Instrumentation, Message Center, And Warning Chimes DTCS: IPC
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1A14:11 | RCM Warning Lamp: Circuit Short To Ground | DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . |
| B1A14:13 | RCM Warning Lamp: Circuit Open | DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . |
| B1A84:41 | Car Configuration Data: General Checksum Failure | This DTC may set after replacement of the IPC. To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. REFER to: Body Control Module (BCM) . |
| B1A84:51 | Car Configuration Data: Not Programmed | This DTC may set after replacement of the IPC. To CLEAR this DTC CARRY OUT the car configuration procedure listed for BCM replacement. REFER to: Body Control Module (BCM) . |
| C1D22:11 | Steering Wheel Switch Right Module: Circuit Short To Ground | Refer to the appropriate Information and Entertainment System article for the procedure. |
| C1D22:23 | Steering Wheel Switch Right Module: Signal Stuck Low | Refer to the appropriate Information and Entertainment System article for the procedure. |
| C2003:11 | Steering Wheel Switch Left Module: Circuit Short To Ground | GO to Pinpoint Test AG |
| C2003:23 | Steering Wheel Switch Left Module: Signal Stuck Low | GO to Pinpoint Test AG |
| P1607:81 | MIL Output Circuit: Invalid Serial Data Received | This DTC sets when the IPC receives an invalid MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC P1607:81 returns, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1607:82 | MIL Output Circuit: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC does not receive an updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test BH If DTC P1607:82 returns without DTC U0100:00, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1607:87 | MIL Output Circuit: Missing Message | This DTC sets when the IPC does not receive updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test BH If DTC P1607:87 returns without DTC U0100:00, INSTALL a new PCM. Refer to the appropriate Engine article for the procedure. |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test AB |
| P1933:68 | Fuel Level Signal: Event Information | GO to Pinpoint Test C |
| U0073:00 | Control Module Communication Bus "A" Off: No Sub Type Information | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC. REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0074:00 | Control Module Communication Bus "B" Off: No Sub Type Information | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC. REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BH |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to Pinpoint Test BI |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BK |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BL |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BN |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BO |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BP |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test BQ |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module-Left: No Sub Type Information | GO to Pinpoint Test BR |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module-Right: No Sub Type Information | GO to Pinpoint Test BR |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BS |
| U0252:00 | Lost Communication With Lighting Control Module-Rear "B": No Sub Type Information | GO to Pinpoint Test BT |
| U0401:64 | Invalid Data Received From ECM/PCM A: Signal Plausibility Failure | This DTC sets when a message is temporarily undefined for more than 2 seconds from the PCM for the ambient temperature, fuel economy, engine coolant temperature or engine RPM data. CLEAR the DTC. REPEAT the self-test. If DTC U0401:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PCM. Refer to the appropriate Engine article for the procedure. |
| U0415:64 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Plausibility Failure | This DTC sets when the wheel rotation count message is temporarily undefined for more than 2 seconds from the ABS module for the odometer. CLEAR the DTC. REPEAT the self-test. If DTC U0415:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the ABS module. REFER to: Anti-Lock Brake System (ABS) And Stability Control . |
| U0422:00 | Invalid Data or Missing Data Received From Body Control Module: No Sub Type Information | This DTC sets when the fuel level, power mode or vehicle speed message are temporarily undefined for more than 2 seconds or if the TPMS status message is missing for more than 1, 250 milliseconds from the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0422:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM. REFER to: Body Control Module (BCM) . |
| U0422:68 | Invalid Data or Missing Data Received From Body Control Module: Event Information | This DTC sets when data is invalid from the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0422:68 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM. REFER to: Body Control Module (BCM) . |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This DTC sets when the temperature range data is invalid for more than 2 seconds from the HVAC module through the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0424:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the HVAC module. With DATC, REFER to: Climate Control System - Vehicles With: Dual Automatic Temperature Control (DATC) . With EMTC, REFER to: Climate Control System - Vehicles With: Electronic Manual Temperature Control (EMTC) . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC sets when data is invalid from the RCM. CLEAR the DTC. REPEAT the self-test. If DTC U0452:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the RCM. REFER to: Airbag Supplemental Restraint System (SRS) . |
| U053B:67 | Invalid Data Received From Image Processing Module A: Signal Incorrect After Event | This DTC sets when lane departure configuration data is missing from the IPMA. CLEAR the DTC. REPEAT the self-test. If DTC U0452:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the IPMA. REFER to: Lane Keeping System . |
| U053B:81 | Invalid Data Received From Image Processing Module A: Invalid Serial Data Received | This DTC sets when data is invalid from the IPMA. CLEAR the DTC. REPEAT the self-test. If DTC U0452:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the IPMA. REFER to: Lane Keeping System . |
| U053B:82 | Invalid Data Received From Image Processing Module A: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when data is invalid from the IPMA. CLEAR the DTC. REPEAT the self-test. If DTC U0452:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the IPMA. REFER to: Lane Keeping System . |
| U0558:00 | Invalid Data Received From Front Controls/Display Interface Module: No Sub Type Information | This DTC sets when data is invalid from the FCDIM for longer than 2 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0558:00 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the FCDIM. Refer to the appropriate Information and Entertainment System article for the procedure. |
| U201A:56 | Control Module Main Calibration Data: Invalid/Incompatible Configuration | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2101:01 | Control Module Configuration Incompatible: General Electrical Failure | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2108:42 | Adaptive Cruise Control: General Memory Failure | CLEAR the DTC. REPEAT the self-test. If DTC U2108:42 returns, |
| U2108:87 | Adaptive Cruise Control: Missing Message | GO to Pinpoint Test BU |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:41 returns, |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:44 returns, |
| U3006:16 | Control Module Input Power "A" Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test BV |
| U3006:17 | Control Module Input Power "A" Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test BW |