LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2017 >> Explorer Platinum >> Repair and Diagnosis >> Brakes >> Traction Control >> Anti-Lock Brake System Component Testing >> Pinpoint Tests >> Pinpoint Tests BA: SASM Communication Concern With GWM >> Possible Causes
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Possible Causes

  1. BA1: CHECK THE COMMUNICATION NETWORK 
    • Ignition ON, engine OFF.
    • Press the Read Vehicle Information button to view the results of the modules communicating on the network.
    • Retrieve the continuous memory DTCs.
    • Does the GWM pass the Network Test? 
      Yes No
      Go to  BA2. DIAGNOSE the scan tool does not communicate with the GWM. REFER to COMMUNICATIONS NETWORK .
  2. BA2: RECHECK THE SASM FOR THE LOST COMMUNICATION DTC 
    • Clear the SASM DTCs.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Carry out the SASM self-test.
    • Is DTC U0146:xx still present? 
      Yes No
      Go to  BA3. The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.
  3. BA3: REVIEW THE SASM SELF-TEST FOR VOLTAGE-REALTED DTCS 
    • Review the results from the SASM self-test.
    • Is DTC U3003:1C or U3003:17 present? 
      Yes No
      For DTC U3003:1C, Go to PINPOINT TEST BD .
      For DTC U3003:17, Go to PINPOINT TEST BE .
      For all others,
      No fault found.      		 Go to  BA4.
  4. BA4: CHECK FOR GWM DTCS 
  5. BA5: CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN 
    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.
    • Check the vehicle service history for recent service actions related to the GWM or SASM. If recent service history is found:
      • Verify the correct replacement module was installed. HVBOM may be used to verify correct part fitment.
      • Verify the configuration of replacement module was correct. Re-configure the module using as-built data if prior configuration is suspect.
      • Verify the module was not obtained from a like vehicle and installed into customer vehicle. Return the swapped module to source vehicle and obtain new replacement module.
    • Operate the system and determine if the observable symptom is still present.
    • Is the observable symptom still present? 
      Yes No
      Go to  BA6. The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.
  6. BA6: CHECK FOR COMMUNICATION DTCS IN OTHER MODULES 
    • Ignition ON, engine OFF.
    • Retrieve the continuous memory DTCs.
    • Is DTC U0146:xx set in 1 or more modules in addition to the SASM? 
      Yes No
      Go to  BA7. Go to  BA8.
  7. BA7: VERIFY GWM OPERATION 
    • Ignition OFF.
    • GWM connector disconnected.
    • SASM connector disconnected.
    • Disconnect all in-line electrical connectors between the SASM and the GWM.
    • Using a good light source, inspect all disconnected electrical connectors for the following:
      • corrosion - install new connector or terminal and clean the module pins
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Connect all in-line electrical connectors between the SASM and the GWM. Make sure the connectors seat and latch correctly.
    • SASM connector connected. Make sure the connector seats and latches correctly.
    • GWM connector connected. Make sure the connector seats and latches correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
      Yes No
      INSTALL a new GWM.
      CHECK OASIS for any applicable Technical Service Bulletins TSBs.
      If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions.
      If no TSBs address this concern, INSTALL a new GWM. REFER to COMMUNICATIONS NETWORK .      		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
      If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form.
  8. BA8: VERIFY SASM OPERATION 
    • Ignition OFF.
    • SASM connector disconnected.
    • GWM connector disconnected.
    • Disconnect all in-line electrical connectors between the SASM and the GWM.
    • Using a good light source, inspect all disconnected electrical connectors for the following:
      • corrosion - install new connector or terminal and clean the module pins
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Connect all in-line electrical connectors between the SASM and the GWM. Make sure the connectors seat and latch correctly.
    • GWM connector connected. Make sure the connector seats and latches correctly.
    • SASM connector connected. Make sure the connector seats and latches correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
      Yes No
      INSTALL a new SASM.
      CHECK OASIS for any applicable TSBs.
      If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions.
      If no TSBs address this concern, INSTALL a new SASM-clockspring assembly. REFER to CLOCKSPRING .      		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
      If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form.
scientia non olet · About LEMON Manuals