Common Specifications & Procedures

EDGE COMMON SPECIFICATIONS & PROCEDURES

System			Specifications/Procedures
Air Conditioning
Service			SPECIFICATIONS
Torque			SPECIFICATIONS
Axle Nut/Hub Nut
Front			148 lb.ft (200 Nm)
Rear
	AWD		148 lb.ft (200 Nm)
	FWD		148 lb.ft (200 Nm)
Battery			SPECIFICATIONS
Brakes
Bleeding Sequence			BRAKE SYSTEM PRESSURE BLEEDING
Front Disc Brakes w/Torque			FRONT DISC BRAKE
Rear Disc Brakes w/Torque			REAR DISC BRAKE
Charging
Generator w/Torque
	2.0L EcoBoost (184kW/250PS) - MI4		Upper Generator Bolt: 18 lb.ft (25 Nm) Lower Generator Bolts: 18 lb.ft (25 Nm)
	2.7L EcoBoost (238kW/324PS)		Generator Bolt and Stud Nut: 35 lb.ft (47 Nm)
	3.5L Duratec (212kW/278PS)		Generator Stud Nut: 35 lb.ft (47 Nm) Generator Stud Bolt: 71 lb.in (8 Nm) Generator and Bolt: 35 lb.ft (47 Nm)
Drive Belts
Adjustment
		2.0L ECOBOOST (184KW/250PS) - MI4	ACCESSORY DRIVE
		2.7L EcoBoost (238kW/324PS)	ACCESSORY DRIVE
		3.5L Duratec (212kW/278PS)	ACCESSORY DRIVE
Belt Routing
	2.0L ECOBOOST (184KW/250PS) - MI4		ACCESSORY DRIVE - COMPONENT LOCATION
	2.7L EcoBoost (238kW/324PS)		ACCESSORY DRIVE - COMPONENT LOCATION
	3.5L Duratec (212kW/278PS)		ACCESSORY DRIVE - COMPONENT LOCATION
Engine Cooling
General Service Specifications
	2.0L ECOBOOST (184KW/250PS) - MI4		SPECIFICATIONS
	2.7L EcoBoost (238kW/324PS)		SPECIFICATIONS
	3.5L Duratec (212kW/278PS)		SPECIFICATIONS
Radiator Cap Pressure			145 kPa (21 psi)
Thermostat R & I
	2.0L GDTI		THERMOSTAT HOUSING
	2.7L		THERMOSTAT
	3.5L		THERMOSTAT HOUSING
Water Pump R & I
	2.0L GDTI		COOLANT PUMP
	2.7L		COOLANT PUMP
	3.5L		COOLANT PUMP
Engine Mechanical
2.0L GDTI
	Compression		SPECIFICATIONS
	Oil Pressure (Hot @ 2000 RPM)		29-60 psi (200-414 kPa)
	Overhaul		SPECIFICATIONS
	Torque		SPECIFICATIONS
2.7L
Compression			SPECIFICATIONS
Oil Pressure Reading 1 (Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park.)			21 psi (144.8 kPa)
		Oil Pressure Reading 2 (Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected))	Reading 1 value plus 8 psi (55.1 kPa)
Overhaul			SPECIFICATIONS
Torque			SPECIFICATIONS
3.5L
	Compression		SPECIFICATIONS
	Oil Pressure (@ 1, 500 RPM with engine at normal operating temperature.)		30.0psi (206.8kPa)
	Overhaul		SPECIFICATIONS
	Torque		SPECIFICATIONS
Fluid Specifications			See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
2.0L GDTI			Stage 1: 50 Nm (37 lb-ft). Stage 2: 80 Nm (59 lb-ft). Stage 3: 112 Nm (83 lb-ft).
2.7L			59 lb.ft (80 Nm)
3.5L			59 lb.ft (80 Nm)
Fuel System
Fuel Filter Location			Located in fuel tank as part of Fuel Pump Module.
Fuel Filter R & I
	2.0L GDTI		FUEL PUMP AND SENDER UNIT
	2.7L		FUEL PUMP AND SENDER UNIT
	3.5L		FUEL PUMP AND SENDER UNIT
Pressure Release Procedure
	2.0L GDTI		FUEL SYSTEM PRESSURE RELEASE
	2.7L		FUEL SYSTEM PRESSURE RELEASE
	3.5L		FUEL SYSTEM PRESSURE RELEASE
Pressure Specification
	2.0L GDTI		SPECIFICATIONS
	2.7L		SPECIFICATIONS
	3.5L		SPECIFICATIONS
	Fuel Pressure Test Procedure
	2.0L GDTI		FUEL SYSTEM PRESSURE CHECK
	2.7L		FUEL SYSTEM PRESSURE CHECK
	3.5L		FUEL SYSTEM PRESSURE CHECK
Ignition
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Routing)			Engines are equipped with Coil-on-plug ignition.
Spark Plugs
2.0L GTDI
	Type		CYFS 12Y PCT
	Gap		.031 In. (0.8 mm)
	Torque		106 In. Lbs. (12 N.m)
2.7L
Type			CYFS 12Y PT
Gap			0.028-0.031 in (0.7-0.8 mm)
Torque			133 In. Lbs. (15 N.m)
3.5L
Type			Motorcraft CYFS12F-5
Gap			.049-.053 In. (1.25-1.35 mm)
Torque			133 In. Lbs. (15 N.m)
Starting
Starter
	2.0L		SPECIFICATIONS
	2.7L		SPECIFICATIONS
	3.5L		SPECIFICATIONS
Torque
	2.0L		STARTER MOTOR
	2.7L		STARTER MOTOR
	3.5L		STARTER MOTOR
Wheel Alignment
Adjustment Specifications			SPECIFICATIONS
Torque			TORQUE SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque			: 162 lb.ft (220 Nm)