Information System And Entertainment System DTCS: Sync: FCDIM
| DTC | Description | Action |
|---|---|---|
| B10BD:11 | Multifunctional Switch: Circuit Short To Ground | GO to Pinpoint Test S |
| B10BD:13 | Multifunctional Switch: Circuit Open | GO to Pinpoint Test S |
| B10BD:23 | Multifunctional Switch: Signal Stuck Low | GO to Pinpoint Test S |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test Y |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test Z |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0264:00 | Lost Communication With Camera Module - Rear: No Sub Type Information | GO to Pinpoint Test X |
| U0423:68 | Invalid Data Received from Instrument Panel Cluster Control Module: Event Information | RETRIEVE and DIAGNOSE Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes
. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U2013:87 | Switch Pack: Missing Message | GO to Pinpoint Test T |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3003:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to Pinpoint Test AC |
| U3003:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to Pinpoint Test AD |