LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2017 >> Transit Connect Titanium >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Diagnosis And Testing >> Direct Clutch Assembly
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Direct Clutch Assembly

Direct Clutch 

For direct (3, 5, R) clutch operation, REFER to: Transmission Description . Refer to: Forward Clutch Assembly .

Direct Clutch 

Condition Possible Sources Action
Direct (3, 5, R) clutch does not apply SSB Solenoid filter blocked CLEAN or INSTALL a new solenoid. Refer to: Solenoid .
SSB is mechanically stuck OFF INSTALL a new solenoid. Refer to: Solenoid .
Direct (3, 5, R) clutch regulator valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch regulator valve. Refer to: Main Control Valve Body . If bore or valve is damaged, INSTALL a new main control valve body.
SSB SIG, C35R, C35R SUP hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. Refer to: Main Control Valve Body .
REV SUPPLY/DRIVE 2 to C35R SUP check ball missing/damaged REMOVE the main control valve body, and INSPECT the check ball missing/damage. Refer to: Main Control Valve Body .
C35R supply hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission cover and support tower passages for debris/blockage. CLEAN as necessary. Refer to: Transmission .
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for wear and damage. INSTALL new components necessary. Refer to: Transmission .
Direct (3, 5, R) clutch friction plates DISASSEMBLE and INSPECT the direct (3, 5, R) clutch friction and steel plates. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch piston seal leakage INSTALL a new direct (3, 5, R) clutch piston and seals. Refer to: Transmission .
Direct (3, 5, R) clutch always applied SSB O-rings damaged/leaking INSTALL a new solenoid. Refer to: Solenoid .
SSB mechanically stuck ON INSTALL a new solenoid. Refer to: Solenoid .
Direct (3, 5, R) clutch regulator valve stuck ON DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch regulator valve and bias spring. If bore or valve is damaged, INSTALL a new main control valve body. Refer to: Main Control Valve Body .
SSB SIG, C35R, C35R SUP hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control and separator plate passages for leakage. CLEAN as necessary. Refer to: Main Control Valve Body .
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for damage that would prevent free rotation. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch friction plates DISASSEMBLE and INSPECT the direct (3, 5, R) clutch friction and steel plates. Measure clutch pack clearance. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch piston return spring INSPECT the return spring for damage. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch delayed/soft/slipping apply Incorrect Transmission Strategy programmed into PCM Remove SSB and record solenoid band number. Refer to: Solenoid . Using the scan tool, verify the correct band number is stored in the PCM. If bands numbers do not match, INSTALL a new SSB with correct band number.
SSB solenoid filter partially blocked or restricted INSTALL a new solenoid. Refer to: Solenoid .
SSB mechanically sticking INSTALL a new solenoid. Refer to: Solenoid .
Direct (3, 5, R) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control valve body. Refer to: Main Control Valve Body .
Direct (3, 5, R) clutch boost valve stuck ON DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch boost valve and bias spring. If bore, valve or spring is damaged, INSTALL a new main control. Refer to: Main Control Valve Body .
SSB SIG, C35R, C35R SUP hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. Refer to: Main Control Valve Body .
REV SUPPLY/DRIVE 2 to C35R SUP check ball missing/damaged REMOVE the main control valve body and INSPECT the check ball missing/damage. Refer to: Main Control Valve Body .
C35R supply hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission cover and support tower passages for debris/blockage. CLEAN as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch friction plates DISASSEMBLE and INSPECT the direct (3, 5, R) clutch friction and steel plates. Measure clutch pack clearance. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch piston seal leakage INSTALL a new direct (3, 5, R) clutch piston and seals. Refer to: Transmission .
Direct (3, 5, R) clutch harsh apply Incorrect Transmission Strategy programmed into PCM Remove SSB and record solenoid band number. Refer to: Solenoid . Using the scan tool, verify the correct band number is stored in the PCM. If bands numbers do not match, INSTALL a new SSB with correct band number.
SSB mechanically sticking INSTALL a new solenoid. Refer to: Solenoid .
Direct (3, 5, R) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch regulator valve and bias spring. If bore, valve or spring is damaged, INSTALL a new main control valve body. Refer to: Main Control Valve Body .
Direct (3, 5, R) clutch boost valve sticking DISASSEMBLE, CLEAN and INSPECT the direct (3, 5, R) clutch boost valve and bias spring. If bore, valve or spring is damaged, INSTALL a new main control valve body. Refer to: Main Control Valve Body .
SSB SIG, C35R, C35R SUP hydraulic circuits blocked/leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. Refer to: Main Control Valve Body .
Direct (3, 5, R) clutch friction plates DISASSEMBLE and INSPECT the direct (3, 5, R) clutch friction and steel plates. INSTALL new components as necessary. Refer to: Transmission .
Direct (3, 5, R) clutch piston return spring INSPECT the return spring for proper installation and damage. INSTALL new components as necessary. Refer to: Transmission .