Am/Fm/Cd/Sync/Touchscreen Display: FCIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B13DC-11 | Compact Disc Slot Illumination: Circuit Short To Ground | REFER to: Instrument Panel and Interior Switches Illumination . See DTC Chart: FCIM |
| B13DC-12 | Compact Disc Slot Illumination: Circuit Short To Battery | REFER to: Instrument Panel and Interior Switches Illumination . See DTC Chart: FCIM |
| B13DC-13 | Compact Disc Slot Illumination: Circuit Open | REFER to: Instrument Panel and Interior Switches Illumination . See DTC Chart: FCIM |
| U0009:88 (Sony ® FCIM only) | High Speed CAN Communication Bus (-) Shorted to Bus (+): Bus off | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. |
| U0155:00 (Sony ® FCIM only) | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0155:87 (Non-branded FCIM only) | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test AN |
| U0257:00 (Sony ® FCIM only) | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM. GO to Pinpoint Test AU |
| U0257:87 (Non-branded FCIM only) | Lost Communication With Front Controls / Display Interface Module: Missing Message |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM GO to Pinpoint Test AV |
| U0423:00 (Sony ® FCIM only) | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. REFER to: Instrumentation, Message Center and Warning Chimes . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U2013:63 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U201A:51 (Non-branded FCIM only) | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . See Programmable Module Installation (PMI). If there have been no recent service actions, INSTALL a new FCIM to correct the failure to retain configuration data. REFER to: Front Controls Interface Module (FCIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AW |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AX |