pinpoint Test C If the high speed windshield wiper setting is inoperative, GO to Pinpoint Test D |
| B1096:19 | Wiper High/Low Relay: Circuit Current Above Threshold | GO to Pinpoint Test D |
| B10AD:04 | Rain Sensor: System Internal Failure | INSTALL a new rain sensor. REFER to: Rain Sensor . |
| B10AD:06 | Rain sensor: Algorithm Based Failure | INSTALL a new rain sensor. REFER to: Rain Sensor . |
| B10AD:83 | Rain Sensor: Value of Signal Protection Calculation Incorrect | GO to Pinpoint Test G |
| B112B:87 | Steering Wheel Module: Missing Message | GO to Pinpoint Test B |
| B1C45:13 | Front Wiper Park Position Switch: Circuit Open | GO to Pinpoint Test H |
| B1C77:11 | Rear Wiper Relay: Circuit Short To Ground | GO to Pinpoint Test J |
| B1C77:12 | Rear Wiper Relay: Circuit Short To Battery | GO to Pinpoint Test J |
| B1C77:13 | Rear Wiper Relay: Circuit Open | GO to Pinpoint Test J |
| B1C77:14 | Rear Wiper Relay: Circuit Short To Ground Or Open | If the rear window wiper is inoperative, GO to Pinpoint Test J If the rear window wiper is continuously on, GO to Pinpoint Test K |
| B1C77:19 | Rear Wiper Relay: Circuit Current Above Threshold | GO to Pinpoint Test J |
| U0231:00 | Lost Communication With Rain Sensing Module: No Sub Type Information | GO to Pinpoint Test G |
| All other Diagnostic Trouble Codes (DTCs) | - | REFER to: Body Control Module (BCM) . |