| B108A:12 |
Start Button: Circuit Short To Battery |
REFER to
Steering Column Switches
. |
| B10AB:06 |
Remote Keyless Entry Synchronization: Algorithm Based Failure |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| B10C7:01 |
Interior Trunk Antenna: General Electrical Failure |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10C8:01 |
Interior Centre Antenna: General Electrical Failure |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10C9:01 |
Interior Front Antenna: General Electrical Failure |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D7:05 |
PATS Key: System Programming Failure |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D7:31 |
PATS Key: No Signal |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D8:51 |
PATS Key Less Than Minimum Programmed: Not Programmed |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D9:11 |
PATS Transponder: Circuit Short To Ground |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D9:12 |
PATS Transponder: Circuit Short To Battery |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D9:31 |
PATS Transponder: No Signal |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10D9:87 |
PATS Transponder: Missing Message |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10DA:51 |
PATS Target Identifier: Not Programmed |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B10DA:61 |
PATS Target Identifier: Signal Calculation Failure |
REFER to
Anti-Theft Passive Anti-Theft System (PATS)
. |
| B11CA:01 |
Driver Door External Antenna: General Electrical Failure |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| B121A:11 |
Keypad Illumination Output: Circuit Short To Ground |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| B121A:15 |
Keypad Illumination Output: Circuit Short To Battery or Open |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| B121B:11 |
Keypad Input Switch: Circuit Short To Ground |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| P1571:12 |
Brake Switch: Circuit Short To Battery |
REFER to
Exterior Lighting
. |
| U0140:87 |
Lost Communication With Body Control Module: Missing Message |
GO to Pinpoint Test D |
| U1000:00 |
Solid State Driver Protection Active - Driver Disabled: No Sub Type Information |
GO to Pinpoint Test M |
| U201F:31 |
External Receiver: No Signal |
REFER to
Handles, Locks, Latches and Entry Systems
. |
| U201F:56 |
External Receiver: Invalid/Incompatible Configuration |
CARRY OUT the PMI procedure as directed by the scan tool (
Module Configuration
, PMI for further information). CLEAR the DTCs. REPEAT the self-test. If DTC U201F:56 is retrieved again, INSTALL a new RFA. REFER to Remote Function Actuator (RFA) Module
. |
| U2100:55 |
Initial Configuration Not Complete: Not Configured |
CARRY OUT the PMI procedure as directed by the scan tool (
Module Configuration
, PMI for further information). CLEAR the DTCs. REPEAT the self-test. If DTC U2100:55 is retrieved again, INSTALL a new RFA. REFER to Remote Function Actuator (RFA) Module
. |
| U3000:49 |
Control Module: Internal Electronic Failure |
DIAGNOSE all other DTCs first. If no other DTCs are present, INSTALL a new RFA module. REFER to Remote Function Actuator (RFA) Module
. |
| U3003:62 |
Battery Voltage: Signal Compare Failure |
GO to Pinpoint Test J |