| B1A01:01 |
Speaker #1: General Electrical Failure |
GO to Pinpoint Test E |
| B1A01:11 |
Speaker #1: Circuit Short To Ground |
GO to Pinpoint Test E |
| B1A01:12 |
Speaker #1: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1A01:13 |
Speaker #1: Circuit Open |
GO to Pinpoint Test E |
| B1A02:01 |
Speaker #2: General Electrical Failure |
GO to Pinpoint Test E |
| B1A02:11 |
Speaker #2: Circuit Short To Ground |
GO to Pinpoint Test E |
| B1A02:12 |
Speaker #2: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1A02:13 |
Speaker #2: Circuit Open |
GO to Pinpoint Test E |
| B1A03:01 |
Speaker #3: General Electrical Failure |
GO to Pinpoint Test E |
| B1A03:11 |
Speaker #3: Circuit Short To Ground |
GO to Pinpoint Test E |
| B1A03:12 |
Speaker #3: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1A03:13 |
Speaker #3: Circuit Open |
GO to Pinpoint Test E |
| B1A04:01 |
Speaker #4: General Electrical Failure |
GO to Pinpoint Test E |
| B1A04:11 |
Speaker #4: Circuit Short To Ground |
GO to Pinpoint Test E |
| B1A04:12 |
Speaker #4: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1A04:13 |
Speaker #4: Circuit Open |
GO to Pinpoint Test E |
| B1D55:11 |
Antenna #2: Circuit Short To Ground |
GO to Pinpoint Test A |
| B1D55:15 |
Antenna #2: Circuit Short To Battery or Open |
GO to Pinpoint Test A |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test U |
| U0198:00 |
Lost Communication With Telematic Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0237:00 |
Lost Communication With Digital Audio Control Module "C": No Sub Type Information |
GO to Pinpoint Test X |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test Y |
| U201A:51 |
Control Module Main Calibration Data: Not Programmed |
This DTC sets due to an incorrect or incomplete ACM configuration. CARRY OUT the ACM programming procedure using as-built data. REFER to: Module Configuration
. |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
This DTC sets due to an incorrect or incomplete ACM configuration. CARRY OUT the ACM programming procedure using as-built data. REFER to: Module Configuration
. |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
This DTC sets due to an incorrect or incomplete ACM configuration. CARRY OUT the ACM programming procedure using as-built data. REFER to: Module Configuration
. |
| U3000:41 |
Control Module: General Checksum Failure |
CLEAR the DTC. REPEAT the ACM self-test. If the DTC is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM)
. |
| U3000:42 |
Control Module: General Memory Failure |
CLEAR the DTC. REPEAT the ACM self-test. If the DTC is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM)
. |
| U3000:96 |
Control Module: Component Internal Failure |
CLEAR the DTC. REPEAT the ACM self-test. If the DTC is retrieved again, INSTALL a new ACM. REFER to: Audio Front Control Module (ACM)
. |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test Z |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AA |