Vehicle Dynamic Suspension DTCS
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| C110C:11 | Left Front Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110C:12 | Left Front Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110C:13 | Left Front Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110D:11 | Right Front Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110D:12 | Right Front Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110D:13 | Right Front Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110E:11 | Left Rear Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110E:12 | Left Rear Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110E:13 | Left Rear Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110F:11 | Right Rear Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110F:12 | Right Rear Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110F:13 | Right Rear Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C1124:55 | Height Sensor(s): Not Configured | This DTC is automatically set in a new VDM and indicates that the system requires height sensor calibration. Once the system is calibrated, the DTC can be cleared. CALIBRATE the VDM and sensors. FOLLOW the diagnostic scan tool instructions. CLEAR the DTC. REPEAT the VDM self-test. |
| C1A03:11 | Left Front Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A03:12 | Left Front Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A04:11 | Right Front Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A04:12 | Right Front Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A05:11 | Left Rear Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A05:12 | Left Rear Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A06:11 | Right Rear Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A06:12 | Right Rear Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| P1758:19 | Pressure Solenoid Control System Incorrect Current: Circuit Current Above Threshold | GO to Pinpoint Test C . |
| U0001:88 | High Speed CAN Communications Bus: Bus Off | A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC. REPEAT the Network Test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network for schematic and connector information. |
| U0100:87 | Lost Communication with ECM / PCM "A": Missing Message | GO to Pinpoint Test F . |
| U0121:87 | Lost Communication with Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test G . |
| U0126:87 | Lost Communication with Steering Angle Sensor Module: Missing Message | GO to Pinpoint Test H . |
| U0140:87 | Lost Communication with Body Control Module: Missing Message | GO to Pinpoint Test I . |
| U0151:87 | Lost Communication with Restraints Control Module: Missing Message | GO to Pinpoint Test J . |
| U0155:87 | Lost Communication with Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test K . |
| U0253:87 | Lost Communication with Accessory Protocol Interface Module: Missing Message | CHECK the service history for recent service actions related to the VDM. This DTC sets due to incomplete or improper PMI procedures. If there have been recent service actions with the VDM, REPEAT the PMI procedure as directed by the diagnostic scan tool. CLEAR the DTC and CARRY OUT the VDM self-test. If the DTC does not return, the repair is complete. If the DTC returns, INSTALL a new VDM to correct the failure to retain the software data. REFER to Vehicle Dynamics Module (VDM) . |
| U0401:00 | Invalid Data Received from ECM / PCM "A": No Sub Type Information | GO to Pinpoint Test F . |
| U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test G . |
| U0428:00 | Invalid Data Received from Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test H . |
| U0452:00 | Invalid Data Received from Restraints Control Module: No Sub Type Information | GO to Pinpoint Test J . |
| U200D:11 | Control Module Output Power A: Circuit Short to Ground | GO to Pinpoint Test E . |
| U200D:12 | Control Module Output Power A: Circuit Short to Battery | GO to Pinpoint Test E . |
| U200E:11 | Control Module Output Power B: Circuit Short to Ground | GO to Pinpoint Test E . |
| U200E:12 | Control Module Output Power B: Circuit Short to Battery | GO to Pinpoint Test E . |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | This DTC sets due to incomplete or improper flash programming procedures. REPEAT the flash programming procedure as directed by the diagnostic scan tool. CLEAR the DTC and CARRY OUT the VDM self-test. If the DTC does not return, the repair is complete. If the DTC returns, INSTALL a new VDM to correct the failure to retain the software data. REFER to Vehicle Dynamics Module (VDM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC is pre-set in a new VDM and clears automatically when the VDM is configured correctly. CONNECT the diagnostic scan tool and CARRY OUT the PMI procedure as directed by the diagnostic scan tool. CLEAR the DTC and CARRY OUT the VDM self-test. If the DTC does not return, the repair is complete. If the DTC returns, INSTALL a new VDM to correct the failure to retain the configuration data. REFER to Vehicle Dynamics Module (VDM) . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the DTC. CARRY OUT the VDM module self-test. RETRIEVE and RECORD all Diagnostic Trouble Codes (DTCs). If the DTC returns, INSTALL a new VDM. REFER to Vehicle Dynamics Module (VDM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test B . |