LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2018 >> Focus ST >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Abs Guided Routine Testing >> Pinpoint Tests >> Pinpoint Test LB: Steering Wheel Position Sensor Faults
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test LB: Steering Wheel Position Sensor Faults

  1. LB1: CHECK FOR DTCS IN OTHER MODULES 
    • Ignition ON, engine OFF.
    • Retrieve the continuous memory DTCs.
    • Record any ABS module DTCs.
    • Are there are DTCs present in the PSCM, RCM or SCCM? 
    Yes No
    DIAGNOSE all other module DTCs before diagnosing ABS module DTCs C0051:xx.
    For PSCM DTCs, REFER to POWER STEERING
    For RCM DTCs, REFER to AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .
    For SCCM DTCs, REFER to STEERING WHEEL AND COLUMN ELECTRICAL COMPONENTS    		 Go to  LB2.
  2. LB2: CHECK THE ABS MODULE DTCS 
    • Review the ABS module DTCs recorded in the previous step.
    • Are any communication (U-Codes) or wheel speed sensor DTCs present in the ABS module? 
    Yes No
    DIAGNOSE all ABS module communication (U-Code) and wheel speed sensor DTCs before diagnosing any C0051:xx DTCs. GO to the ABS - ANTILOCK BRAKING SYSTEM DTC INDEX . Go to  LB3.
  3. LB3: VERIFY STABILITY CONTROL SENSOR CALIBRATION 
    • Using a diagnostic scan tool, carry out the IVD Initialization routine. Follow the diagnostic scan tool directions.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Test drive the vehicle above 12 km/h (7 mph) and make at least one left turn and one right turn.
    • Carry out the ABS self-test.
    • Are any DTCs listed in the Fault Trigger Conditions Table present? 
    Yes No
    For F-Super Duty, Go to  LB4.
    For vehicles equipped with active park assist, Go to  LB4.
    For all others, Go to  LB6.    		 The condition causing the concern is no longer present. The concern was most likely due to an incomplete calibration or a failed calibration of the stability control sensors.
  4. LB4: CHECK THE SCCM STEERING WHEEL ANGLE PID 
    • Start the engine.
    • Access the SCCM and monitor the SW_ANGLE (ANGL) PID.
    • Monitor the PID while slowly turning the steering wheel one complete revolution to the left and then to the right.
    • Does the PID display increase smoothly by 1.5 degrees and display a complete 360 degree rotation? 
    Yes No
    Go to  LB6. Go to  LB5.
  5. LB5: CENTER THE STEERING WHEEL ROTATION SENSOR 
    • Ignition OFF.
    • Center the clockspring and steering wheel rotation sensor. Refer to the CLOCKSPRING ADJUSTMENT .
    • Test drive the vehicle at speeds greater than 20 km/h (12 mph) and make at least 1 left turn and 1 right turn.
    • Carry out the ABS self-test.
    • Are any DTCs listed in the Fault Trigger Conditions Table present? 
    Yes No
    INSTALL a new steering wheel rotation sensor.
    REFER to REMOVAL AND INSTALLATION    		 The concern is not present or cannot be recreated at this time. The DTC may have been set due to an off center steering wheel rotation sensor.
  6. LB6: CHECK THE ABS MODULE WHEEL SPEED SENSOR PIDS 
    • Ignition ON, engine OFF.
    • Access the ABS and monitor the LF_WSPD (SPD) PID.
    • Access the ABS and monitor the LR_WSPD (SPD) PID.
    • Access the ABS and monitor the RF_WSPD (SPD) PID.
    • Access the ABS and monitor the RR_WSPD (SPD) PID.
    • Are the wheel speed PIDs within 5 km/h (3 mph) of each other and the vehicle speed as indicated on the speedometer? 
    Yes No
    Go to  LB7. INSTALL a new WSS.
    INSTALL a new wheel speed sensor for any sensor not matching the others or the speedometer. REFER to REMOVAL AND INSTALLATION
  7. LB7: CHECK THE ABS MODULE YAW RATE VALUE PID 
    NOTE: The vehicle must be on level ground and at a complete standstill. Any vehicle movement results in false values for this test.
    • Access the ABS and monitor the YAW_RATE (ANGV) PID.
    • Is the PID value between -0.05 and 0.05? 
    Yes No
    Go to  LB8. Go to  LB11.
  8. LB8: CHECK THE ABS MODULE LATERAL ACCELERATION PID 
    NOTE: The vehicle must be on level ground and at a complete standstill. Any vehicle movement results in false values for this test.
    • Access the ABS and monitor the LAT_ACCL (ACC) PID.
    • Is the PID value between -0.4 and 0.4? 
    Yes No
    Go to  LB9. Go to  LB11.
  9. LB9: CHECK THE ABS MODULE LONGITUDINAL ACCELERATION SENSOR PID 
    NOTE: The vehicle must be on level ground and at a complete standstill. Any vehicle movement results in false values for this test.
    • Access the ABS and monitor the LONG_ACCL (ACC) PID.
    • Is the PID value between -0.4 and 0.4? 
    Yes No
    Go to  LB10. Go to  LB11.
  10. LB10: CHECK THE ABS MODULE ROLL RATE PID 
    NOTE: The vehicle must be on level ground and at a complete standstill. Any vehicle movement results in false values for this test.
    • Access the ABS and monitor the ROLL_RATE (ANGV) PID.
    • Is the PID value between -0.4 and 0.4? 
    Yes No
    For F-Super Duty, Go to  LB13.
    For vehicles equipped with active park assist, Go to  LB13.
    For all others, Go to  LB14.    		 Go to  LB11.
