| P0460:11 |
Fuel Level Sensor "A" Circuit: Circuit Short To Ground |
GO to Pinpoint Test C |
| P0460:13 |
Fuel Level Sensor "A" Circuit: Circuit Open |
GO to Pinpoint Test C |
| P0483:00 |
Fan Performance: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC P0483:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| P060C:00 |
Internal Control Module Main Processor Performance: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC P060C:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U0029:00 |
Vehicle Communication Bus "A" Performance: No Sub Type Information |
This DTC can set due to high network traffic or intermittent CAN concerns. DIAGNOSE all symptoms and other Diagnostic Trouble Codes (DTCs) set in the IPC. If no other symptoms or Diagnostic Trouble Codes (DTCs) are present, DISREGARD this DTC if set. |
| U0030:13 |
Vehicle Communication Bus "A" (+) Open: Circuit Open |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0031:11 |
Vehicle Communication Bus "A" (+) Low: Circuit Short To Ground |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0032:12 |
Vehicle Communication Bus "A" (+) High: Circuit Short To Battery |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0033:13 |
Vehicle Communication Bus "A" (-) Open: Circuit Open |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0034:11 |
Vehicle Communication Bus "A" (-) Low: Circuit Short To Ground |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0035:12 |
Vehicle Communication Bus "A" (-) High: Circuit Short To Battery |
DIAGNOSE the CAN. REFER to: Communications Network
. |
| U0073:00 |
Control Module Communication Bus "A" Off: No Sub Type Information |
A HS-CAN fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC. REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to Module Communications Network
for schematic and connector information. |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test AW |
| U0101:00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test AX |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AY |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
This DTC sets when the IPC receives invalid data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to: Electronic Engine Controls
. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U1A00:00 |
Private Communication Network: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U1A00:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U1A4B:00 |
Control Module Processor B: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U1A4B:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200A:01 |
Control Module Internal Power A: General Electrical Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200A:01 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200A:02 |
Control Module Internal Power A: General Signal Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200A:02 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200B:01 |
Control Module Internal Power B: General Electrical Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200B:01 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200B:02 |
Control Module Internal Power B: General Signal Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200B:02 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200B:11 |
Control Module Internal Power B: Circuit Short To Ground |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200B:11 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200B:12 |
Control Module Internal Power B: Circuit Short To Battery |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200B:12 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:01 |
Control Module Internal Power C: General Electrical Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:01 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:02 |
Control Module Internal Power C: General Signal Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:02 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:11 |
Control Module Internal Power C: Circuit Short To Ground |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:11 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:12 |
Control Module Internal Power C: Circuit Short To Battery |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:12 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:21 |
Control Module Internal Power C: Signal Amplitude < Minimum |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:21 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:22 |
Control Module Internal Power C: Signal Amplitude > Maximum |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:22 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:31 |
Control Module Internal Power C: No Signal |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:31 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:32 |
Control Module Internal Power C: Signal Low Time < Minimum |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:32 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:41 |
Control Module Internal Power C: General Checksum Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:41 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U200C:42 |
Control Module Internal Power C: General Memory Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U200C:42 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U2014:01 |
Control Module Hardware: General Electrical Failure |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2014:01 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U2015:00 |
Control Module Boot Software: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2015:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U2016:00 |
Control Module Main Software: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2016:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U2017:00 |
Control Module Software #2: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2017:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U2018:00 |
Control Module Software #3: No Sub Type Information |
CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2018:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC)
. |
| U201A:00 |
Control Module Main Calibration Data: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure using As-Built data as directed by the scan tool. REFER to: Module Programming
. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure using As-Built data as directed by the scan tool. REFER to: Module Programming
. If there have been no recent service actions, INSTALL a new IPC to correct the failure to retain configuration data. REFER to: Instrument Panel Cluster (IPC)
. |
| U3000:46 |
Control Module: Calibration/Parameter Memory Failure |
CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure using As-Built data as directed by the scan tool. REFER to: Module Programming
. If there have been no recent service actions, INSTALL a new IPC to correct the failure to retain configuration data. REFER to: Instrument Panel Cluster (IPC)
. |
| U3003:01 |
Battery Voltage: General Electrical Failure |
GO to Pinpoint Test AZ |