Instrumentation, Message Center And Warning Chimes DTCS: IPC
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor A Circuit: Circuit Short to Ground | GO to Pinpoint Test C . |
| P0460:13 | Fuel Level Sensor A Circuit: Circuit Open | GO to Pinpoint Test C . |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | DIAGNOSE all RCM DTCs. REFER to Supplemental Restraint System . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test AM . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub-Type Information | GO to Pinpoint Test BI . |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to Pinpoint Test BJ . |
| U0102:00 | Lost Communication With Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test BK . |
| U0121:00 | Lost Communication With ABS Control Module: No Sub Type Information | GO to Pinpoint Test BL . |
| U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test BM . |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BN . |
| U0137:00 | Lost Communication With Trailer Brake Control Module: No Sub Type Information | GO to Pinpoint Test BO . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BP . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BQ . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BR . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BS . |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BT . |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub-Type Information | This DTC sets when the IPC receives invalid odometer count, vehicle speed and engine temperature data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to Electronic Engine Controls . If no DTCs are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 | Invalid Data Received From ECM/PCM A: Invalid Serial Data Received | This DTC sets when the IPC receives invalid temperature and vehicle speed data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to Electronic Engine Controls . If no DTCs are present in the PCM, DIAGNOSE the observable symptom. |
| U0402:81 | Invalid Data Received from TCM: Invalid Serial Data Received | This DTC sets when the IPC receives invalid TCM data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM and other modules on the network. REFER to Electronic Engine Controls . If no DTCs are present in the PCM, DIAGNOSE the observable symptom. |
| U0415:56 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid trailer sway data from the ABS module. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub-Type Information | This DTC sets when the IPC receives invalid tire pressure data from the BCM. RETRIEVE and REPAIR all non-network DTCs in the BCM. REFER to Multifunction Electronic Modules . If no DTCs are present in the BCM, DIAGNOSE the observable symptom. |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid outside air temperature data from the HVAC module through the BCM. RETRIEVE and REPAIR all non-network DTCs in the HVAC module and BCM. REFER to Climate Control System General Information and Diagnostics . If no DTCs are present in the HVAC module or BCM, DIAGNOSE the observable symptom. |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid outside air temperature data from the HVAC module through the BCM. RETRIEVE and REPAIR all non-network DTCs in the HVAC module and BCM. REFER to Climate Control System General Information and Diagnostics . If no DTCs are present in the HVAC module or BCM, DIAGNOSE the observable symptom. |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BU . |
| U0438:56 | Invalid Data Received From Trailer Brake Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid trailer brake gain data from the Trailer Brake Module (TBM). CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U045A:56 | Invalid Data Received From Parking Assist Control Module "A": Invalid Incompatible Configuration | This DTC sets when the IPC receives invalid parking aid data from the PAM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U045A:81 | Invalid Data Received From Parking Assist Control Module "A": Invalid Serial Data Received | This DTC sets when the IPC receives invalid parking aid data from the PAM. RETRIEVE and REPAIR all non-network DTCs in the PAM. REFER to Parking Aid . If no DTCs are present in the PAM, DIAGNOSE the observable symptom. |
| U046B:86 | Invalid Data Received From Global Positioning System Module: Signal Invalid | This DTC sets when the IPC receives invalid compass data from the APIM.
NOTE:
The compass displays dashes (----) or is blank depending on the display mode. RETRIEVE and REPAIR all non-network DTCs in the BCM and APIM. Refer to the appropriate Information and Entertainment Systems article for the procedure. If no DTCs are present in the BCM and APIM, DIAGNOSE the observable symptom. |
| U0531:56 | Invalid Data Received From Rear Gate Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives rear liftgate data from the LTM when the IPC is not configured for rear liftgate or if the IPC does not receive expected liftgate data when it is configured for rear liftgate.
NOTE:
The IPC does not display the power liftgate settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0531:82 | Invalid Data Received From Rear Gate Module: Alive/ Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BV . |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/ Incompatible Configuration | This DTC sets when the IPC receives blind spot or side obstacle detection data when the IPC is not configured for BLIS ® or if the IPC does not receive blind spot or side obstacle detection data when it is configured for BLIS ®.
NOTE:
The IPC does not display the BLIS ® or CTA settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/ Sequence Counter Incorrect/Not Updated | This DTC sets in the IPC when the side obstacle detection data remains unchanged from the SOD-L through the BCM.
NOTE:
The IPC displays a fault warning message and does not display the check mark in the BLIS ® settings in the message center. RETRIEVE and REPAIR all non-network DTCs in the SOD-L and BCM. REFER to Side and Rear Vision . If no DTCs are present in the SOD-L and BCM, DIAGNOSE the observable symptom. |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/ Incompatible Configuration | This DTC sets when the IPC receives blind spot or side obstacle detection data when the IPC is not configured for BLIS ® or if the IPC does not receive blind spot or side obstacle detection data when it is configured for BLIS ®.
NOTE:
The IPC does not display the BLIS ® or CTA settings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets in the IPC when the side obstacle detection data remains unchanged from the SOD-R through the BCM.
NOTE:
The IPC displays a fault warning message and does not display the check mark in the BLIS ® settings in the message center. RETRIEVE and REPAIR all non-network DTCs in the SOD-R and BCM. REFER to Side and Rear Vision . If no DTCs are present in the SOD-R and BCM, DIAGNOSE the observable symptom. |
| U0545:56 | Invalid Data Received From Running Board Control Module: Invalid/ Incompatible Configuration | This DTC sets in the IPC if the configuration in the BCM for power running boards is incorrect.
NOTE:
The IPC does not display the running board setup menu and warnings in the message center. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0545:82 | Invalid Data Received From Running Board Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets in the IPC when the power running board data remains unchanged from the PRB module through the BCM.
NOTE:
The IPC does not display the running board setup menu and warnings in the message center. RETRIEVE and REPAIR all non-network DTCs in the PRB module and BCM. REFER to Exterior Trim and Ornamentation . If no DTCs are present in the PRB module or BCM, DIAGNOSE the observable symptom. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to Module Configuration , PMI for further information. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is retrieved again, |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is retrieved again, |
| U3000:43 | Control Module: Special Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:43 is retrieved again, |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:44 is retrieved again, |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:46 is retrieved again, |
| U3000:54 | Control Module: Missing Calibration | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:54 is retrieved again, |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BW . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BX . |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets on-demand and in continuous memory when the IPC detects a messaged START input for 15 seconds or more. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. REFER to Steering Column Switches to diagnose the ignition start circuit to the BCM. |