  11. LB11: CHECK THE RCM INSTALLATION AND MOUNTING SURFACE 
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Ignition OFF.
    • Wait one minute.
    • RCM_A connector disconnected.
    • RCM_B connector disconnected.
    • Inspect the RCM installation and make sure the fasteners are fully seated and tightened to specifications. REFER to REMOVAL AND INSTALLATION
    • Inspect the RCM mounting surface for damage, corrosion or dirt.
    • Is the RCM installed correctly and is the mounting surface clean and free from damage? 
    Yes No
    Go to  LB12. CLEAN or REPAIR the mounting surface or REINSTALL the RCM as necessary. REFER to REMOVAL AND INSTALLATION
  12. LB12: CHECK FOR CORRECT RCM OPERATION 
    • Inspect and repair all disconnected electrical connectors for the following:
      • inspect the connectors (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect the wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B CPA lever-lock for correct operation. Refer to RCM removal and installation in REMOVAL AND INSTALLATION
      • repair any concerns found. Refer to OEM CONNECTOR REPAIR PROCEDURES (EXCEPT ELECTRIC) for schematic and connector information.
    • RCM_B connector connected. Make sure the connector seats and latches correctly.
    • RCM_A connector connected. Make sure the connector seats and latches correctly.
    • Test drive the vehicle at speeds greater than 20 km/h (12 mph) and make at least 1 left turn and 1 right turn.
    • Carry out the ABS self-test.
    • Are any DTCs listed in the Fault Trigger Conditions Table present? 
    Yes No
    INSTALL a new RCM.
    CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA.
    If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions.
    If no service articles address this concern, INSTALL a new RCM. REFER to RESTRAINTS CONTROL MODULE (RCM)
    ORDER a replacement RCM and INCLUDE the RVC on the form.
    If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form.    		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector, high network traffic or an intermittent fault condition. ADDRESS the root cause of any connector or pin issues.
  13. LB13: CHECK FOR CORRECT STEERING WHEEL ROTATION SENSOR OPERATION 
    • Ignition OFF.
    • ABS Module connector disconnected.
    • RCM_A connector disconnected. (if not previously disconnected)
    • RCM_B connector disconnected. (if not previously disconnected)
    • SCCM_A connector disconnected.
    • Disconnect all in-line electrical connectors between the ABS module, the SASM and the RCM.
    • Inspect and repair all disconnected electrical connectors for the following:
      • corrosion (install new connector or terminal - clean module pins)
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Remove the steering wheel rotation sensor. Refer to REMOVAL AND INSTALLATION
      • inspect the connectors for corrosion, loose or spread terminals and loose wire connections at terminals.
      • inspect the wire harnesses for any damage, pinched, cut or pierced wires.
      • repair any concerns found. Refer to OEM CONNECTOR REPAIR PROCEDURES (EXCEPT ELECTRIC) for schematic and connector information.
    • Install the steering wheel rotation sensor. Refer to REMOVAL AND INSTALLATION
    • Connect all in-line electrical connectors between the ABS module, the SASM and the RCM. Make sure the connectors seat and latch correctly.
    • SCCM_A connector connected. Make sure the connector seats and latches correctly.
    • RCM_B connector connected. Make sure the connector seats and latches correctly.
    • RCM_A connector connected. Make sure the connector seats and latches correctly.
    • ABS Module connector connected. Make sure the connector seats and latches correctly.
    • Test drive the vehicle at speeds greater than 20 km/h (12 mph) and make at least 1 left turn and 1 right turn.
    • Carry out the ABS self-test.
    • Are any DTCs listed in the Fault Trigger Conditions Table present? 
    Yes No
    CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA.
    If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions.
    If no service articles address this concern, INSTALL a new steering wheel rotation sensor. REFER to REMOVAL AND INSTALLATION    		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector, high network traffic or an intermittent fault condition. ADDRESS the root cause of any connector or pin issues.
  14. LB14: CHECK FOR CORRECT PSCM OPERATION 
    • Ignition OFF.
    • ABS Module connector disconnected.
    • RCM_A connector disconnected. (if not previously disconnected)
    • RCM_B connector disconnected. (if not previously disconnected)
    • PSCM_A connector disconnected.
    • PSCM_B connector disconnected.
    • Disconnect all in-line electrical connectors between the ABS module, the PSCM and the RCM.
    • Inspect and repair all disconnected electrical connectors for the following:
      • corrosion (install new connector or terminal - clean module pins)
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Connect all in-line electrical connectors between the ABS module, the PSCM and the RCM. Make sure the connectors seat and latch correctly.
    • PSCM_B connector connected. Make sure the connector seats and latches correctly.
    • PSCM_A connector connected. Make sure the connector seats and latches correctly.
    • RCM_B connector connected. Make sure the connector seats and latches correctly.
    • RCM_A connector connected. Make sure the connector seats and latches correctly.
    • ABS Module connector connected. Make sure the connector seats and latches correctly.
    • Test drive the vehicle at speeds greater than 20 km/h (12 mph) and make at least 1 left turn and 1 right turn.
    • Carry out the ABS self-test.
    • Are any DTCs listed in the Fault Trigger Conditions Table present? 
    Yes No
    INSTALL a new EPAS gear.
    CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA.
    If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions.
    If no service articles address this concern, INSTALL a new PSCM. REFER to STEERING GEAR .
    ORDER a replacement PSCM and INCLUDE the RVC on the form.
    If this is a Ford paid repair, INCLUDE the RVC on the warranty claim form.    		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector, high network traffic or an intermittent fault condition. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals