Adaptive Cruise Control: CCM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| C0072:00 | Brake Temperature Too High: No Sub Type Information | REFER to: Anti-Lock Brake System (ABS) and Stability Control . |
| C1132:4B | Head Up Display: Over Temperature | REFER to: Collision Warning and Collision Avoidance System . |
| C1A67:54 | Forward Looking Sensor: Missing Calibration | This DTC will set if CCM factory alignment process failed, or if the CCM reports alignment angle is out of range (0 to 5 degrees). The adaptive cruise control system will be disabled and a malfunction message will display in the message center if the system is activated. PERFORM the horizontal alignment procedure. REFER to: Cruise Control Radar Alignment . |
| C1A67:76 | Forward Looking Sensor: Wrong Mounting Position | This DTC will set if vertical alignment relative to the ground during factory alignment is out of range (-1.5 to 1.5 degrees). The adaptive cruise control system will be disabled and a malfunction message will display in the message center if the system is activated. This DTC can only be set during factory alignment. |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | GO to Pinpoint Test E |
| C1A67:97 | Forward Looking Sensor: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test F |
| C1A67:98 | Forward Looking Sensor: Component or System Over Temperature | The CCM was over-temperature. This may occur during extended use in extremely high weather temperatures. The adaptive cruise control system operation resumes after the CCM cools. |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | REFER to: Communications Network . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test G |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test C |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test H |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test I |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test J |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | GO to Pinpoint Test K |
| U0300:55 | Internal Control Module Software Incompatibility: Not Configured | This DTC sets when the CCM configuration has not been completed. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . |
| U0401:68 | Invalid Data Received From ECM/PCM "A": Event Information | This DTC sets when the CCM receives invalid network data from the PCM with a faulted Vehicle Speed Sensor (VSS) signal, Accelerator Pedal Position (APP) sensor signal, gear position, or cruise control switch input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0418:68 | Invalid Data Received From Brake System Control Module: Event Information | This DTC sets when the CCM receives invalid network data from the ABS module with a faulted brake signal input, yaw rate input, steering wheel angle input or vehicle speed input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | This DTC sets when the CCM receives invalid network data from the RCM with a faulted yaw rate input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Cruise Control Module (CCM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets when the CCM configuration has not been completed. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets when the CCM configuration has not been completed. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:44 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) . |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:49 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) . |
| U3000:63 | Control Module: Circuit/Component Protection Time-Out | GO to Pinpoint Test L |
| U3000:66 | Control Module: Signal Has Too Many Transitions/Events | This DTC sets in the CCM if the module receives invalid network data. CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test M |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test N |